Following the additions in r46924, enable the 'ext4' feature for
realview target so the ext4 image is created by default.
Signed-off-by: Dov Murik <dov.murik@gmail.com>
SVN-Revision: 47301
According to the info from NVRAM we should use port 8 for the CPU (and
interface eth2). Unfortunately it doesn't work right now, so lets switch
to the port 5.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Forwardport of r46586 from 15.05
SVN-Revision: 47281
Kernel 3.14 added aditional genphy_soft_reset phy reset to phy_init_hw in drivers/net/phy/phy_device.c
Since adm6996 does in driver soft reset and doesn't use BMCR_RESET for soft reset
add dummy soft_reset callback to adm6996 driver, like it is done in ar8216.
This fixes ticket #20147
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47272
Observed on ar71xx/ath79 platforms such as Ubiquiti RouterStations.Reported in #20642.:
(https://dev.openwrt.org/ticket/20642).
If embedded command-line text exists with CONFIG_IMAGE_CMDLINE_HACK=y,firmware
init doesn't initialize environment pointer (fw_init_cmdline not called).
arcs_cmdline is not initialized before calling strlcat.
Signed-off-by: Ted Hess <thess@kitschensync.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 47270
The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor
changes, it contains a newer revision of the QCA9533 SoC and the CPU clock
is significantly higher.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47263
ath9k expects to get revision id 2 for the QCA9531 ver. 2 rev. 0. This
fixes the very low TX power on some devices like the TP-LINK
TL-WR841ND v10.
As ath79_soc_rev is only used to get the revision number to ath9k on the
QCA9533, just set it to the expected value on the ver. 2.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Tested-by: Felix Kaechele <felix@kaechele.ca>
SVN-Revision: 47262
Antminers using the stock bootloader will not hash without this GPIO set.
Applies to DD and CC
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47261
This adds a basic implementation of clk_round_rate()
The clk_round_rate() function is called by multiple drivers and
subsystems now and the lantiq clk driver is supposed to export this,
but doesn't do so, this causes linking problems like this one:
ERROR: "clk_round_rate" [drivers/media/v4l2-core/videodev.ko] undefined!
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47254
These patches are written by Broadcom and will be in mainline Linux
kernel soon. I had some problems to get them backported to kernel 4.1,
so currently they are only available for 4.3.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47253
The files directory is now split up into the files which are needed for
every kernel version and the files only needed by kernel 4.1. The files
in files-4.1 are already merged into mainline kernel 4.3. This patch
only removed patches which were merged into mainline kernel 4.3.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47251
This replaces our SMP implementation with a very similar version which
is Broadcom currently trying to get into mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47247
Add device tree files for Broadcom Northstar based SVKs. Since the
bcm5301x.dtsi already exists, all that is necessary is the dts files to
enable the UARTs. With these files, the SVKs are able to boot to shell.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47246
This patch fixes ticket #15267 by enabling power on the
WNR2200's USB port. At present, the USB port on the WNR2200
is non-functional due to it not receiving power.
This patch defines an additional GPIO pin, but none of the
current GPIO definitions have been modified.
Signed-off-by: Riley Baird <BM-2cVqnDuYbAU5do2DfJTrN7ZbAJ246S4XiX@bitmessage.ch>
SVN-Revision: 47236
This patch supersedes the v1 from September 17th.
Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.
The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).
Fixed items:
- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.
Compiles fine, has been confirmed working by owners on 15.05.
Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?
Thank you
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 47234
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47221
This contains two sets of fixes for the 8139cp driver.
For all kernel versions older than 4.3, we can apply the fixes from the
4.3-rc4 kernel. In particular, these fix the TX timeout recovery which
is causing my Geos to lock up until the hardware watchdog kicks in.
For 4.0 and later kernels, we can also apply the additional improvements
which are going into 4.4 to fix and enable hardware checksum/TSO
offload. Backporting those to older kernels is non-trivial.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SVN-Revision: 47220
Still a lot of kernel-version ifdef'ery, but imho that's easy to remove
once obsoleted and avoids duplicate code in the meantime.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 47218
Whenever two processes were executing different commands at the same
time then one of the commands sometimes got the response of the other
command.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47213
This should help finding potential problems with the SPI driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47209
Until now the SPI driver used the TX bits for the RX FIFO. This seems
uncritical for now since both are equals on my devices (VR9), but this
could cause problems on other SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47208
This reverts commit 68c2e4789b4f071ee75d39248f4d08fe8283eb28.
commit r47159 was bad
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47207
add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960.
mt7620 is only compile tested.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47205
When talking to an atmel controller we need 9600 or 250000 baud.
as 250000 does not exist we use 2500000.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47204
* use build step mktplinkfw with extra arguments
* remove now unused mktplinkfw-chn-v2
* use Device/tplink
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47175
Allow to pass extra arguments to mktplinkfw step. Some board requires
an extra argument to create a valid image.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47174
These profiles covered by new image/Makefile descriptions. Only the old format uses
MultiProfile macro
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47173
This patch fixes a wrong non pre-emptive crc errors output of
dsl_control.sh status.
