This adds support for Byte Queue Limits in bgmac and b44, now it is
possible to use more advanced network queue control algorithms.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38038
This updates the patches for BCM5354 to the version send for upstream
Linux inclusion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38037
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38036
This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.
The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.
It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.
Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset
button, image to be used for upgrade from OEM firmware's web interface
Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970>
Issue:
* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
reset during kernel decompress.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
SVN-Revision: 38011
A new type of partition with magic FCTY was found on Huawei E970:
46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38005
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38004
Add a new kernel config option for generic firmware partition
split support and change the uImage split support to depend on
the new option. Aslo rename the MTD_UIMAGE_SPLIT_NAME option to
MTD_SPLIT_FIRMWARE_NAME to make it more generic.
The patch is in preparation for multiple firmware format
support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38002
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38001
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. Now it should be
possible to read decimal and hex vars of max 8 bit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37999
Most of the bcm47xx devices use TRX format for storing kernel and some
partition like Squashfs or JFFS2. This is pretty flexible solution, CFE
(the bootloader) just writes (and later boots) TRX at some hardcoded
place and paritions can vary in the size.
However some devices don't use TRX format. Very recently we have
discovered ZTE H218N that has kernel and rootfs partitions at some
"random" places.
This patch allows Linux find a rootfs partition after installing custom
image with a CFE bootloader.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 37998
Separate OpenWrt specific MTD options from the mainline
option by moving those into a new submenu in the kernel
configuration interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37997
* Use different structs depending on the number of nvram variables to check.
* Add detection of ZTE H218N, this closes#14151.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37996
The revision is stored in a different register than it is in other
Broadcom switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37995
These switches are integrated in some recent BCM53XX and BCM47XX SoCs
like the BCM53572.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37994
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 37993
The Linksys wrt310n v1 does not have a robo_reset config variable in
nvram, but GPIO Pin 8 is the pin needed for resetting the external
switch, Linksys hard coded it into their source code.
Thank you Devastator for testing.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37988
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37977
- change patch numbers to group the related stuff together,
- add mtd prefix where it is missing,
- use hyphens in the patch names
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37974
This patch adds support for building firmware images for the
TP-Link TL-MR3040 v2. Tested and working on v2.1 hardware.
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37964
I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37963
The skb is usually started by a padding which allows the protocols in the
network stack to add their headers in front of the payload. The skb can be
reallocated in case the preallocated padding is not large enough. This can for
example happen in the function __skb_cow which will check the requested extra
headroom and allocate more buffer when the requested headroom is bigger than
the available one. The extra buffer is aligned again to the multiple of the
NET_SKB_PAD of the target architecture.
The macro used to create the multiple of the NET_SKB_PAD is written in a way
which allows only values power two as alignment parameter. The currently used
value of 48 bytes can not be written as n ** 2 but as 2 ** 4 + 2 ** 5. The
extra buffer is therefore not always the multiple of 48 but can be 16, 64, 80,
128, 144 and so on. The generated values are also not monotonic (48 requested
bytes are mapped to 80 allocated bytes and 49 requested bytes are mapped to 64
allocated bytes).
These unexpected small values result in more reallocations of the buffer. This
was noticed prominently during tests between two QCA9558 720 MHz devices which
were connected via ethernet to PCs and had a HT40 802.11n 3x3 link between each
other. The throughput PC-to-PC during iperf TCP runs increased reliable from
186 Mibit/s to 214 Mibit/s in one direction and from 195 Mibit/s to 220 Mibit/s
in the other direction. This is a performance increase of ~14% just by reducing
the amount of reallocations.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 37948
Currently, the module causes an oops at least on rt5350. These patches
have been accepted upstream at:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 37931
BCM5365 (and probably other older variants) use a different phy id, so
the phy driver never attached for them.
Fix this by adding the appropriate phy id to the fixup and the phy
driver.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37906
b53_no_ops has no elements and b53_port_ops has one element, this makes
the code access some random memory when trying to access the mib
counter functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37895
Every device I connect to the USB port is detected as 2-1, not 1-1.
So adjust the default setting accordingly.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37882
When the squashfs and jffs2 images are generated
in the same turn, the compressed kernel images
are generated twice with the same parameters.
Move compressed kernel generation into a separate
phase to avoid that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37881
The myloader partition parser code uses ifdef wrappers
to make the code usable on kernels below version 3.2.
All targets are using kernel 3.3 at least so the wraper
is not needed. Remove that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37880
Those are not needed since we are generating the
initramfs images along with the others.
Remove the variables and use the template names
directly.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37876
Initramfs images are not generated for profiles which
are using the squashfs-only template. Add the missing
'Image/Build/Template/squashfs-only/initramfs' to fix
that.
Also, 'Image/Build/Cameo933x/initramfs' uses wrong
parameters for 'MkuImageLzma/initramfs' due to a
misplaced commma. Remove that to fix the generated
initramfs images.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37871
Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.
