Restoring the config for kernel 3.14 didn't contain that change already
made to config-3.18.
It is needed to make squashfs in the kernel match the compression settings
for ARCH=arm in the framework.
If set to ARMTHUMB, boot fails due to squashfs being unreadable if the
filesystem was generated for wth ARM BCJ filter.
in include/image.mk: BCJ_FILTER:=-Xbcj $(LINUX_KARCH)
Thus the ARM filter is used for all ARM targets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43640
it should needs to depend on imx and mxs
also remove duplicate kmod definition from mxs target
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43627
The target au1000 has at least 2 different models, the
'InternetBox' and the 'MeshCube' which look very similar
from the kernel point of view but are totally different
devices which base on the same design. Populating /tmp/sysinfo
now. The 1st one has an issue which leads to a random
mac-address after each boot which is corrected now via
reading the bootloader-env. The real fix would be
converting to DTS, this is only a workaround now.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43626
This is required because it has to be called at very precise moment. See
comment in driver for details.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43611
similar to mv_sata, use nr-ports attribute from device tree.
import and adapt locking code from vendor GPL sources.
add dma controller handling, it may be used in future to avoid
full core resets similar to the vendor SDK's "progressive cleanup"
function.
this is still very dirty and aimed to first of all do things
quite exactly like the reference code. and it somehow works.
obviously there is lots of room for improvement :)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43598
sata_oxnas.c is obviously a refactored version of sata_ox820.c
which does contain this header.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43597
According to the vendor tarball, the TD-w8900GB's flash has 64k erase
block size, but CFE spans two blocks. So fixup the image offset
accordingly but keep block size at its default (64k).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: add commit message, add image offset, change nvram offset]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43572
This adds some updates to the NAND driver and refreshed the config.
Most of these changes are done in preparation for mainling it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43546
This adds some updates to the PCIe driver and refreshed the config.
Most of these changes are done in preparation for mainling it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43545
This brings ssb and bcma to wireless-testing tag master-2014-12-05
In addition it also adds the ARM-BCM5301X-Add-IRQs-to-Broadcom-s-bus-
axi-in-DTS-f.patch which adds the irq number in a way it is done in the
mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43544
I don't see that we're in an atomic context so there's no need to
busy-wait. Therefore replace the delay with sleep calls.
See also Documentation/timers/timers-howto.txt. It states:
"In general, use of mdelay is discouraged and code should
be refactored to allow for the use of msleep."
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43539
Replace the fixed wait time of 1s with polling for BMCR_RESET
to be cleared on all PHYs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43538
This reverts commit c81ddddde5fd193802d511b42eb7b108aac17136 on
https://gitorious.org/openwrt-oxnas/openwrt-oxnas.git
which removed patches and config for 3.14.
[arm_introduce-dma-fiq-irq-broadcast patch was renamed to match 3.18]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43520
similar to what was observed on kirkwood this significantly accelerates
btrfs write operations.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43498
gpio-beeper module was added to the kernel recently.
Make use of it to drive the piezoelectric buzzer of the kd20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43496
This is a swconfig driver for the Marvell 88E6171 switch,
which is a 7-port GigE switch with two CPU ports and 64
802.1q VLANs.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43486
Factor out set_mirror_regs to ar8xxx_chip.
Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43468
Factor out info whether switch should be configured at probe stage
to ar8xxx_chip. Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43466
Patch to add the buildprofile for the GL-Init-6408A-v1 and the GL-Inet-6416A-v1
Both devices are identical, only difference is one comes with 8MB flash and
the other with 16MB flash
Official website: http://www.gl-inet.com/w/?page_id=241&lang=en
Comprehensive list of specs: https://revspace.nl/GL-Inet
Signed-off-by: Martijn Zilverschoon <martijn@friedzombie.com>
SVN-Revision: 43462
Add the required nodes for the interrupt controllers and register
them through DT when a DTB is present.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43457
Add irq-domain aware irqchip drivers for the irq controllers of bcm63xx
and switch to use them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43454
At least on my Iomega ix2-200 system, this makes btrfs writes about 30% faster.
Signed-off-by: Richard Kunze <richard.kunze@web.de>
SVN-Revision: 43434
This patch introduces some code that is compiled in whenever
CONFIG_BRIDGE_NETFILTER is built, with the code called from code compiled under
CONFIG_BRIDGE, CONFIG_BRIDGE_IGMP_SNOOPING or CONFIG_BRIDGE_NF_EBTABLES.
