Commit graph

15886 commits

Author SHA1 Message Date
Alexander Couzens
aa930ba3dd lantiq: unmacro tp-link boards
even it's a little bit verbose, unmacrod board descriptions are much
easier to read and to understand.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-05 23:23:57 +02:00
Ash Benz
35c0328119 kernel/mtd: Add support for Macronix mx25u25635f, used in Archer C2600 v1.1
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-06-05 23:23:57 +02:00
Ted Hess
d0c6458339 ixp4xx: Drop linux 4.1 support
Signed-off-by: Ted Hess <thess@kitschensync.net>
2016-06-05 14:16:08 -04:00
Ted Hess
2ce19c0c1f ixp4xx: Add support for 4.4 kernel, refresh patches
Signed-off-by: Ted Hess <thess@kitschensync.net>
2016-06-05 14:07:46 -04:00
Álvaro Fernández Rojas
a0ea3eab63 brcm63xx: fix typo image/Makefile
This typo was introduced in c6990347

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-05 15:42:27 +02:00
Graham Fairweather
532c3f3218 brcm63xx: add initial support for Netgear EVG2000
This patch adds support for the Netgear EVG2000 VoIP Gateway to the
bcm63xx targets.

This device was not sold to the general public, but rather is/was
provided by telcos to customers in Sweden, Australia, Singapore and
other parts of asia.

Known issues:
 - Unable to detect 53115 switch. This appear to be a problem with
probing for the PHY using MDIO and results in error 5. Doesn't seem to
be a problem with the configuration, and could use someone with
experience to have a look at it.
 - Uses the b43 driver as using the OpenWRT/LEDE broadcom-wl driver
fails to load the firmware for the 4322, so 802.11n is not supported.

More info on the device and the research can be found at:
https://wiki.openwrt.org/toh/netgear/evg2000
https://wikidevi.com/wiki/Netgear_EVG2000
https://github.com/Xotic750/mirror-lede/tree/evg2000
https://forum.openwrt.org/viewtopic.php?id=63950

Signed-off-by: Graham Fairweather <xotic750@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 16:45:08 +02:00
Álvaro Fernández Rojas
a529b41cff brcm63xx: set DSL-274XB-F1 ath9k LED as active high
D-Link DSL-274XB rev F1 has an active high ath9k LED.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 16:40:51 +02:00
Álvaro Fernández Rojas
85a0a908e3 brcm63xx: set HG556a A/B ath9k LED as active high
Huawei HG556a has an active high ath9k LED.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 16:36:23 +02:00
Álvaro Fernández Rojas
7807c7e867 brcm63xx: add support for inverting ath9k LED polarity
Some devices with ath9k WiFi require changing the default active low
polarity to high in order to correctly operate the WiFi status LEDs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 16:35:46 +02:00
Álvaro Fernández Rojas
ec95509af4 brcm63xx: remove obsolote preinit scripts and fix preinit iface script
These scripts were causing ip issues in the latest version of LEDE:
https://gist.github.com/Noltari/6d20d8bcbe236caf516c0a73f5477d00

Fixes preinit iface script by making eth0 the default ifname and only changing
it to eth1 for the devices that specifically need it.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 16:30:06 +02:00
Álvaro Fernández Rojas
c69903473b brcm63xx: move profiles definitions to image/Makefile
This switches brcm63xx to the new profile definition system in image/Makefile

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 16:27:48 +02:00
Álvaro Fernández Rojas
2dc7f99662 brcm63xx: refresh kernel patches and config
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 16:25:18 +02:00
Álvaro Fernández Rojas
fd7786159d brcm63xx: drop linux 4.1 support
Switch to linux 4.4 now that it has been enough tested.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 16:25:11 +02:00
Álvaro Fernández Rojas
23273044a8 brcm63xx: switch to linux 4.4
Boot tested on AR-5381u, AR-5387un and WAP-5813n

