Commit graph

2197 commits

Author SHA1 Message Date
Zoltan HERPAI
d6844b3bfa ramips: add missing USB packages into ASL26555-16M
Mirror the package list from the 8M device profile to the
16M device profile.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2018-08-13 10:26:03 +02:00
Daniel Gimpelevich
1d3ea7874d ramips: fix BR-6478ACv2 support
The wholesale changes introduced in commit f9b8328 missed this DTS file
because it hadn't been merged yet. This patch brings it in line to match
the other mt7620a devices' DTS files.

Additionally, the Internet LED is now labeled correctly and set to unused
by default, since the WAN interface is not known in every configuration.

Using sysupgrade between images before and after this commit will require
the -F flag.

Tested-by: Rohan Murch <rohan.murch@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[drop internet led default setting]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-13 08:37:19 +02:00
Ludwig Thomeczek
5543d63fc8 ramips: add support for Netgear R6120
This patch adds support for the Netgear R6120, aka Netgear AC1200.

Specification:
- SoC: MediaTek MT7628 (580 MHz)
- Flash: 16 MiB
- RAM: 64 MiB
- Wireless: 2.4Ghz(builtin) and 5Ghz (MT7612E)
- LAN speed: 10/100
- LAN ports: 4
- WAN speed: 10/100
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

To flash use nmrpflash with the provided factory.img.
Flashing via webinterface will not work, for now.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2018-08-13 08:37:19 +02:00
INAGAKI Hiroshi
a6369206fe ath79: add support for I-O DATA WN-AC1600DGR2
I-O DATA WN-AC1600DGR2 is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- Qualcomm Atheros QCA9557
- 128 MB of RAM
- 16 MB of Flash
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 3T3R (QCA9880)
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR2
2. Connect power cable to WN-AC1600DGR2 and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-08-11 21:45:06 +02:00
Mathias Kresin
3b1213a377 ramips: use #include syntax for dtsi files
Use the same syntax for including dtsi for all dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-08 07:24:03 +02:00
Chen Minqiang
f6d81e2fa1 mt7620: gsw: make IntPHY and ExtPHY share mdio addr 4 possible
To share mdio addr for IntPHY and ExtPHY,
as described in the documentation (MT7620_ProgrammingGuide.pdf).
(refer: http://download.villagetelco.org/hardware/MT7620/MT7620_ProgrammingGuide.pdf)

when port4 setup to work as gmac mode, dts like:

&gsw {
    mediatek,port4 = "gmac";
};

we should set SYSCFG1.GE2_MODE==0x0 (RGMII).
but SYSCFG1.GE2_MODE may have been set to 3(RJ-45) by uboot/default
so we need to re-set it to 0x0

before this changes:
gsw: 4FE + 2GE may not work correctly and MDIO addr 4 cannot be used by ExtPHY

after this changes:
gsw: 4FE + 2GE works and MDIO addr 4 can be used by ExtPHY

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-08-06 07:12:31 +02:00
Daniel Gimpelevich
379fe50672 ramips: fix gigabit switch PHY access on MDIO
When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.

Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Daniel Gimpelevich
5a6229a93d ramips: remove superfluous & confusing DT binding
Mediatek has a reference platform that pairs an MT7620A with an MT7530W,
where the latter responds on MDIO address 0x1f while both chips respond on
0x0 to 0x4. The driver special-cases this arrangement to make sure it's
talking to the right chip, but two different ways in two different places.
This patch consolidates the detection without the current requirement of
both tests to be separately satisfied in the DTS.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Daniel Gimpelevich
f72fa883b3 ramips: add support for Edimax BR-6478AC v2
Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie.
Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated.

Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Macronix MX25L6405D
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7612E 5GHz 802.11ac
- Switch: Mediatek MT7530W Gigabit Switch
- USB: Yes 1 x 2.0

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
4. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Alex Maclean
6031ab345d ramips: move partitions into partition table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-08-04 08:39:35 +02:00
Mathias Kresin
6dd94c2781 ramips: unify partition node names in dts files
Use partition@ as name for all partition nodes. Add a label where
necessary.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
bfd65fc4ab ramips: fix whitespace and comment issues in dts
Fix space vs. tabs issue and trainling whitespaces. Use C style
comments or drop the comments if they explain what is already to see in
the devicetree parameters.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
53624c1702 ramips: fix dtc warnings
Fix individual boards dtc warnings or obvious mistakes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
6384e0d16a ramips: fix hnat dtc warning
The hardware NAT node has the same reg/unit as the ethernet node. One
of them need to be a child of the other.

