The GW16083 Ethernet Expansion Mezzanine adds the following to supported
Gateworks baseboards:
* 7-port Ethernet Switch
* 4x RJ45 ports (ENET1-4) supporing 802.11af/at PoE (with optional PoE module)
* 2x RJ45 ports or SFP module (ENET5-6) (auto-selected)
This series adds support for a phy driver that adds support for ENET5/ENET6
PHY adding initialization for those PHY's and a polling mechanism that detects
SFP insertion and configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42147
The GW16082 miniPCI Expansion Mezzanine has the INTA/B/C/D IRQ's reversed
from the PCI standard. This will soon be resolved in the bootloader via
devicetree, but in the meantime this will work around the issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 42146
Now that we migrated all users to dtb based detection, we can drop the
board fixup code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42129
This requires individual images for each board version for now.
Linux partition was shrunk to ensure writing thewrong image won't
erase wifi calibration data.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42126
Add the required nodes to the dtsi files and code to prevent double
registration from the board support code.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42123
In preparation for switching to dtb based board identification, add
support for building lzma-loader and lzma cfe kernels with dtb
appended.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42121
Allow appending a dtb blob to the binary and use it for identifying the
board. Fall back to nvram based identification in case of no dtb passed.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42119
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42088
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 42083
In r41578 this was added in order to make default images bootable for the BB
release. We need more generic approach for this.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 42071
Apparently this is a fairly common refurb unit of the 3800 series now,
with merely the recognition string changed in the boot loader.
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
SVN-Revision: 42023
This changeset implements a new menuconfig option to generate separate
repositories for each enabled package feed instead of one monolithic one.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 42002
Created on basis of 3.10 config. Remove few obsolete symbols and add new
upstream symbols. New symbols left in its default state.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41996
Change list:
* Remove button info on GPIO12, there is no button there.
* Remove nvram mtd partition, as it's not used for anything, saves 64k for user data.
Tested building for carambola2 target.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
SVN-Revision: 41993
Fix IFF_NO_IP_ALIGN location which is collide with new netdev private flag
IFF_MACVLAN.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41992
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.
Signed-off-by: Lintel <lintel.huang@gmail.com>
SVN-Revision: 41961
This commit implements a new netfilter match "xt_id" which can be used to
attach unsigned 32bit IDs to iptables rules.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 41945
Mostly works except for USB led. Flashing not tested yet. Mostly
as an example for the sprom fixup code.
Fixup values taken from GPL tarball by comparing bcm43217_map.c
with the struct in sprom.c.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41944
Rework fallback sprom support by providing different sproms for
different chips. Also make it optional to use.
This likely causes sprom fallback support to break on a few boards.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41942
Now that BB is branched off, we can now switch to 3.14 and start
breaking stuff again.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41941
Add a working lzma loader and use it for generating initramfs kernels
to allow easily netbooting elf kernels on devices with a 4 MiB CFE
size limit.
Based on ar71xx's lzma-loader.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41940
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41939
This patch adds support for setting SPI_CS1 as Chip Select, Watchdog reset output and GPIO#27.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41938
this caused factory resets when reboot was pressed
Signed-off-by: Brent Thomson <brentthomson@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41932
without this the build for NBG6716 fails due to missing packages
https://dev.openwrt.org/ticket/17325
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41930
This is a backport of bcma from wireless-tesing/master tag master-2014-07-29-1.
For kernel < 3.10 this only adds the header changes needed by more
recent b43 versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41899
Fix a typo: gpio 21 is already used for the WPS led. Gpio 20 is the
right one (tested) for the mode switch. Confirmed that
/sys/kernel/debug/gpio state followed the position of the switch.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41858
Since kernel commit 928bea964827 ("PCI: Delay enabling bridges until
they're needed"), pci fixups are run with bridges (e.g. the pcie port)
disabled.
This causses hangs when ath9k_pci_fixup tries to manually enable the
device to apply the register fixups.
Fix this by enabling any parent bridges before trying to access the
device itself.
Fixes boot on DSL-274XB rev F1.
Reported-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41856
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 41841
Compile tested all subtargets and profiles.
Unfortunately I don't own any board affected by these changes, so no run tests.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41839
The earlier r41797 change was missing this part, to enable the right
vlan configuration.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41838
Since the earlier r41797 change, the board_name for awm003 has been
miscalculated, and sysupgrade has been broken. This seems to fix it.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41837
It doesn't seem to be used anywhere, it's incompatible with other
targets and can be confusing. People may think they need to update
section name every time they change VLAN ID (well, even I was doing
that).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41835
This is a backport of bcma and ssb from wireless-tesing/master tag
master-2014-07-22.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41804
The airGateway has a reset button connected to GPIO 12, so we should use it.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41794
ASL-26555 16MB: caldata is present on uboot-env and devdata, but the proper one seems to be the devdata, since mac address corresponds to Amper, the real manufacturer, meanwhile the caldata on uboot-env corresponds to D-Link.
