This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)
Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
- RAM: 64MB DDR
- Storage: 16MB NOR SPI flash onboard
- Omega2+
- RAM: 128MB DDR
- Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
- All Docks Provide:
- Micro-USB port to provide power to the Omega
- On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
- USB 2.0 socket connected to Omega
- Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
- Omega GPIO breakout
- Allows for connection of Omega Expansions:
- Ethernet Expansion
- Relay Expansion
- PWM Expansion
- OLED Expansion
- Ethernet Expansion
- Proto Expansion
- Cellular Expansion
Signed-off-by: Lazar Demin <lazar@onion.io>
Fixes build failure for kmod-can-c-can-platform which depends on
kmod-regmap for kernel 4.1 and 4.4.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to /files, /overlay is only useful for modifications not tracked in
the LEDE repository itself.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This patch updates the QCA988X firmware to the latest revision
firmware-5.bin_10.2.4-1.0-00016
found in the official ath10k-firmware repository.
Tested on TP-Link Archer C7 v2.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Host files installed in Build/InstallDev are target-specific and will stay
in $(STAGING_DIR)/host after the STAGING_DIR_HOSTPKG unification.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Make sure binaries install to STAGING_DIR_HOSTPKG are still found when
this variable is eventually modified.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Packets which are merely forwarded by the router and which are neither
involved in any DNAT/SNAT nor originate locally, are considered INVALID
from a conntrack point of view, causing them to get dropped in the
zone_*_dest_ACCEPT chains, since those only allow stream with state NEW
or UNTRACKED.
Remove the ctstate restriction on dest accept chains to properly pass-
through unrelated 3rd party traffic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Unify switch configuration on Linksys WRTxx00AC series.
LAN = eth0, WAN = eth1
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[Álvaro]: also change WAN LEDs
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This reduces the amount of hacks in the makefile code.
Remove the apm821xx code to do the same - it was broken and left both
compressed and uncompressed images in $(BIN_DIR)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use ubus process signalling instead of 'kill pidof dnsmasq' for
SIGHUP signalling to dnsmasq when ntp says time is valid.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
It could cause crashes with some forms of virtualization, and it is
unlikely to work properly with most systems.
It's safer to just disable it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The generated 'its' is passed to mkimage which expects linux arch
strings rather than the full arch (e.g. mips not mipsel).
It currently works in some cases where LINUX_KARCH == ARCH but
otherwise you get an unknown arch build error.
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There's a GPIO that can switch between power to USB pins for the
internal MiniPCIe slot or the external USB port.
People are more likely to use the external one so enable it by default.
Existing configurations should be unaffected
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This should hopefully fix build issues where libraries that we ship in
tools/ were accidentally picked up from other places on the system, e.g.
/usr/local
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Is it used by VMware Fusion by default. This allows images to boot
without further config changes in VMware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Most mac80211 drivers leave the SMPS field in the HT capabilities
uninitialized (unfortunately defaults to static SMPS), which leads to
some devices limiting themselves to single-stream rates in some modes
(mostly mesh and IBSS).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
