Commit graph

40830 commits

Author SHA1 Message Date
Piotr Dymacz
54b1be5f91 ar71xx: image: simplify Embedded Wireless definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
a679a45f0e ar71xx: image: generic: use simply expanded variables
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
3bc017fa3c ar71xx: image: generic: clean up trailing whitespace
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Ding Tengfei
e07014e70b ar71xx: add support for COMFAST CF-E355AC v2
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9886.

Short specification:

- 2x 10/100 Mbps Ethernet, with PoE support
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[updated kernel config for both boards]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Sven Eckelmann
b1d57dadb2 ar71xx: disable 40Mhz refclk for QCA953x
The "QCA9531 v2.0 802.11n 2x2 2.4 GHz Premium SOC for WLAN Platforms"
datasheet (80-Y7991-1 Rev. C - October 2014) doesn't specify support for a
40 Mhz reference clock. The register description for "Bootstrap Options"
(page 31) defines following states for the bit 4 (REF_CLK):

* 0 - CLK25 (default)
* 1 - (reserved)

Devices like the TP-Link CPE210 v2 has this bit set to 1 but is using a 25
Mhz reference clock. OpenWrt is still interpreted this bit as 40 Mhz and
then break the bootup of the system due to this incorrect interpretation.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
[refreshed patches]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
c6bd0b4894 uboot-envtools: add support for WHQX E1700AC/E600G/E600GAC v2
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Peng Zhang
d8e6c3f6d9 ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2
WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11)
- 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 1x USB 2.0
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (J5) and LEDs (J13) headers on PCB

WHQX E600G is based on Qualcomm QCA9531.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB

WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11)
- 2x 10/100 Mbps Ethernet
- 6x LED (1x RGB, 5 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-12 V)
- UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB

Important notice:

First version of these boards are using different mtd layout, with ART
data at the end. You should not use v2 images on v1 board because it
will result in lost of ART data!

Flash instruction (using U-Boot CLI and tftp server):

1. Configure PC with static IP 192.168.1.10 and tftp server.
2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
3. Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
4. Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
3. Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[reworked: image generation code, mach-* files, commit description,
fixed minor code style issues, rebased on master]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
fc43e7a6e0 ar71xx: fix typos and indentation in Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Kyson Lok
bb1df2d75b ar71xx: include vendor name for GL iNet products
This patch include GL.iNet vendor name in the
machine name for GL.iNet vendor products.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
2018-02-22 18:53:22 +01:00
Kyson Lok
9dbfd8e9df ar71xx: uniform GL iNet products mach name
The mach name of GL AR150 and GL AR300 is inconsistent
with other products.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
2018-02-22 18:53:21 +01:00
Roman Yeryomin
6b6dc2b3e3 ramips: mt7621: fix usb init
In 4.14 reg-names is required to identify resources.
Otherwise init fails with:

[    5.900501] xhci-mtk 1e1c0000.xhci: invalid resource
[    5.910499] xhci-mtk: probe of 1e1c0000.xhci failed with error -22

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-02-22 17:25:38 +01:00
Felix Fietkau
848a4abf27 ath9k: merge a RCU fix for station tx cleanup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 15:37:59 +01:00
Felix Fietkau
94a3af88f3 octeontx: remove lots of bogus kernel config overrides
Some of them break when building with all modules enabled

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 13:12:17 +01:00
Tim Harvey
9f2c769a59 kernel: add missing symbol
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey
d83ce3ff50 octeontx: remove undefs of CONFIG_NET_VENDOR_*
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey
b63b18dffc octeontx: remove unnecessary CONFIG_DEBUG_INFO
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey
ef627cb0f5 octeontx: add fpu support
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey
10280d9e22 octeontx: remove CFLAGS
You should not define CFLAGS for the toolchain as this will also leak
into other targets if they share the same toolchain.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey
c0470e7917 octeontx: add FAT FS support to kernel
The CN80XX Boot firmware uses an embedded FAT12 filesystem. For some reason
busybox can't mount this unless its enabled static in the kernel.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Tim Harvey
4294b79e0a octeontx: add USB_PCI support
The CN80XX XHCI is supported through PCI

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2018-02-22 13:12:06 +01:00
Koen Vandeputte
efb362cd93 imx6: disable dma on uart
When this target got updated to 4.14, this patch got removed to
re-evaluate if it was still needed.