Russell says in the original patch:
"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built. The patches
required no changes."
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37869
Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.
Russell says in the original patch:
"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built. The patches
required no changes."
The current patch contains additional configuration tweaks.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37868
Add kernel configuration and patches for Linux 3.10.
Taken from the 'alix2: update to LINUX_VERSION 3.10.9'
patch: http://patchwork.openwrt.org/patch/3971/.
Russell says in the original patch:
"Initial whack at updating alix2 to a current kernel. It builds
and runs without problems so far. I copied target/linux/config-3.8,
target/linux/x86/alix2/config-3.8, and target/linux/patches-3.8 to
their 3.10 equivalents and tweaked until it built. The patches
required no changes."
The current patch contains additional configuration tweaks,
and the kernel patches were refreshed.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37867
The 'Warning: unable to open an initial console' message
indicates an error in the rootfs. Remove the patch which
hides the warning.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37848
Linux expects that the /dev/console node is present
in the rootfs image. Create the node in initramfs,
in order to make std{in,out,err} usable even in early
init process.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37846
Apparently registering usb device on newest trunk causes
this AP not to boot...
Since there is no USB socket in that device anyway this
can be simply removed (and device boots then no problem).
[juhosg:
- tweak subject line and description,
- remove #include "dev-usb.h",
- remove 'select ATH79_DEV_USB' from Kconfig]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37844
The USB controller is sitting on the PCI bus and
without the package the EHCI controller is not
usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37835
Fix the following warning:
arch/mips/pci/pci-rt3883.c: In function 'rt3883_pci_probe':
arch/mips/pci/pci-rt3883.c:458:4: warning: use of 'h' length modifier with 'a' type character [-Wformat]
Signed-off-by: Michael Lee <igvtee@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37827
Fixes the following build error on ramips/rt3883:
arch/mips/pci/pci-rt3883.c:488:3: error: implicit declaration of function \
'of_pci_get_devfn' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Although the function is only used by the PCI driver
of the RT3883 SoC but at the moment but it might be
useful for other targets as well.
Signed-off-by: Michael Lee <igvtee@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37826
vsnprintf returns the number of chars that would have been written, not
the actual number of chars written. This can lead to crashlog_buf->len
being too big which in turn can lead to get_maxlen() returning negative
numbers. The length argument of kmsg_dump_get_buffer will be casted to
a size_t which makes a negative input a big positive number allowing
kmsg_dump_get_buffer to write out of bounds.
Fix this by using vscnprintf which returns the actually written number
of chars.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 37820
The patch in question has been accepted upstream in commit:
55bf75b7dd8ec875d048824f3cdecf8254e292e5
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37807
Based on the original firmware, the file must have the tag
HORNET-PACKET-DIR505A1-3, not HORNET-RT-DIR505A1-3.
http://patchwork.openwrt.org/patch/3945/
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 37781
With
.config:CONFIG_X86_GRUB_SERIAL=""
which (AFAICT) is the way to tell GRUB not to use a serial console, in
target/linux/x86/image/Makefile:ifneq ($(CONFIG_X86_GRUB_SERIAL),)
$(CONFIG_X86_GRUB_SERIAL) expands to `""' (a literal double double-quote),
making the condition unconditionally false.
This patch fixes the situation by passing CONFIG_X86_GRUB_SERIAL through
qstrip before testing.
Signed-off-by: Tamas TEVESZ <ice@extreme.hu>
SVN-Revision: 37749
opkg (and possible other tools) are currently broken as it requires
file locking support enabled in the kernel.
Without this results in a message like:
root@OpenWrt:/etc/config# opkg update
Collected errors:
* opkg_conf_load: Could not lock /var/lock/opkg.lock: Permission denied.
With this patch opkg is fully functional on this platform.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37745
*) can not connect to switch chip
*) only one usb port is working
*) wifi is not working
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37712
The BCM4331 supports a PCIe max request size of 512 bytes and uses
that, but the PCIe controller in the BCM4706 just supports 128 Bytes
and that causes a DMA error for packages bigger than 126 bytes. This
fixes the problem by setting the BCM4331 also to 128 Bytes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37709
Parallel flash access on RT3662/RT3883 based devices
is broken without that. It was fixed already some time
ago, but that change seems lost somewhere.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37708
This patch fixes the code of the buttons for TP-Link WA901ND.
Signed-off-by: Rocco Folino <lordzen@autistici.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37696
Job control is turned off because it cannot obtain controlling terminal on
/dev/console, so it is impossible to do any job control operation behind
real x86 device (keyboard+monitor or virtualized).
This patch switches /dev/console to tty devices for ash on x86 generic target.
Signed-off-by: Jiri Slachta <slachta@cesnet.cz>
SVN-Revision: 37693
CONFIG_FW_LOADER=y is set in the generic config and our packages in
packages/kernel/linux are depending on it to be compiled into the
kernel.