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 16:25:04 +02:00
Álvaro Fernández Rojas
29b412b8c5 ramips: add kmod-pwm-mediatek for mt7628/mt7688
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 13:24:25 +02:00
Álvaro Fernández Rojas
604b92dbd0 ramips: fix the number of uarts for each SoC
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 12:20:33 +02:00
Álvaro Fernández Rojas
243e79e10c ramips: fix Mi Wi-Fi Nano Wireless LED pinmux
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-03 12:19:57 +02:00
Alexander Couzens
9efbf58360 omap: switch to 4.4
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-02 21:58:10 +02:00
Alexander Couzens
21208f5d43 linux/generic: add missing config symbols
unset following config symbols
- INPUT_PALMAS_PWRBUTTON
- INPUT_TPS65218_PWRBUTTON
- INPUT_TWL4030_PWRBUTTON
- INPUT_TWL4030_VIBRA
- INPUT_TWL6040_VIBRA
- KEYBOARD_TWL4030
- TWL4030_MADC

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-02 21:58:10 +02:00
Alexander Couzens
51f05b2d1a omap: take over maintainership
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-02 21:58:10 +02:00
Álvaro Fernández Rojas
a105eac4dd kernel: update kernel 4.4 to version 4.4.12
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-02 15:34:34 +02:00
Álvaro Fernández Rojas
794383b801 brcm63xx: fix F@ST2704V2 image generation
This device needs the firmware padded to 4MB.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-01 21:47:42 +02:00
Alexander Couzens
2a9f03adea ar71xx/image/edimax shorten the revision to 13 character
edimax fails if the revision is longer than 13 characters.
Also change the name from OpenWrt to LEDE

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-01 17:54:36 +02:00
Álvaro Fernández Rojas
65ae9db41a brcm2708: fix build error introduced in 2b4e5d47
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-06-01 17:11:04 +02:00
Yuan Chenmang
b38296f2f6 ramips: add Widora-NEO board support
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.

Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-06-01 12:52:28 +02:00
Stijn Segers
d2a91f9853
ar71xx: Fix TL-WR841N v11 LEDs, use separate machine
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-05-31 17:36:51 +02:00
John Crispin
1205e9a781 mediatek: more nand fixes
jffs2 failed to laod off nand

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-31 01:39:31 +02:00
John Crispin
9dafab92bf ipq806x: add a default profile
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-31 01:39:31 +02:00
John Crispin
1e152483de ipq806x: enable PM support
this fixes build errors with latest mac80211

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-31 01:39:31 +02:00
Joseph C. Lehner
2a589539ba ramips: fix Netgear EX2700 images
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-05-30 22:52:59 +02:00
John Crispin
0fa01e25ed ipq806x: remove accidentially comitted file
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-30 22:51:14 +02:00
John Crispin
21802f22f0 ipq806x: fix 3.18 support
accidentially removed the files in the v4.4 commit

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-27 22:28:15 +02:00
Daniel Gimpelevich
2b4e5d478b kernel: remove a hack that was obsoleted upstream
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Daniel Gimpelevich
492964e741 lantiq: Use correct macaddr generating logic for the DGN3500
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Daniel Gimpelevich
8b321d45be lantiq: Fix macaddr-setting code on DGN3500 and possibly other devices
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Daniel Gimpelevich
e8780b643b lantiq: Use the correct SPI flash speed for the Netgear DGN3500
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2016-05-27 16:08:47 +02:00
Alexander Couzens
8241479605 tools/tplink-safeloader: split CPE210 from CPE510 profile
The CPE210 was still described for the OEM upgrade as compatible,
even the wireless configuration isn't compatible anymore between
both series (2ghz and 5ghz).
Update the CPE210 image profile to use the new profile.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-27 15:55:13 +02:00
Alexander Couzens
b7864453f6 ar71xx: switch ordering and template to improve readability
The CPE210's ancestor is the CPE510 not the other way around. The device
profile is also named after the CPE510.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-27 15:55:06 +02:00
Joseph C. Lehner
b232669d45 ramips: fix Netgear EX2700 images
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2016-05-27 15:50:18 +02:00
Ash Benz
d517d8691a kernel/mtd: Add support for Macronix mx25u25635f, used in C2600 v1.1
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:18 +02:00
Ash Benz
cd36d71655 ipq806x/dts: Add Archer C2600 DTS
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
Ash Benz
7d963efc40 ipq806x/base-files: extract ath10k caldata
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
Ash Benz
14515cc271 ipq806x/base-files: Add support for Archer C2600
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
Ash Benz
98b50f0bef ipq806x/base-files: Add Archer C2600 LEDs and board
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
Ash Benz
ef02e8967c ipq806x: Add Archer C2600 to image/Makefile
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
Ram Chandra Jangir
5e49c57956 ipq806x: Add support for linux-4.4
1)Changes

- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime

2)Testing

Tested on IPQ AP148 Board:
 a. NOR boot and NAND boot
 b. ethernet network and ath10k wifi
 c. ubi sysupgrade

UnTested
 dwc3 usb has not been validated on IPQ board(AP148)

3)Known Issues:
 Once we flash ubi image on AP148, and if we reset the board, uboot on
 first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
 and not what linux expects which causes errors when trying to mount rootfs.
 In order to test this, we can use the below steps:
  a. Flash the ubi image on board and don't reset the board
  b. load the kernel fit image in RAM and boot from there.

Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>
2016-05-27 15:50:17 +02:00
Ash Benz
7eb1a7e956 include/image.mk: move build step tplink-safeloader to image.mk
Move tplink-safeloader from target/linux/ar71xx/image/tp-link.mk to include/image.mk

Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
Mathias Kresin
b2b917cd06 lantiq: do not build images which exceed the flash size
The user benpicco in #openwrt reported that images are build which are
bigger that the available flash size.

He provided a proof of concept fix and gave permission to me to send it
for inclusion.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
db66b157db lantiq: VGV7510KW22 - enable the IP101A phy
The RJ45 WAN port is used for xDSL as well as the IP101A.

The pins 1,2,3,6 of the RJ45 are connected to the IP101A and the
pins 4,5 are connected to the xdsl chip.

Drop the ip101a-rst node. It can't be controlled and is not required
at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
4d5db712e3 lantiq: VGV7510KW22 - fix pinmux configuration
The STP pinmux was initially added in assumption LAN2 led is driven by
it. It worked somehow because STP group and gphy0 led0 share the GPIO.
Do it the right way by adding the gphy0 led0 the gphy function.

According to the author, the SPI node is a copy & paste leftover. Which
makes sense since nothing is connected to the SPI bus on this device.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
a9f7586ad2 lantiq: VGV7519 - fix brn partition layout
Use the brnboot partition layout as it is listed in the OpenWrt wiki
article for this board.

Configure the brnboot root selector for this device as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
28faa3f292 lantiq: VGV7519 - get mac address from board_config partition
Use the mac address stored in the board_config partition instead of a
static one.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:17 +02:00
Mathias Kresin
1e395608cc lantiq: VGV7519 - add vlan support
Add the lantiq,switch property to enable vlans and setup them up.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:16 +02:00
Mathias Kresin
1deab53d88 lantiq: VGV7519 - add second usb port
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:16 +02:00
Mathias Kresin
79d92bb7ac lantiq: VGV7519 - cleanup pinmux configuration
Cleanup the pinmux configuration by removing the unused spi node. Nothing is connected to the SPI bus on devices.

The stp_out pinmux child node covers the same GPIOs as the already used
stp group.

The same applies to the gphy-leds_out pinmux node and the "gphy0
led1" as well as "gphy1 led0" groups.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:16 +02:00
Mathias Kresin
8a382f1221 lantiq: VGV7519 - remove/merge redundant parts in dts
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-27 15:50:16 +02:00
Mohammed Berdai
f778cdd9c9 lantiq: fix ARV4518PWR01 network
This patch fixes the missing Lan interface config in the file
/etc/config/network for ARV4518PWR01/A which results in eth0 and br-lan
being down and therefore no way to access the router unless via UART-TTL.

Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com>
2016-05-27 15:50:16 +02:00
Álvaro Fernández Rojas
2a57a54d49 ramips: add backported MT7628 pinmux fixes
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-05-29 11:26:41 +02:00
Cezary Jackiewicz
71e0ef3978 ar71xx: add GPIO pin for usb power switch for RouterBOARD 912
RB912 has one usb shared between external USB and miniPCIe slot. GPIO52 can
reroute power to external USB (=1) or internal miniPCIe slot (=0)

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-27 10:27:44 +02:00
John Crispin
7d67f79cb5 mediatek: more mtd fixes
this fixes full builds when ALL_KMODS is selected

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-25 04:42:54 +02:00
John Crispin
a42e84b2db lantiq: fix regression in VG3503J.dts
9d0608eef3 - "lantiq: VG3503J - merge profiles"

resulted in the dts file missing the version string.