Signed-off-by: Luca Debernardi <luca.debernardi@gmail.com>
SVN-Revision: 47172
The device is similar to the TD-W8970, beside a different Atheros 2.4 GHz
wireless chip and the additional, PCI connected, WAVE300 5 GHz wireless.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47130
Port of r41856.
In contrast to the brcm63xx target, it isn't sufficient to enable/disable
the bridge. The device needs to be enabled/disabled to fix the hang. The
bridge will be automatically enabled by the time the connected device is
enabled.
Fixes boot on TD-W8980.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47129
This adds the changes from r46219 to the linux 4.1 patches as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47128
This way it's easier to configure device tree overlays, customize other
parameters...
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47126
Right now, selecting kmod-sound-soc-bcm2708-i2s causes build errors due to
missing configs.
kmod-regmap enables I2C and SPI, causing build errors due to depending
variables not defined.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47123
when sleep mode is disable use MIPS as clocksource and clockevent instead of systick.
because MIPS timer has higher resolution 5ns less than systick 20us and
larger counter bits 32 > 16.
clean interrupt by write compare register at isr.
fix typo cause sleep mode not enable.
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47122
Due to datasheet of rt3883 SoC rgmii1 port handles pins 84-95 and rgmii2 port handles pins 72-83. When this function ports gets added to rt3883_pinmux_data there's wrong pinmux bits set (RT3883_GPIO_MODE_GE1 manages 84-95 pins and RT3883_GPIO_MODE_GE2 manages 72-83). So when enabling rgmii2 as GPIO driver confuses hardware and nothing work, neither rgmii nor gpio.
Also in '0030-pinctrl-ralink-add-pinctrl-driver.patch' typo in name of rgmii2 port.
Signed-off-by: Nick Leiten <nickleiten@gmail.com>
SVN-Revision: 47118
The default switch frame size (with FCS + header) is 1536 bytes. But the
GMAC only accepted frames up to 1522 bytes. Setting it to 1536 allows to
receive ethernet frames using the full of MTU 1500 + an extra VLAN header +
VLAN header added by the switch.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47117
The driver assumes that the maximum received buffer for non-jumbo frames is
1536 bytes. But the allocation of the rx fragment doesn't reflect that. It
currently allocates fragments which will only be large enough to be used as
rx buffer with the size of 1534 bytes. This is problematic because the GMAC
will now try to write to 2 bytes which don't belong to its receive buffer
when a large enough ethernet frame is received.
This may already be a problem on existing chips but will at least become a
problem when the 1536 byte rx modus is enabled on MT7621a. It is required
on this SoC to receive ethernet frames which use their full 1500 bytes MTU
and a VLAN header next to the switch VLAN tag.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47116
The length of the DMA rx buffer was always set to 0 because the function
for extracting the length was used to calculate the value for setting it.
Instead the macro has to be split in a get and set function similar to the
TX_DMA_(GET_|)PLEN(0|1) macro.
No problem was noticed on MT7621a before this was changed and thus maybe it
was hidden by different problem which is not yet fixed.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47115
The MT7530 switch driver with enable_vlan set will automatically set all
ports to the user port mode. The hardware will remove the incoming vlan tag
on these ports and use it for its internal vlan. This is usually not wanted
and makes it impossible to communicate via vlan over the switch in both
directions.
It is possible to configure a switch port to "transparent mode" when this
port is only used as untag in the switch VLANs. This will disable the VLAN
untagging of packets when they were received on this port. The tagging on
"tag" ports based on the vlan id is still working.
The transparent port mode cannot be used when a port is both used in a VLAN
as "tag" and in another one as "untag" port.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47114
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Spaces -> Tabs
2: Removed some packages
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47113
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Merged most stuff into dtsi file
2: Remove unnecessary empty lines.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47112
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Fixed model order
2: Remove manufacturer name from model name
3: Use a hacky but prettier way to get mac address.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47111
Only add 'cuImage.tl-wdr4900-v1' to KERNEL_IMAGES if
the selected subtarget is 'generic'.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47109