Extensive testing now shows this issue is still present.
Let's re-add the patch to fix it for now.

As the uart bus is very low bandwidth .. performance impact is negligible.

Boot log:

[   22.513051] imx-uart 2020000.serial: DMA transaction error.
[   22.522721] imx-uart 2020000.serial: DMA transaction error.

As a sidenote:
The patch mentiones an issue with RS485, but the bootlog
errors above were recorded with the uart ports in standard RS232 mode.

Compile/Run-tested on imx6/GW5200

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-22 12:46:49 +01:00
Koen Vandeputte
aad1f11efe kernel: refresh patches
Some fuzz was introduced due to the netfilter-offload series

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-02-22 12:46:25 +01:00
Felix Fietkau
14a01311f5 kernel: remove kmod-appletalk
This has been obsolete for many years now and has been implicated in a
recent build failure

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 12:08:38 +01:00
Felix Fietkau
ecd810d0f5 kernel: fix kernel module packaging errors on imx6
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 11:58:00 +01:00
Felix Fietkau
1b13cbc15b grub2: disable building platform code for target utility
It is not used and it was causing a build error with GCC 7.3

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-22 09:30:22 +01:00
Felix Fietkau
7a97588bc6 toolchain/gcc: use version 7.x for x86 by default
This is needed for retpoline support, which mitigates the spectre
attacks.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:57:30 +01:00
Felix Fietkau
65ae02d602 toolchain/gcc: remove unused config symbol
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:57:24 +01:00
Felix Fietkau
9d2a23780e kernel: avoid stripping retpoline flag with CONFIG_MODULE_STRIPPED
Fixes kernel warning when loading modules

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:55:52 +01:00
Felix Fietkau
820f030998 netfilter: add a xt_FLOWOFFLOAD target for NAT/routing offload support
This makes it possible to add an iptables rule that offloads routing/NAT
packet processing to a software fast path. This fast path is much
quicker than running packets through the regular tables/chains.

Requires Linux 4.14

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:42 +01:00
Felix Fietkau
1033356442 kernel: backport netfilter NAT offload support to 4.14
This only works with nftables for now, iptables support will be added
later. Includes a number of related upstream nftables improvements to
simplify backporting follow-up changes

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:42 +01:00
Felix Fietkau
b7265c59ab kernel: backport a series of netfilter cleanup patches to 4.14
Preparation for backporting upstream NAT offload support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:42 +01:00
Felix Fietkau
bc3e0f6052 nftables: update to 0.8.2, backport flowtable support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:41 +01:00
Felix Fietkau
8cdc71fc92 libnftnl: backport flowtable support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 20:12:41 +01:00
Felix Fietkau
c8d07575e5 mac80211: add minstrel improvements/fixes
- Simplify debugfs code
- Reduce size
- Fix handling of CCK rates

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:29:33 +01:00
Felix Fietkau
981cca12b6 hostapd: add support for sending 802.11v disassoc imminent notifications to clients via ubus
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:29:09 +01:00
Felix Fietkau
01b2c0fc49 hostapd: add support for issuing 802.11k beacon measurement requests via ubus
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:29:04 +01:00
Felix Fietkau
21bb42fb8a hostapd: expose client 802.11k capabilities via ubus
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:28:59 +01:00
Nick Hainke
e2681eb06a hostapd: return with 80211 codes in handle event function
If the auth or assoc request was denied the reason
was always WLAN_STATUS_UNSPECIFIED_FAILURE.
That's why for example the wpa supplicant was always
trying to reconnect to the AP.
Now it's possible to give reasoncodes why the auth
or assoc was denied.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2018-02-21 19:28:56 +01:00
Lorenzo Santina
83b4fa9b3b hostapd: add IEEE 802.11v support
Add Wireless Network Management (IEEE 802.11v)
support to:
- hostapd-full
- wpa_supplicant-full

