Currently the maximum image size defaults to 8Mbyte even though this model has 16Mbyte of flash memory.
Tested and works on my device.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49129
- all subtarget specific defines are in their own files
- common defines left in main Makefile
- each subtarget makefile idefed with SUBTARGET
- all subtargets compile tested
- few seems to be broken/unneeded things marked with FIXME
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49104
1) Use leds to indicate:
Red - Power
Amber - Radio On
Blue - Wifi associated
2) Add profile to default build group for MT7628 subtarget
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
SVN-Revision: 49045
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.
SVN-Revision: 48994
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.
SVN-Revision: 48993
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.
SVN-Revision: 48992
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 48968
This patch adds profiles and support for building factory and
sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48906
This patch adds support for building factory and sysupgrade images
for the Netgear EX2700 that don't require modification of u-boot
environment variables.
The bootloader on this device expects the kernel partition to end
on a 64k block boundary. The last 64 byte of the kernel partition
must contain a valid uImage header - in the stock firmware, this is
the uImage header of the root filesystem. For this patch, we're using
the uImage header of a 0 byte partition (ex2700-fakeroot.uImage).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48771
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
SVN-Revision: 48721
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.
What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48698
The image name for the HiLink HLK-RM04 module has a typo and should read "RM04" rather than "RM02"
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48355
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
Use kernel arch for dts compilation.
Also use Image/BuildDTB to build dts for ramips.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47823
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
this device only works on top of UBI.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade
Tested and not working
* failsafe
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 47619
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47617
Add support for Dovado tiny AC wifi router.
Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports
5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47348
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Spaces -> Tabs
2: Removed some packages
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47113
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
SVN-Revision: 46921
This patch add support for Planex DB-WRT01. DANBOARD route on
the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
DANBOARD is Cartoon character.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46918
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46629
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46628
The following patch changes dts filename and profile name for Aigale Ai-BR100 (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46624
