Commit graph

18732 commits

Author SHA1 Message Date
Serg Studzinskii
eb58b14d27 ramips: tl-wr840n-v5: increase firmware partition for 4Mmtk layot
According to console log during TP-Link TL-WR840N v5 OEM firmware update
procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store
router's configuration settings, is erased and recreated again during every
OEM firmware update procedure, thus does not contain any valuable factory data.
So it is conviniant to use this extra 64kB erase block for jffs overlay due
limited flash size on this device like it used on TP-Link's ar71xx boards.

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
2018-01-18 08:04:18 +01:00
尤晓杰
a7e62b4be1 kirkwood: fix sysupgrade
The platform_check_image() stub need to return 0 for success, otherwise
the sysupgrade will fail with:

  Image check 'platform_check_image' failed.

Fixes: aa6f5f1787 ("kirkwood: use image metadata")
Signed-off-by: 尤晓杰 <yxj790222@163.com>
[reworded commit message}
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-18 07:26:28 +01:00
Mathias Kresin
b6868e2f47 ipq806x: fix ZyXEL NBG6817 sysupgrade
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.

It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.

Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-18 07:22:37 +01:00
Gabor Juhos
ec4e9a88ff ar71xx: drop mdio-gpio.h include from mach-om5pacv2.c
The setup code of the OpenMesh OM5P ACv2 device uses nothing
from the mdio-gpio.h header, so remove the inclusion of that.

Also remove the kernel version check which is needed only
because the mdio-gpio.h header exists in a different path
in older kernels.

Compile tested only.

Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Koen Vandeputte
d3afd2a400 cns3xxx: switch to kernel 4.14
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte
9e7d53c3fe cns3xxx: refresh patches
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte
7f93624d5f cns3xxx: remove deprecated uart flags
Flag UPF_NO_TXEN_TEST is deprecated.

Remove it.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte
f3dec44520 cns3xxx: fix ethernet IRQ imbalance in 4.14
Kernel 4.14 contains more warnings regarding NAPI usage, which showed
following warning:

[ 4016.420000] ------------[ cut here ]------------
[ 4016.430000] WARNING: CPU: 1 PID: 14 at kernel/irq/manage.c:525
__enable_irq+0x3c/0x78
[ 4016.440000] Unbalanced enable for IRQ 51
[ 4016.440000] Modules linked in: ath9k ath9k_common pppoe ppp_async
ath9k_hw ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat
ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat
xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS
xt_REDIRECT xt_LOG slhc nf_reject_ipv4 nf_nat_redirs
[ 4016.500000] CPU: 1 PID: 14 Comm: ksoftirqd/1 Tainted: G        W
       4.14.11 #0
[ 4016.500000] Hardware name: Gateworks Corporation Laguna Platform
[ 4016.510000] Backtrace:
[ 4016.510000] [<c010a28c>] (dump_backtrace) from [<c010a56c>]
(show_stack+0x18/0x1c)
[ 4016.520000]  r7:c059df4b r6:00000000 r5:60000093 r4:00000000
[ 4016.530000] [<c010a554>] (show_stack) from [<c048b04c>]
(dump_stack+0x94/0xb4)
[ 4016.530000] [<c048afb8>] (dump_stack) from [<c011760c>]
(__warn+0xc8/0xf8)
[ 4016.540000]  r7:c059df4b r6:c015144c r5:00000000 r4:cf863e08
[ 4016.550000] [<c0117544>] (__warn) from [<c011767c>]
(warn_slowpath_fmt+0x40/0x48)
[ 4016.550000]  r9:cf863eb0 r8:00000036 r7:00000000 r6:c0636360
r5:00000033 r4:cf80a500
[ 4016.560000] [<c0117640>] (warn_slowpath_fmt) from [<c015144c>]
(__enable_irq+0x3c/0x78)
[ 4016.570000]  r3:00000033 r2:c059e0c5
[ 4016.570000] [<c0151410>] (__enable_irq) from [<c01514ec>]
(enable_irq+0x64/0x7c)
[ 4016.580000] [<c0151488>] (enable_irq) from [<c0335c14>]
(eth_poll+0x28c/0x558)
[ 4016.590000]  r5:d08926c0 r4:cf894488
[ 4016.590000] [<c0335988>] (eth_poll) from [<c03b1718>]
(net_rx_action+0xfc/0x2e8)
[ 4016.600000]  r10:cf863eb8 r9:cf863eb0 r8:00000001 r7:0f7b5000
r6:c0636360 r5:cfdeb360
[ 4016.610000]  r4:cf894488
[ 4016.610000] [<c03b161c>] (net_rx_action) from [<c0101510>]
(__do_softirq+0xe0/0x228)
[ 4016.620000]  r10:00000100 r9:c070204c r8:c0702040 r7:00000003
r6:00000008 r5:40000003
[ 4016.620000]  r4:cf862000
[ 4016.630000] [<c0101430>] (__do_softirq) from [<c011ae28>]
(run_ksoftirqd+0x34/0x58)
[ 4016.630000]  r10:c0133964 r9:00000000 r8:00000001 r7:00000000
r6:c070b44c r5:cf862000
[ 4016.640000]  r4:cf8037e0
[ 4016.640000] [<c011adf4>] (run_ksoftirqd) from [<c0133adc>]
(smpboot_thread_fn+0x178/0x190)
[ 4016.650000] [<c0133964>] (smpboot_thread_fn) from [<c013099c>]
(kthread+0x11c/0x138)
[ 4016.660000]  r9:cf8037e0 r8:cf802cdc r7:cf839df8 r6:cf803800
r5:00000000 r4:cf802cc0
[ 4016.670000] [<c0130880>] (kthread) from [<c0107218>]
(ret_from_fork+0x14/0x3c)
[ 4016.680000]  r10:00000000 r9:00000000 r8:00000000 r7:00000000
r6:00000000 r5:c0130880
[ 4016.680000]  r4:cf803800 r3:cf862000
[ 4016.690000] ---[ end trace 51114df08f429115 ]---