This fixes some dependency problem where kmod-r8169 misses
firmware_class.ko.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37672
brcm47xx does not use CONFIG_B53_SPI_DRIVER, but it could be selected if spi is build as a module
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37656
OCF_CRYPTOSOFT uses both symbols form crypto_hash and crypto_blkcipher,
so let it select these through kernel config.
Fixes the following build error:
ERROR: "crypto_alloc_ahash" [crypto/ocf/cryptosoft.ko] undefined!
ERROR: "crypto_ahash_digest" [crypto/ocf/cryptosoft.ko] undefined!
ERROR: "crypto_ahash_setkey" [crypto/ocf/cryptosoft.ko] undefined!
make[6]: *** [__modpost] Error 1
make[5]: *** [modules] Error 2
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37652
This uses a new switch driver.
The old ADMTEK Adm6996 switch is not supported any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37650
This is untested, but probably needed to make it work with the phy lib switch driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37649
This is needed for some switches used on bcm47xx SoCs like the one on the Asus RT-N66U.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37645
bcm47xx_nvram_gpio_pin() returns a gpio pin number for a given name based
on configuration data in nvram.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37644
This commit adds the basic elements to support Poray brand routers.
It contains a tool to do the encryption/obfuscation that is used in
Poray routers.
Support for Poray devices was worked on by:
Felix Kaechele <heffer@fedoraproject.org>
Luis Soltero <lsoltero@globalmarinenet.com>
Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 37635
Small router sold in EU: AR9330@400MHz, 1x USB2.0,
2x ethernet, 8MB flash, 32MB ram, one led, one button.
See: http://galeria.tech-blog.pl/TP-Link_TL-WR710N-EU/
[juhosg: use a separate kernel patch]
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3873/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37572
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37571
Mercury MW4530R is a TP-Link TL-WDR4310 clone but
with a much lower price tag (~ $40). This patch
is tested to work at trunk r37525.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3856/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37570
Looks like trunk@37090 has changed the logic that determines
if router's button was pressed. This resulted in TEW632BRP
always booting into failsafe mode because it detected pressed
button (which was not pressed).
Measure with voltmeter has shown that buttons on this router
are actually active-low. This patch reflects this fact in
board configuration and fixes 'load info failsafe mode' issue.
Note: it looks like Trendnet TEW632BRP and a close relative
to TEW-652BRP V1.0 and D-Link DIR-615C1, so same problem may
exist on those routers as well. This patch doesn't affect
routers other than 632BRP and unfortunately I do not have
hardware to test this issue with other routers.
This patch fixes#13893 and is tested on actuall Trendnet
TEW632BRP.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37569
Create a separate board profile and update the profile
name in image/makefile. Also use the correct machtype
string in kernel command line.
Based on andelf's patch:
http://andelf.diandian.com/post/2013-05-22/40050677370
Signed-off-by: Oleg Titov <oleg.titov@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3840/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37550
This is a really ugly hack but it will have to do until we copy the ramips patches to the lantiq tree
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 37539
r37505 add support for Huawei HG255D, but it only tested under a community hacked u-boot ("lintel u-boot"), which has a different mtd layout compared to origin one. If you install it on a box with origin u-boot, the origin factory part will be destroyed, and your wifi interface will never up!!!
This patch shrink firmware part in mtd layout to exclude origin factory part, and I will prepare another patch to fix the eeprom extract issue for box with origin u-boot.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37530
Get rid of some ifdefs, and make sure that the microMIPS
specific code is disabled as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37506
HG255D is a kind of popular low-end home gateway in China, this patch bring the the trunk support for it. It is adapted from a local Chinese community (www.right.com.cn), so credit should given to them.
This patch is tested to work except trivial LED issues.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37505
There is no platform using the gpio-pwm driver, yet these patches break the
generic PWM framework that is in upstream. So just remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 37490
This reverts r37477. A generic patch is used to fix
this globally, so revert the ar71xx specific change.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37480
This allows the compiler to remove the emulate_load_store_microMIPS
function if cpu_has_mmips is defined as zero.
Backport of commit 74338805ec6869594d583535f941cb478c94dd73
from 3.11-rc1.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37478
Drop the local get_mtd_part_size implementation and use
the equivalent function provided by lib/functions.sh.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37476
TL-WR941N v6 use almost same IC as WDR3500.
[juhosg: change subject, and change fw layout from 4M to 4Mlzma]
Patchwork: http://patchwork.openwrt.org/patch/3719/
Signed-off-by: ShuYu Wang <andelf@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37471
The images which are usable with Qemu have a '-initramfs'
suffix. Update the readme to reflect that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37454
It hasn't been buildable for a long time, and there are no users of it
anymore left as all of them have been switched to the upstream accepted
version.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37436
This makes it possible to use swconfig to controll the switch.
This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.
SVN-Revision: 37304