Unfortunately, these options aren't setting explicitly the dependency they now
have on CONFIG_BRIDGE_NETFILTER, for obvious reasons for CONFIG_BRIDGE.
However, this is not working really well when CONFIG_BRIDGE_NETFILTER is built
as a module, since code statically compiled will now use a function that is not
in the kernel image, which makes the linker grumpy.
Solve this by removing the option to build CONFIG_BRIDGE_NETFILTER as a module,
and protect our function definition by an IS_BUILTIN instead of a IS_ENABLED
macro. This fixes the issue for CONFIG_BRIDGE and CONFIG_BRIDGE_IGMP_SNOOPING.
Fixing CONFIG_BRIDGE_NF_EBTABLES has to be handled a bit differently, since it
directly references a variable that will not be declared if
CONFIG_BRIDGE_NETFILTER is not set. Protect the variable affectations by an
ifdef to make sure this doesn't happen.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43419
This is the oxnas target previously developed at
http://gitorious.org/openwrt-oxnas
Basically, this consolidates the changes and addtionas from
http://github.org/kref/linux-oxnas
into a new OpenWrt hardware target 'oxnas' adding support for
PLX Technology NAS7820/NAS7821/NAS7825/...
formally known as
Oxford Semiconductor OXE810SE/OXE815/OX820/...
For now there are 4 supported boards:
Cloud Engines Pogoplug V3 (without PCIe)
fully supported
Cloud Engines Pogoplug Pro (with PCIe)
fully supported
MitraStar STG-212
aka ZyXEL NSA-212,
aka Medion Akoya P89625 / P89636 / P89626 / P89630,
aka Medion MD 86407 / MD 86805 / MD 86517 / MD 86587
fully supported, see http://wiki.openwrt.org/toh/medion/md86587
Shuttle KD-20
partially supported (S-ATA driver lacks support for 2nd port)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43388
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
With kernel 3.14 dts target p1010rdb was renamed to p1010rdb-pa.
To maintain compatibility define p1010rdb-pa as new standard and
copy p1010rdb.dts to p1010rdb-pa.dts under 3.10.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43371
If there is no board support in the kernel, it does not make sense to
build images for devices. So drop any images for board ids for which
there are nc corresponding board_info structs in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43364
Patch reverts 43332 which seems to cause issues with VLAN functionality.
Add a specific check to check whether ANEG is still enabled and re-enable
it if necessary. Disable generic phy soft reset for kernel >=3.16.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43356
This target can be emulated using ARM's Foundation_V8 simulator
software or qemu-system-aarch64 using the command-line described in the
README file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43355
Move compatible strings from board structs into separate table. This
allows for several board compatibles to match to the same board in case
e.g. only the flash size / partitions differ.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43341
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43334
Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43333
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43332
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43331
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43330
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43329
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43328
wg302v1_fixup() looks for the ATAG_CMDLINE atag, it doesn't find it and
so it takes the last atag in the list and overwrites non allocated
memory.
The side effects are corrupted vital data and a kernel that doesn't
boot. More details here https://dev.openwrt.org/ticket/18356
The fix appends the fixup to the command line and updates the atag only
when it finds it.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43320
Few notes:
- redboot partitions are unusable
- redboot declares only 16M of RAM, hence the mem arg in cmdline and separate kernel config
- boots fine but only ethernet works for now
- split wiliboard and raidsonic boards into different subtargets
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 43319
This patch adds 3.14 kernel support for the mpc85xx platform.
Works fine here with a TL-WDR4900 which seems to be the only
supported device using this platform.
There might be differences depending on HW version, therefore
I'd ask others to test too.
Changes to 3.10
missing config options added to 3.14 config file
patch 001: rebased
patch 100: rebased
patch 110: rebased
patch 120: rebased
patch 130: rebased
patch 140: minor adjustment
patch 200: removed, change went upstream
patch 210: rebased
patch 220: removed, change went upstream
patch 750: new, fixes an issue with ethernet port autoneg being
disabled due to changes in kernel phy handling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43308
still no sound but the codec is properly detected now, powers up and i can hear
noise on the speakers.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43305
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43303
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43301
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43292
Without this patch the UBIFS driver is unable to attach to the mtd
storage and mount the root FS.