This is triggered by calling eth_schedule_poll(sw) after the IRQ has
been re-enabled.

Rework the network code to only enable IRQ's again if NAPI agrees it's
safe to do so.

Also only re-enable IRQ *after* cleaning up the RX ring and re-enabling
DMA, which otherwise resulted in ugly warnings regarding dirty page
fragments.
These popped up nearly immediately when building the kernel with O2 iso
Os.

--> Note that this change fixes stability issues, at the cost of ~8%
throughput performance.

While at it, also change the iface name being used in warning prints,
making it more obvious: "switch%d" --> "cns3xxx_eth"

The changes have been tested on 4 boards, each moving ~30TB of data

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte
9f54aaff70 cns3xxx: update patches for 4.14
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte
2543e7f08c cns3xxx: refresh kernel 4.14 config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte
0ef702c7e3 cns3xxx: copy patches for kernel 4.14
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Koen Vandeputte
809a265e35 cns3xxx: copy config for kernel 4.14
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Gabor Juhos
fbd33c2b6c ar71xx: fix format of the 701-MIPS-ath79-add-routerboard-detection patches
Commit e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAP
G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff
format, the unchanged, contextual lines must be preceded by a space
character.

Refresh the patches with quilt to fix them.

Fixes: e15c63a375 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Gabor Juhos
508999d366 ar71xx: fix format of the 741-MIPS-ath79-add-PCI-for-QCA9556-SoC patches
The patches introduced in commit 20e68f6d39 ("ar71xx: kernel: enable
PCI on QCA9556 SoC") have non standard format. In unified diff format,
the unchanged, contextual lines must be preceded by a space character.

Refresh the patches with quilt to fix them.

Fixes: 20e68f6d39 ("ar71xx: kernel: enable PCI on QCA9556 SoC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Gabor Juhos
bc178f6b15 ar71xx: mach-rbspi: simplify reset button registration
The setup code defines four individual structures for the
Reset buttons of the supported boards. The only difference
between the definitions is the GPIO number used for the
button.

Replace the different structures with one generic variant,
and add a helper function to simplify the button registration.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Koen Vandeputte
8954bc31ed imx6: add support for the intel gbit driver on GW5520
The Gateworks GW5520 board uses 2x intel gigabit mac's, instead of the
internal i.MX6 FEC.