It must be enabled at runtime via UCI with:
- option ieee80211v '1'

Add UCI support for:
- time_advertisement
- time_zone
- wnm_sleep_mode
- bss_transition

Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
2018-02-21 19:28:50 +01:00
Felix Fietkau
6b1816f8a3 hostapd: add support for turning on 802.11k/v features via ubus
Neighbor reports are enabled implicitly on use, beacon reports and BSS
transition management need to be enabled explicitly

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:28:43 +01:00
Felix Fietkau
526921f20e mac80211: round up tx status headroom
Fixes unaligned access exceptions in mt76 when transmitting beacons

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 19:28:36 +01:00
Felix Fietkau
8a59f9590e ramips: fix MT7621 switch driver IRQ storm on init with linux 4.14
The hardware emits some interrupts while initializing and handling them
can mess up the state or cause infinite loops.
Fix this by disabling IRQs during init and re-enabling them afterwards

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 14:46:45 +01:00
Felix Fietkau
0405205140 kernel: fix MIPS GIC clock source counter width (affects MT7621)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 14:46:45 +01:00
Felix Fietkau
79f9cadd00 ramips: fix MT7621 PCI driver on 4.14
The .map_irq hook can now be called after init.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-21 14:46:45 +01:00
Felix Fietkau
9595a9e8d3 kernel: fix return value of usb_xhci_needs_pci_reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-20 22:29:32 +01:00
Felix Fietkau
c38fb58576 kernel: fix disabling common usb quirks on 4.14
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-20 22:19:41 +01:00
John Crispin
3cb38368e2 ubox: fix PKG_MIRROR_HASH
Signed-off-by: John Crispin <john@phrozen.org>
2018-02-20 21:35:14 +01:00
INAGAKI Hiroshi
e1d4aa36b0 ramips: add support for Tama W06
Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek
MT7688AN.

Specification:

- MT7688AN (575 MHz)
- 64 MB of RAM (DDR2 SDRAM)
- 16 MB of Flash (SPI)
- 1T1R 2.4 GHz
- 1x 10/100/1000 Mbps Ethernet
- 4x LEDs (GPIO connected: 3), 1x button
- 1x USB 2.0 Type-A (host)
- UART header on PCB (GND, RX, TX, Vcc from RJ45 side)

Flash instruction using sysupgrade image:
1. Connect micro-USB cable for power supply into W06 and turn on the
router
2. Connect to wifi with SSID "tama-*" with password. Complete SSID and
password are listed on the back of the router
3. Access to 192.168.1.1 and login with user name "admin" and password
empty
4. In firmware update(ファームウェア更新) page, click "参照" button
and click "ブラウザー" button to open file browser, select the
sysupgrade image and press OK button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-02-20 19:25:17 +01:00
Mathias Kresin
cb741654e5 ramips: improve GnuBee Personal Cloud Two support
Use the generic board detection for the GnuBee Personal Cloud Two
instead of the target specific one as all recent additions are doing.

Fixup the pinmux to set all pins used as GPIO to the function GPIO.
Request pins where used.

Drop the i2c from the dts. There is nothing connected. While at it fix an
indentation issue and use references instead of duplicating the whole
node path.

Use the same switch config as for the GB-PC1 and drop the led trigger for
the not supported IP1001 phy connected to second rgmii.

Fixes: c60a21532b ("ramips: Add support for the GnuBee Personal Cloud Two")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
c330408ea9 ramips: use generic board detection for D-Link DAP-1522 A1
Use the generic board detection for the D-Link DAP-1522 A1 instead of the
target specific one as all recent additions are doing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00