Fixes a kernel panic with Netgear WNDR4300/3700v4 devices.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43287
the SDK does a bit of extra init that we did not do yet when using an external mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43245
* read MAC address from factory partition
* remove port defines since there is only one port (most likely C/P error)
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 43231
r43200 tries to detect if the fixup is needed or not. control the behaviour via
OF instead and disable unused ports.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43201
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
Add patches for getting the IRQ number for a device of the bcma bus
that were send for upstream inclusion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43148
The patch adding AR8216_PHY_LEDS was not ported to more recent kernel
versions.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43139
Some changes from the header file were not ported from older kernel.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43137
The select SYS_HAS_DMA_OPS in CPU_CAVIUM_OCTEON was from the kernel
patch in 3.13, but it is only included in kernel 3.14 and not in 3.13
and 3.18, add it again.
Thank you swalker for spotting this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43134
some bootloaders (linksys e1700) set wonky hw trap values. reset this upon boot to make all ports work.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43117
OpenWRT patch 255-lib80211_kconfig_hacks gives user possiblity to select
LIB80211 dependant settings (LIB80211_CRYPT_*) without having LIB80211
selected which is wrong.
My patch changes OpenWRT patch so LIB80211 is vissible and all
LIB80211_CRYPT_* options selects LIB80211 automatically.
Signed-off-by: Tomasz Wasiak <tjwasiak@gmail.com>
SVN-Revision: 43112
Change list:
* add tx scatter gather function.
* add software rx vlan offload to let GRO work.
* add jumbo frame support. because use build_skb so max MTU is 3812.
* enable hardware tx vlan.
* enable GRO and remove LRO. because it can improve performance and can work on forwarding.
* enable/fix tx padding function.
* let napi handle tx clean up.
* support ethtool operation. now support message level, hardware status and coalesce.
* ethtool support use mdio to get phy status only on mt7620. need modify dts file and add phy info to support it.
Notes:
* build and test on rt2880, rt3052, rt3352, rt3662, rt5350 and mt7620a.
* TCP NAT performance improve. test with netperf.
- rt2880(gigabit) from 5x to 12x Mbps.
- rt3x5x from 6x to 94 Mbps.
- rt5250 from 5x to 8x Mbps.
- rt3662(gigabit) from 6x to 42x Mbps with GRO. 23x Mbps without GRO. 66x Mbps with jumbo frame.
- mt7620 still 94Mbps.
* TSO function not tested. because i don't have mt7620 with eco >= 5. and the hardware don't support to set MSS. it will have problem.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43108
Boards that have more than one swconfig enabled switch will show the devices in
reverse order when call swconfig list. Fix this by using list_add_tail().
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43106
0x8100000c vs 0x810000c0 int he pvc register this caused the cascade with an external mt7530 to fail.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43104
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
SVN-Revision: 43102
lantiq_dsl.sh didn't work with VDSL chipsets for now, fix that by
detecting whether vdsl_cpe_control or dsl_cpe_control should be used.
Also add missing quotes around shell string comparision.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43101
This works around a bootloader issue where every device
has the same lan/wan-mac 00:04:9f:ef:01:01 - with this patch
we read the macs from config-partition during initial network
setup. We have 9 valid macs stored in the partition, the
1st two are used for the radios, 3 and 4 are now used for WAN/LAN.
on an already setup / running device we can get the real macs with
. /lib/functions.sh
. /lib/functions/system.sh
echo "LAN = $(mtd_get_mac_binary config 338)"
echo "WAN = $(mtd_get_mac_binary config 344)"
see:
https://dev.openwrt.org/ticket/14714
from the ticket / user klondike:
U-Boot passed this commit ecd1a09b81http://u-boot.10912.n7.nabble.com/U-Boot-PATCH-mpc83xx-remove-hardcoded-network-addresses-from-config-files-td44372.html
I suppose to prevent this particular issue, but the WDR4900 may be using an old bootloader still affected.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
I have been checking the contents of the dtb on the flash, this particular bit is quite revealing:
ethernet@b0000 {
#address-cells = <0x1>;
#size-cells = <0x1>;
device_type = "network";
model = "eTSEC";
compatible = "fsl,etsec2";
fsl,num_rx_queues = <0x8>;
fsl,num_tx_queues = <0x8>;
local-mac-address = [00 00 00 00 00 00];
^^^^^^^^^^^^^^^^^
interrupt-parent = <0x2>;
phy-handle = <0x3>;
phy-connection-type = "rgmii-id";
ptimer-handle = <0x4>;
queue-group@0 {
#address-cells = <0x1>;
#size-cells = <0x1>;
reg = <0xb0000 0x1000>;
rx-bit-map = <0xff>;
tx-bit-map = <0xff>;
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
};
};
I also have been checking the live device map to find this:
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b0000/local-mac-address
00000000 00 04 9f ef 01 01 |......|
00000006
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b1000/local-mac-address
*
root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b2000/local-mac-address
*
My conclussion is that U-Boot most likely finds the device and (as no valid MAC-address is provided)
falls back to the default MAC provided by the old code, the kernel then receives thee modified
device map from U-Boot and assumes this is the correct MAC for the device despite it obviously isn't.