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-24 17:17:36 +02:00
John Crispin
1eac53ba92 mediatek: update mtd backport
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-24 17:01:59 +02:00
Jo-Philipp Wich
52836866c9 kirkwood: add missing kernel symbol
The query for ARMADA_THERMAL is stalling the kconfig process and as long as we
do not package it, simply disable the symbol.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-05-24 19:41:27 +02:00
Jo-Philipp Wich
1012701014 x86: generalize partition discovery for sysupgrade
Generalize the partition discovery in sysupgrade in order to fix sysupgrade
and config backup/recovery on MMC block devices which use a different naming
scheme compared to mtdblock or sd* devices.

The change also adds the find applet to the ramdisk utilities so that upgrade
code can rely on it.

The commit is based on the initial submission by Russell Senior at
http://patchwork.ozlabs.org/patch/625440/ .

Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-05-24 13:30:58 +02:00
Cezary Jackiewicz
af1e70b4a7 ramips: Add status led for Xiaomi MiWiFi Nano
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-23 22:43:37 +02:00
John Crispin
bf6634339a ramips: fix timing issues when using MT7621 spi
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-23 20:22:22 +02:00
Claudio Leite
35782e104a mvebu: configure switch on WRT1200AC and WRT1900ACv2/S
Also collapses the three identical configurations into one block.

Signed-off-by: Claudio Leite <leitec@staticky.com>
2016-05-23 13:39:50 +02:00
Alexander Couzens
bf27ac019c ar71xx/cpe510: use second wifi calibration table
The cpe510 has two calibration tables. The first calibration
table requires to modify ath9k driver to work (patched tx gain table).

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:50 +02:00
Alexander Couzens
c5ff273d85 ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510
Split profile into 2GHz and 5GHz. The 5GHz devices are
quite "special". The 2 GHz works perfect.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:49 +02:00
Sven Eckelmann
f21de7d9a8 ar71xx: add MR1750v2 to the MR1750 profile
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:26 +02:00
Sven Eckelmann
c4e3706533 ar71xx: extract ath10k wifi board.bin for the OpenMesh MR1750v2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:26 +02:00
Sven Eckelmann
77cb985022 ar71xx: enable sysupgrade for the OpenMesh MR1750v2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:25 +02:00
Sven Eckelmann
58dc285cd6 ar71xx: add user-space support for the OpenMesh MR1750v2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:25 +02:00
Sven Eckelmann
f7719dca71 ar71xx: add kernel support for the OpenMesh MR1750v2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:25 +02:00
Sven Eckelmann
634f681da4 ar71xx: add OM2P-HSv3 to the OM2P profile
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:24 +02:00
Sven Eckelmann
222dfb3d6a ar71xx: enable sysupgrade for the OpenMesh OM2P-HSv3
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:24 +02:00
Sven Eckelmann
e10d12411c ar71xx: add user-space support for the OpenMesh OM2P-HSv3
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Sven Eckelmann
8010e8a370 ar71xx: add kernel support for the OpenMesh OM2P-HSv3
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Sven Eckelmann
823cea2d5d ar71xx: Allow OpenMesh CE images with more than 3 files
The CE image format used by OpenMesh can contain extra blocks which
are not used for flashing. Only the first three embedded images
(fwupgrade.cfg, kernel, rootfs) are required in this order to successfully
flash an image via sysupgrade. All extra embedded images should be ignored
for the available devices.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Sven Eckelmann
d1b4a8cfcf ar71xx: Move OpenMesh image target validation into subfunction
The platform_check_image_openmesh function used break statements to signal
that the board name matched the image target. This worked because the
sysupgrade binary checked the image inside a loop. The break statement
stopped the loop and skipped any additional check.

Instead the check should be done without such sideeffects by simply
combining the board names and image targets. Only a mismatch should cause a
negative result for the caller and skipping of the additional checks.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Sven Eckelmann
6150c15ad1 ar71xx: Generate sysupgrade images for OpenMesh devices
Some OpenWrt based firmwares like Gluon expect that a sysupgrade image
exists when a device firmware can be updated via sysupgrade. This image
wasn't created until now because OpenMesh devices use the same image for
factory and sysupgrade flash. Copying the image from *factory.bin to
*sysupgrade.bin is therefore enough to make the sysupgrade functionality
visible.

Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:22 +02:00
Sven Eckelmann
9b6b75d09d ar71xx: Add support for initramfs images for OpenMesh devices
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:22 +02:00
Felix Fietkau
f85e5e6778 ar71xx: move nand device image definitions to a separate file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-23 12:19:22 +02:00
Felix Fietkau
dcc2ea3cf5 ar71xx: move generic device image definitions to a separate file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-23 12:19:22 +02:00
Felix Fietkau
054df4fda4 ar71xx: split ubnt image building code into a separate file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-23 12:19:21 +02:00
Felix Fietkau
736fc38d33 ar71xx: split legacy image building code into a separate file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-23 12:19:21 +02:00
Felix Fietkau
64b8bb3b69 ar71xx: split tp-link image building code into a separate file
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-23 12:19:21 +02:00
Russell Senior
0fd183c155 x86_64: enable mmc to support booting off sd
Improved support for PCEngines APU

Signed-off-by: Russell Senior <russell@personaltelco.net>
2016-05-23 12:17:55 +02:00
Russell Senior
f89a20a89a ath25: update kernel from 3.18 to 4.4
Summary of changes:
	* moved config-3.18 to config-4.4 and patches-3.18 to patches-4.4
	* removed most of the first two patches, that seem to be upstream already
	* changed deprecated/removed IRQF_DISABLED to zero following examples in upstream kernel patches
	* added config line to disable device-tree to satisfy kernel configuration
	* add new image generation code

Build tested and run tested on an Accton MR3201A.

Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-23 11:56:38 +02:00
John Crispin
c7efbd7dbb ramips: Add specific compatible properties for esw
Currently, for RT5350 and MT7628, esw is marked as compatible with
"ralink,rt3050-esw". While this is true, the switches within RT5350
and MT7628 actually support more functionality than the RT3050 switch.

One such example is per-VLAN untagging, which is an important feature.

RT3352 is another example of this, but it already has an additional
compatible property, which allows to differentiate it from RT3050.

This commit adds such more specific properties for RT5350 and MT7628
as well.

Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
2016-05-23 11:28:59 +02:00
John Crispin
f5f173e2b7 mediatek: update patches
* fixes NAND
* adds latest ethernet patches

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-23 11:20:20 +02:00
Mathias Kresin
abfdddfb3c lantiq: VG3503J - use the 11G firmware
Use the 11G firmware for the phys as the oem firmware does.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-23 11:03:25 +02:00
Mathias Kresin
9d0608eef3 lantiq: VG3503J - merge profiles
The only difference between the VG3503J profiles is the version of the
gphy firmware that gets loaded. This can be handled perfect fine in one
device tree source file.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-23 11:03:24 +02:00
Mathias Kresin
21bdd79b33 lantiq: disable phy led complex (test) functions by default
They can be added using the phy led device tree bindings if required.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-05-23 11:03:23 +02:00
John Crispin
9e41c3f54e imx6: move profile definitions to the image/Makefile
Signed-off-by: John Crispin <john@phrozen.org>
2016-05-23 11:03:23 +02:00
Cezary Jackiewicz
2965430999 ramips: cleanup for Hame MPR-A2
- disable all ethernet ports except port 0 on MPR-A2

Port 0 is the only ethernet port on this router, so disable all other PHYs in order to save power.

- don't use a VLAN for the single ethernet port of the MPR-A2

Like A5-V11, this router only has one ethernet port.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-23 11:03:23 +02:00
Felix Fietkau
df98acc6a1 mvebu: backport upstream ethernet driver improvements and enable buffer manager support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-22 16:04:37 +02:00
Felix Fietkau
e90245237c oxnas: use global UBIFS_OPTS, all profiles use the same settings
Fixes build when selecting a device profile

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-22 15:58:41 +02:00
Felix Fietkau
848cacb21d mvebu: fix device I/O coherency issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-22 12:34:06 +02:00
Felix Fietkau
638a5682e1 kernel: remove bogus CONFIG_LOG_BUF_SHIFT overrides
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-21 22:35:41 +02:00