At offset 0x40, signature for TL-MR10U/TL-MR11U begin
from 0x00, not 0x10/0x11.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36727
MR10U is closer to MR3040 than WR703N. This changes also
enable USB power on GPIO18.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36726
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both
RX and TX traffic from LAN port 1 to LAN port 4:
$ swconfig dev switch0 set enable_mirror_rx 1
$ swconfig dev switch0 set enable_mirror_tx 1
$ swconfig dev switch0 set mirror_monitor_port 4
$ swconfig dev switch0 set mirror_source_port 1
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 36713
* update the bootcode.bin to the newest version
- gpu/cpu mem split is now configured through config.txt, so no need
to create more than one sd card image (just edit the config.txt)
- bootcode.bin now supports the never revision 2 raspberry pis
* add a commented prepopulated config.txt for easier config changes
Taken from <https://github.com/Evilpaul/RPi-config>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36668
Check bootloader argument in mtd.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo@openwrt.org: split into two patches, one for detection,
one letting bcm63xxpart use it.]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36659
Don't build the CRAMFS file system module in the kernel, and save some bytes.
No bcm63xx board needs this obsolete file system, neither those ones using
the Redboot bootloader (liveboxes). Thus, there is no need to build it, since it has
been replaced long time ago by squashfs.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 36616
zsmalloc was changed to a bool because of missing exports in the kernel,
but we already export the required symbol, so change it back to tristate.
Closes#13481.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36587
This allow us to increase the kernel partition size,
and ensures, that the -factory image still usable via
the original interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36584
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36580
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36579
Here is corrected version (only thing not working are wifi LEDs).
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36578
These devices are actually built around the 8devices Carambola dev board.
ARC FreeStation, Flex mARC, iFlex, and SplitStation devices are
supported with this image, see "ARCFlex Firmware Downloads":
http://www.antennas.com/wiki/index.php?title=ARC-OS_Firmware_Downloads_and_Revision_History
Funnily enough if present the external USB wlan ends up being wlan-0, with the
SoC device being wlan-1.
- Invert port map so special handling of vlan config can be removed.
- Add LED config similar to original ArcOS firmware.
- Add GPIO export for enabling PoE passthrough from ethernet port 0 to port 1
- Get MACs from factory partition.
- Update description to list supported devices.
- Carambola uses RT3050 (not RT3052), though my Carambola CPU
actually reports itself as being an RT3350 while still having
RT3050F markings.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 36564
And while at it, also include a define check for BCM6328, thanks to
Gabor for spotting this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36506
Update the numbering of kernel patch for supporting
Netgear WNR2000v3 from 617 to 618.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36498
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.
The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 36482
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36459
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36456
Only difference between Generic and P1020 is that P1020
enables SMP with two CPUs in the kernel config.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36454
This upgrades the AT91 target to 3.8.7, and migrates to device tree.
This allows a single kernel to be built for most at91 variants which
simplifies things quite a bit. The immediate result is that all
subtargets are nuked, and any boards without dts files are no longer
supported, though the target now includes more boards than before. The
adc driver was also nuked as 3.8.7 includes a new one under the IIO
subsystem.
Signed-off-by: Adam Porter <porter.adam@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36452
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports':
drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36442
Now that ALL5002 and ALL5003 each got their own DTS and board names, remove
the now no longer needed user-space part which previously differentiated between
ALL5002 and ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3558/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36436
Prior to the switch to 3.8, ALL5002 and ALL5003 boards shared mach-all5002.c.
With the change to DTS, this is no longer accurate, as ALL5002 is based on
Rt3352 SoC while ALL5003 is based on Rt5350 SoC, therefore the corresponding
rt5350.dtsi need to be included for ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3557/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36435
This board uses a TrendChip SOC with its own RAM/Flash for ADSL support.
We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN.
There are two versions (Chile 8MB and Spain 16MB).
Wiki: http://wiki.openwrt.org/toh/alpha/asl26555
Signed-off-by: Esteban Benito <estebanjbs@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3571/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36433
Fixes the following warning:
CC [M] net/ipv6/addrconf.o
net/ipv6/addrconf.c: In function 'addrconf_init':
net/ipv6/addrconf.c:4944:2: warning: assignment from incompatible pointer type [enabled by default]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36364
prepare_generic_squashfs was called twice on the generated images breaking mount_root
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36349
this adds basic support. the bootloader on these units is locked down.
until we have a replacement we can do basic testing with these env variables in uboot.
set update_openwrt erase 0xb0020000 0xb073ffff \;tftp 0x81000000 openwrt-lantiq-xway-VG3503J-squashfs.image\;cp.b 0x81000000 0xb0020000 \$(filesize)
set bootcmd cp.b 0xb0020000 0x80002000 0x400000\; go 0x80002000
unfortunatley the bootloader ignores the bootcmd, so autobooting is not possible yet. you need to call "run bootcmd" by hand after each power cycle.
please note that the vdsl firmware is non redistributable. you can find it in the GPL drop that BT provides.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36315
Update ehci/ohci driver registration to conform to the new platform
drivers.
This fixes missing USB host support in 3.8.x
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 36309
Add support for PMC PM25LQ032 (4MB) SPI Flash used in Hame MPR-A1 and clones.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36296
3.3 and 3.6 kernels do not make use of the UAPI headers, still they need
to provide an up-to-date switch.h copy for swconfig to build.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36295