This can be seen at
target/linux/mpc85xx/patches-3.10/140-powerpc-85xx-tl-wdr4900-v1-support.patch
The enetaddr is filled up by using the device tree data by the process_boot_dtb
function and used by the platform_fixups function to set the eth0 address
(by calling dt_fixup_mac_address_by_alias("ethernet0", enetaddr); ).
But instead we should be used the device address which to my understanding is
provided in the mtd.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43074
All platforms which are using 3.10.x at the moment are upgraded.
Changelogs:
https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.50https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.51https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.52https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.53https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.54https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.55https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.56https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.57https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.10.58
A new symbol 'X86_16BIT' appeared in 3.10.52 with commit 34273f41d57ee8d854dcd2a1d754cbb546cb548f
("x86-espfix-make-it-possible-to-disable-16-bit-support.patch")
I defaults to 'unset', but it's worth a discussion to enable it
("turn off support for any 16-bit software").
Also removed the patch 0db3db45f5bd6df4bdc03bbd5dec672e16164c4e
("fix build failure on memcpy() in decompress.c")
and is obsolete by commit 29593fd5a8149462ed6fad0d522234facdaee6c8 upstream.
included in kernel 3.10.56
compile tested on all platforms with:
make tools/install
make toolchain/install
make target/linux/compile
user@box:~/user/openwrt$ cat /tmp/log.txt
[Wed Oct 22 00:36:02 CEST 2014] ./smoketest.sh: ar71xx - OK
[Wed Oct 22 00:53:22 CEST 2014] ./smoketest.sh: ar7 - OK
[Wed Oct 22 01:08:27 CEST 2014] ./smoketest.sh: au1000 - OK
[Wed Oct 22 01:21:43 CEST 2014] ./smoketest.sh: avr32 - OK
[Wed Oct 22 01:37:47 CEST 2014] ./smoketest.sh: cns21xx - OK
[Wed Oct 22 01:52:05 CEST 2014] ./smoketest.sh: cns3xxx - OK
[Wed Oct 22 02:10:23 CEST 2014] ./smoketest.sh: gemini - OK
[Wed Oct 22 02:29:07 CEST 2014] ./smoketest.sh: ixp4xx - OK
[Wed Oct 22 02:44:01 CEST 2014] ./smoketest.sh: malta - OK
[Wed Oct 22 02:55:57 CEST 2014] ./smoketest.sh: mpc85xx - OK
[Wed Oct 22 03:07:56 CEST 2014] ./smoketest.sh: orion - OK
[Wed Oct 22 03:24:30 CEST 2014] ./smoketest.sh: ppc40x - OK
[Wed Oct 22 03:40:19 CEST 2014] ./smoketest.sh: ppc44x - OK
[Wed Oct 22 03:55:29 CEST 2014] ./smoketest.sh: realview - OK
[Wed Oct 22 04:09:47 CEST 2014] ./smoketest.sh: sparc - OK
[Wed Oct 22 04:23:37 CEST 2014] ./smoketest.sh: x86 - OK
[Wed Oct 22 04:35:56 CEST 2014] ./smoketest.sh: xburst - OK
run tested on x86, au1000, ar71xx, mpc85xx and brcm47xx
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43049
replace all occurences of LINUX_VERSION with the cleaner
approach. future kernel upgrades must mostly touch only
one file. the only platform left is netlogic, because it
uses a intermediate kernel 3.14.16
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43047
This is required due to 306-mips_mem_functions_performance.patch, just
add a memmove() implementation to satisfy the lzma2 decompressor code.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43036
According to the ticket #18152 it also uses NAND with 0x20000 erase size
and 0x800 page size.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43008
Fix sysupgrade to determine the correct boot block device to use if
/proc/cmdline contains a PARTUUID root.
Change the preinit move_config() hook to use the UUID scanning code
from sysupgrade in order to avoid code duplication.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42968
Enable the required squashfs and block2mtd support in the kernel in order
to be able to actually boot them.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42967
If the underlying block device is a USB device it might require some
time to settle, observed when booting a squashfs image from sd card
on an Alix APU board.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42966