Make the hardware NAT node a child of the ethernet node since the it
"reference" the netdev in its properties.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
f9b8328d79 ramips: fix pci/pcie related dtc warnings
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.

Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.

Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.

If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.

Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.

Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
d8e7a526a3 ramips: use ralink,nr-gpio instead of ralink,num-gpios
Since commit c1e7738988f5 ("checks: add gpio binding properties check")
dtc treats any *-gpios and *-gpio property as phandle at least during
checks. The only whitelisted property is nr-gpio.

Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false
positive warnings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
1bad2b74ae ramips: fix cpu interrupt controller dtc warnings
The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
b9dbf3f3c8 ramips: fix cpu related dtc warnings
We need a reg property if we are using a unit address.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
René van Dorst
0ae9396556 treewide: convert gpio-export to platform driver
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.

gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.

Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Stijn Tintel
22b9f99b87 kernel: bump 4.14 to 4.14.59
Drop patch that was superseded upstream:
ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch

Drop upstreamed patches:
- apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch
- apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch
- ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch
- generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch
- generic/pending/900-gen_stats-fix-netlink-stats-padding.patch

In 4.14.55, a patch was introduced that breaks ext4 images in some
cases. The newly introduced patch
backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
addresses this breakage.

Fixes the following CVEs:
- CVE-2018-10876
- CVE-2018-10877
- CVE-2018-10879
- CVE-2018-10880
- CVE-2018-10881
- CVE-2018-10882
- CVE-2018-10883

Compile-tested: ath79, octeon, x86/64
Runtime-tested: ath79, octeon, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 05:11:07 +03:00
INAGAKI Hiroshi
ce93445cd6 ramips: add support for ELECOM WRC-2533GST
ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Core, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 4T4R 2.4/5 GHz wifi
  - MediaTek MT7615
- 5x 10/100/1000 Mbps Ethernet
- 4x LEDs, 6 keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Connect the computer to the LAN port of WRC-2533GST
2. Connect power cable to WRC-2533GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-30 15:55:21 +02:00
Thibaut VARÈNE
3fd4db76b0 ramips: fix RBM11G name
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:43:37 +02:00
Thibaut VARÈNE
a9494bb425 ramips: fix RBM33G name
The device name is corrected to match the hardware-stored (in hard config
flash space) device name.

Tested-by: Tobias Schramm <tobleminer@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 10:43:37 +02:00
LoveSy
974a2b1aa9 ramips: mmc: Add SD card support to HC5661A
Tested on HC5661A and it now fixes the issue that when enabling sd card
in HC5661A, the wan and 3 lan ports will down.

Known issue:
- When enabling SD card support, the led light of system will down and the rest 2 lights keep working.

Signed-off-by: LoveSy <shana@zju.edu.cn>
2018-07-30 10:43:37 +02:00
LoveSy
3a8efaef00 ramips: mmc: Fix init for MT7628AN
There is another thing about crc to do when initialize SD card on
MT7628.
This commit is to fix this init issue.

Signed-off-by: LoveSy <shana@zju.edu.cn>
2018-07-30 10:43:37 +02:00
Mathias Kresin
4cbf5601f9 ramips: remove stale get_status_led call
The get_status_led() function was removed due to the convertion to dts
alias based status led.

Since we don't need the boardname any longer, the functions.sh include
isn't required any more.

Fixes: c9c4b2116c ("ramips: Use dts alias based status led")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-25 08:57:17 +02:00
Thibaut VARÈNE
c4f09fc9f8 ramips: define common MikroTik RouterBOARD image recipe
All these devices share the exact same image format.

The usb3 kmod is added for the rbm11g, as the rbm11g has a mini-pcie
slot like its bigger sibling. The usb kmod is necessary for
usb-over-pcie support, which is mandatory for a lot of LTE modules.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-19 18:58:24 +02:00
Chuanhong Guo
c9c4b2116c ramips: Use dts alias based status led
Also fix several typos in led node name.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-07-16 15:12:18 +02:00
Felix Fietkau
2601e34fad ramips: ethernet: disable fraglist support
The code has some remaining issues that cause ethernet hangs, so
disable it for now until we can get it fixed

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-14 08:32:39 +02:00
Felix Fietkau
0c285bd081 ramips: ethernet: use own page_frag_cache
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.

Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-12 18:43:53 +02:00
Felix Fietkau
01df4a2565 ramips: ethernet: use skb_free_frag to free fragments
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-12 18:43:53 +02:00
Peter Lundkvist
2eeb4b78c6 ramips: TP-Link TL-WR902AC v3: add missing wps button
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
2018-07-12 18:15:33 +02:00
Peter Lundkvist
33321ebefa ramips: TP-Link TL-WR902AC v3: don't build factory image
The line that produces factory image was accidentally left by me while
testing before inital commit.

I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).

I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.

So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:15:33 +02:00
Mathias Kresin
cf7154db07 kernel: only optimized for size if small_flash
Add a new config option to allow to select the default compile
optimization level for the kernel.

Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.

Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.

Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.

Exceptions to the above are:

  - lantiq, where the optimization for size is only required for the
    xway_legacy subtarget but was set for the whole target
  - mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
    plenty of space and an optimization for size doesn't make much sense
  - rb532, which has 128MByte flash

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:15:32 +02:00
Felix Fietkau
33553a11ab ramips: clean up and fix MT7621 NAND driver issues
- remove misaligned custom buffer allocation in the NAND driver
- remove broken bounce buffer implementation for 16-byte align

Let the MTD core take care of both

Fixes messages like these:
[  102.820541] Data buffer not 16 bytes aligned: 87daf08c

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-11 20:59:44 +02:00
Koen Vandeputte
ba2b0f0ac6 kernel: bump 4.14 to 4.14.54
Rereshed all patches

Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-11 16:02:24 +02:00
Ademar Arvati Filho
16d6a63f85 ramips: add support for Blueendless Kimax U35WF
Blueendless Kimax U35WF is a 3,5" HDD Enclosure with Wi-Fi and Ethernet

Patch rewritten from: https://forum.openwrt.org/viewtopic.php?id=66908
Based on: https://github.com/lede-project/source/pull/965

Specification:
- SoC: MediaTek MT7620N
- CPU/Speed: 580 MHz
- Flash-Chip: KH25L12835F Spi Flash
- Flash size: 16 MiB
- RAM: 64 MiB
- LAN: 1x 100 Mbps Ethernet
- WiFi SoC-integrated: 802.11bgn
- 1x USB 2.0
- UART: for serial console

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
3. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-07 21:07:40 +02:00
INAGAKI Hiroshi
0b83a23560 ramips: add support for I-O DATA WN-AX1167GR
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Stock firmware:

In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.

(excerpt from dmesg):

MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"

The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.

If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.

(example):

## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1  !!
## Booting image at bc060000 ...
   Image Name:   MIPS OpenWrt Linux-4.14.50
   Image Type:   MIPS Linux kernel Image (lzma compressed)
   Data Size:    1865917 Bytes = 1.8 MB
   Load Address: 80001000
   Entry Point:  80001000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!

Starting kernel ...

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-07 21:07:40 +02:00
Romain MARIADASSOU
ce31bdc20c ramips: add support for TL-WA801ND v5
Specification:

- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn

Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.

Flash instructions:

1) To flash the recovery image, start a TFTP server with IP address
   192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
   button and power it up. Keep pressing the WPS/Reset button for
   10 seconds or until the lock LED is lighting up.
   It will try to download the recovery image and flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-07-04 01:20:02 +02:00
Maxim Anisimov
7d07bc96b7 ramips: add support for ZyXEL Keenetic Extra II
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button

The device supports dual boot mode. So we use only first half of flash.

Flash instruction:

The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
   to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-07-04 01:20:02 +02:00
Maxim Anisimov
9e2c28472c ramips: move zyimage define to common Makefile
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-07-04 01:20:02 +02:00
Tobias Schramm
faf64056dd ramips: add support for MikroTik RouterBOARD RBM11g
This commit adds support for the MikroTik RouterBOARD RBM11g.

=Hardware=

The RBM11g is a mt7621 based device featuring one GbE port and one
miniPCIe slot with a sim card socket and USB 2.0.

==Switch==

The single onboard Ethernet port is connected the CPU directly.
The internal switch of the mt7621 SoC is disabled.

==Flash==

The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS
connected to CS0.

==PCIe==

The board features a single miniPCIe slot. It has a dedicated mini SIM
socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via
GPIO9.

==USB==

There are no external USB ports.

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack (center-positive). The input voltage range is 11-32 V.

==Serial port==

The device does have an onboard UART on an unpopulated header next to the
flash chip:

GND: pin 2
 TX: pin 7
 RX: pin 6

Settings: 115200, 8N1

See below illustration for positioning of the header.