Add support for these.

Signed-off-by: Scott V. Kamp <outbackdingo@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-01-17 11:07:17 +01:00
Pavel Kubelun
644a0d5403 ipq8065: adjust SS USB PHY power settings
According to QSDK ipq8065 has different SS USB PHY power settings.

Adjust it according to QSDK settings.

It also corresponds to oem Netgear R7800 tarball for soc ver >= 2.
eeac2e1019/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c (L2494)

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:05:11 +01:00
Pavel Kubelun
e93a16ed3f ipq806x: usb: add phy 1 master reset control
In current state only phy 0 master reset is controlled.
Add the phy 1 reset.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:04:57 +01:00
Pavel Kubelun
de748a121e ipq806x: usb: Control USB master reset
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3

Commit message:
"During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated."

Change-Id: I537dc810f6cb2a46664ee674840145066432b957
Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org>
(cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)"

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:06 +01:00
Pavel Kubelun
6617f3c6ab ipq806x: dwc3: Fix power_on and power_off sequence
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=d316437c9cdb70023a760342678f32e27241725a

The commit fixes:
- dwc3 phy module unloading
- possibly fixes FS#177 when some devices were improperly enumerated as HS while being SS thus stucking the driver during boot.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:06 +01:00
Pavel Kubelun
c263e18a53 ipq806x: Update HSIO recommended usb phy settings
Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=cf82fdf4bdd081cd81bb081f7815b915bc8bb851

The comit adjusts USB dwc3 phy default values as per QSDK recomendation and allows to set it through DT.

Commit message:
"SoC version based values will be recovered from the device node.
If device node does not have such values, defaults are applied.

Change-Id: Ia77b5b7fe95ce1a433885df1761091bced98d989
Signed-off-by: Gokul Sriram Palanisamy <gpalan@codeaurora.org>"

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:06 +01:00
Pavel Kubelun
a4c1767897 Revert "ipq8064: Fix dwc3 module unloading"
Preparing for proper fixes thus reverting commits:
- 8db079a9ff "ipq8064: Fix dwc3 module unloading"
- c75f059b0c "ipq8064: Fix dwc3 module unloading"

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:05 +01:00
Pavel Kubelun
7903a9219c ipq806x: update clk and cpufreq drivers
A newer clk and cpufreq drivers for ipq806x platform had been sent upstream.

A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing).

Following patches are removed:
 - 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer.
 - 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch.
 - 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:05 +01:00
Pavel Kubelun
83499bef73 ipq806x: force 2nd pci slot into gen1 mode
According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode.
EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode.

In previous commit we've added the support for this option, so enable it in DT for affected devices.

QSDK ref:
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506

While at it move the phy transmit termination offset value into dtsi file as it's platform specific.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:05 +01:00
Pavel Kubelun
36a96a4493 ipq806x: fix wireless regression
In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues.
https://bugs.lede-project.org/index.php?do=details&task_id=1197

This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch

Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant
Unfortunately qca developers do not bother to push it upstream.

Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration.

Fixes: FS#1197 and probably others
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2018-01-17 11:02:05 +01:00
Daniel Gimpelevich
e4442ca2d8 ramips: use blue status LED for Xiaomi Router 3G
The blue LED is what other firmwares use for this device, and it's a lot
easier on the eyes than its shade of yellow, which implies an error
condition.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[merge into existing $boardname:blue:status block]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>
2018-01-15 21:45:43 +01:00
Maxim Anisimov
5bdd238b63 ramips: add support for TP-Link Archer C20 v4
TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
  work.

Flash instruction:

The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-01-15 21:45:43 +01:00
Maxim Anisimov
ff1e895530 ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1
This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1"
because of TPLINK released new TP-Link Archer C20 v4. Additionally
migration to the generic board detection has been made.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-01-15 21:45:43 +01:00
David Bauer
6c56e968c1 ar71xx: fix TP-Link Archer C7 v4 switch LEDs
Match mapping of the switch LEDs according to the TP-Link
firmware behavior. LAN port 1 triggers the most right LAN LED,
LAN port 2 the second LAN LED from the right and so on.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-01-15 21:45:43 +01:00
Chen Minqiang
a8054d83dc ramips: add image checks
As long as we can't enforce image metadata, we need to use (platform)
image checks to have at least soem kind of validation.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-01-15 21:45:43 +01:00
Mathias Kresin
16f2befc3c ipq806x: drop ubifs support
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin
0af5e9bdc4 ipq806x: drop legacy image leftovers
Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin
52e7df3f49 ipq806x: unset filesystem specific build command by default
Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.

The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.

Fixes: FS#1276

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin
f319c5c254 ipq806x: remove unnecessary filesystem specific build
The Openmesh factory image doesn't need a squashfs specific build command.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Mathias Kresin
f2a8e02134 ipq806x: use bin file extension for sysupgrade-tar images
Use the file extension bin for sysupgrade-tar images to unify the file
extension across the target/tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-15 21:45:43 +01:00
Piotr Dymacz
030176e0e7 ar71xx: image: rework EnGenius ENS202EXT factory image
Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 13:39:54 +01:00
Jo-Philipp Wich
497f028da1 omap24xx: remove referece to not existing kmod-usb-musb-tusb6010
Remove leftover reference to a not existing kmod-usb-musb-tusb6010 from
the omap24xx target, the corresponding module is built into the kernel.

Fixes: 96815fe0a2 ("kernel: remove omap24xx specific kernel module packages")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-01-15 13:13:34 +01:00
Roger Pueyo Centelles
e15c63a375 ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.

See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9556
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
   · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
 - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
   PoE in

Working:
 - Board/system detection
 - Sysupgrade
 - Serial console
 - Ethernet
 - 2.4 GHz radio
 - 5 GHz radio
 - Reset button

Not working:
 - LEDs (added according to Mikrotik's GPL sources but not functional)

 Unsupported:
 - ZT2046Q SPI temperature and voltage sensor

Contributors: Giuseppe Tipaldi (@Ciusss89)
              Ricky (@rickydee)

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
2018-01-15 04:14:18 +01:00
Roger Pueyo Centelles
20e68f6d39 ar71xx: kernel: enable PCI on QCA9556 SoC
This patch enables the PCI bus on the QCA9556 SoC, the same way it is
done on the same family SoC QCA9558.

Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-01-15 04:14:18 +01:00
Piotr Dymacz
5352669c2c ramips: add support for ALFA Network AC1200RM
ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.

Specification:

- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers

Flash instruction (do it under U-Boot, using UART and TFTP server):

Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
2e5252d346 ar71xx: add support for GL.iNet GL-AR750
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
6cf682e214 ar71xx: image: move Sitecom WLR-8100 from legacy to generic
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Davide Fioravanti
a85db951db ar71xx: fix Sitecom WLR-8100 support
This patch fixes Sitecom WLR-8100:

- mtd layout
- LAN and WAN MAC address setup
- 2.4 GHz Wi-Fi MAC address setup
- 5 GHz Wi-Fi support (calibration data, MAC address setup, missing
  ath10k-* packages)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[squashed commits, fixed whitespace issues, reworded commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
af8f0629df ar71xx: add support for ALFA Network R36A
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.

Specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
1f06144cde ar71xx: add support for Teltonika RUT900
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.

There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.

This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector

Serial console pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:09:43 +01:00
Piotr Dymacz
4b0eebe9df ar71xx: add support for ALFA Network N5Q
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 21:30:16 +01:00
Piotr Dymacz
7f9f42d42e ar71xx: add support for ALFA Network AP91-5G
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB

Flash instruction:

Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Piotr Dymacz
ce6c7691ec ar71xx: base-files: cosmetic cleanups in preinit scripts
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Piotr Dymacz
9a867fcddf ar71xx: base-files: drop LED control from 05_set_iface_mac_ar71xx
There is no "dir-615-c1:green:wancpu" LED defined in mach-dir-615-c1.c

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Piotr Dymacz
71489bfa48 ar71xx: base-files: fix boards order in 05_set_preinit_iface_ar71xx
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00