0 = screw hole
* = some pin
T = TX  pin
R = RX  pin
G = GND pin

Pinout:
+---------------
|O
|             __
|            /  \
|            \__/
|
|
|
|               +---+
|               |RAM|
| +--+          |   |
| |**|  <- unpopulated header with UART
| |*T|          +---+
| |R*|        +--------+
| |**|        |        |
| |G*|        |  CPU   |
| +--+        |        |
|    +--+     |        |
|    |  |     +--------+
|    +--+  <- flash chip
|O
|       +-----+
|       |     |
|+--+   |     |
||  |   |     |
+---------------------

=Installation=

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM11G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the
output directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the
created license file.**

When rebooted the board will try booting via ethernet first. If your
board does not boot via ethernet automatically you will have to attach
to the serial port and set ethernet as boot device within RouterBOOT.

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin"
   initramfs image
2. Connect to ethernet port on board
3. Power on the board
4. Wait for OpenWrt to boot

Right now OpenWrt will be running with a SSH server listening. Now
OpenWrt must be flashed to the devices flash:

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
   to the device using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"

Once the flashing completes the board will reboot. Disconnect from the
devices ethernet port or stop the DHCP/TFTP server to prevent the device
from booting via ethernet again.
The device should now boot straight to OpenWrt.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-07-04 01:20:02 +02:00
Felix Fietkau
09b6755946 ramips: limit dictionary size for lzma compression
In some cases, recent builds fail to boot from flash with at least some
MT7621 based devices. The error message is:
"LZMA ERROR 1 - must RESET board to recover"
Booting the same kernel via TFTP works for some reason.

Through testing I figured out that limiting the LZMA dictionary size
seems to prevent these errors

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-03 11:18:39 +02:00
Lev
3d6f57f3c6 ramips: fix wizfi630a swapped lan/wan port
The order of the Ethernet ports were mixed up.
This commit fixes the order to be aligned with the physical layout.

Signed-off-by: Lev <leventelist@gmail.com>
2018-07-02 06:59:31 +02:00
Mathias Kresin
a570933999 treewide: gpio-export: add error handling
Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Andrey Jr. Melnikov
19c7e950af ramips: move mt7620n i2c_pins definition to right place
Move to i2c pins pinmux node to the pinctrl node.

Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")

Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
INAGAKI Hiroshi
0efd0308a0 ramips: add switch port index for I-O DATA WN-GX300GR
WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are
orderd on the device as follows:
4 3 2 1 0

1-4: lan
0: wan

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-27 08:42:54 +02:00
Alex Maclean
2f23a0583a ramips: RE350: add rootfs offset to header
Have mktplinkfw fill in the rootfs offset so the firmware splitter can
find it without aligning to erase blocks.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-06-26 07:04:43 +02:00
Franz Flasch
8375623a06 ramips: add support for TP-Link Archer C2
Specification:

- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond 25Q64BVSIG
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7610EN 5GHz 802.11ac
- Switch: RTL8367RB Gigabit Switch
- USB: Yes 1 x 2.0

Preparing a TFTP recovery image for initial flashing:

Currently the only method to install openwrt for the first time is via
TFTP download in u-boot. After first install you can use regular updates.
WARNING: This method also overwrites the bootloader partition!

Create a TFTP recovery image:

1) Download a stock TP-Link Firmware file here:
     https://www.tp-link.com/en/download/Archer-C2_V1.html#Firmware
2) Extract u-boot from the binary file:
     #> dd if=c2v1_stock_firmware.bin of=c2v1_uboot.bin bs=1 skip=512 count=131072
3) Now merge the sysupgrade image and the u-boot into one binary:
     #> cat c2v1_uboot.bin openwrt-squashfs-sysupgrade.bin > ArcherC2V1_tp_recovery.bin

The resulting image can be flashed via TFTP recovery mode.

Flash instructions:

1) To flash the recovery image, start a TFTP server from IP address
   192.168.0.66 and serve the recovery image named
   ArcherC2V1_tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS/Reset button
   and power it up. Keep pressing the WPS/Reset button for 10 seconds.
   It will try to download the recovery image and flash it.

It can take up to 20-25 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00
Franz Flasch
abb7524683 ramips: fix ZyXEL Keenetic Viva switch config
The rtl8367b driver never supported a mdio property and it is quite
likely that the switch never worked for the board.

Use the mii-bus property instead to manage the switch via a mdio bus.

Signed-off-by: Franz Flasch <franz.flasch@gmx.at>
2018-06-25 20:52:18 +02:00