ASL-26555 8MB: caldata is only present on uboot-env, but its mac address corresponds to Alpha, the real manufacturer.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41768
The default case in 02_network is inappropriate for the MikroTik RouterBOARD 91x boards because they do not have a WAN port, so don't bother setting the non-existent eth1 interface as the WAN port.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41767
This patch adds support for the Ubiquiti Networks airGateway.
Based in part on code posted by David Hutchison <dhutchison@bluemesh.net> on openwrt-devel:
https://lists.openwrt.org/pipermail/openwrt-devel/2013-December/023035.html
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
SVN-Revision: 41766
Update the kernel of the orion target to version 3.10.44.
Refresh orion config and patches to match the changes in the kernel
Tested on WRT350N-v2 device.
Signed-off-by: Maarten Bezemer <maarten.bezemer@gmail.com>
[run make kernel_oldconfig, fold a01-dt2-fixes-for-3.3.patch into dt2-setup.c,
make dt2-setup.c compile, fix harddisk subprofile]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41765
This fixes error erasing partial mtd partition which does not start on
eraseblock boundary and allows using fconfig to configure redboot on
devices such as the Gateworks Cambria.
Signed-off-by: Maciej Skrzypek <maciej.skrzypek@flytronic.pl>
SVN-Revision: 41733
Declare inline placeholder when usb_hcd_amd_remote_wakeup_quirk() not
compiled due CONFIG_PCI_DISABLE_COMMON_QUIRKS.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41702
Use AR2315_ prefix for macroses specific to AR2315/AR2316/AR2317 chips,
use AR5312_ prefix for macroses specific to AR5312/AR2312/AR2313 chips,
and use AR231X_ prefix for common macroses.
This patch should not cause any functional changes, only make clear
which macros is common and which macros is specific.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41701
Pass only physical address to 8250 serial port driver and set flag to
remap I/O memory inside the driver. Also fix AR5312 UART base address
definition, which seems specified already mapped.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41700
Pass PHY I/O memory region via platform resources and remap them
unconditionally.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41698
Each SoCs generation has own independent gpiolib realization, so we
have no reason to keep these realizations in semiuniversal form.
Following modifications are made:
* Remove valid_mask field
* Remove ar231x_gpio_chip structure
* Rename AR2315_GPIO_CR to AR2315_GPIO_DIR
* Fix count of AR5312 GPIOs
* Simplify gpio_chip methods realization
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41696
Currently AR5312 misc IRQ numbers are used for AR2315+ chips, what cause
us to use switch-case to map IRQ number to ISR bit. Introduce AR2315
specific misc IRQs set and simplify interrupt (un)mask operation.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41694
Rename interrupt control handlers to be consistent with operation names
and add IRQ chips names.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41693
UART IRQ number could be different for different SoCs, so make them
configurable.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41691
* Pass iomem and IRQ via platform device resources
* Remap iomem and use iowrite32 accessor function
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41688
Rename config symbol to AR2315_WDT to avoid confusion with other Atheros
SoCs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 41685
Move eeprom extraction from scripts to dts files.
Additionally there are few other changes like:
- whitespace fixes
- add partition labels where needed
- BR6524N board doesn't exist (lost in translation?)
- fix Edimax 3g-6200nl model
- add wmac eeprom to dts for Asus RT-N14U board
Compile tested all subtargets and their profiles.
Run tested on:
- Asus RT-N15
- Asus RT-N14U
- Buffalo WHR-600D
- Argus ATP52B
- Sparklan WCR-150GN
Few problems noted:
- many boards didn't have wmac eeprom information defined at all
- several boards don't have any patitions defined (see FIXME comments in dts)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41680
Some devices were renamed when converted from diag to in kernel board detection and it was not changed in netconfig. Devices not in the
kernel board detection are removed now.
This should close: #17111, #16968, #13202
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41663
The default case of ramips_setup_macs() is useful when mtd-mac-address is defined in dts.
But lan_mac is not set by default, this results in lan and wan having the same mac.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41632
Signed-off-by: Jon Suphammer <jon@suphammer.net>
Patchwork: http://patchwork.openwrt.org/patch/5838/
[juhosg:
- fix coding style,
- check the first and the last character of the MAC string
instead of using the strchr() function]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41622
The GL-Connect GL.iNet v1 router is basically a TP-Link TL-WR703N with
more DRAM/Flash, 2x Ethernet ports and console/GPIO header in the same
small form-factor:
<http://www.gl-inet.com/w/?lang=en>
Moreover, the manufacturer is promoting the OpenWrt usage to replace
the original firmware and proposing patches against both AA and trunk:
<http://www.gl-inet.com/w/?p=398&lang=en>
This is a clean up of the original manufacturer GPLv2 patch by alzhao,
proposed to the list by Mark Janssen.
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Mark Janssen <mark@sig-io.nl>
Signed-off-by: alzhao <alzhao@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5273/
[juhosg:
- remove user-space and image generation support, will be included
from other patches,
- fix coding style and drop superfluous comment in mach-gl-inet.c,
- rename and refresh kernel patch,
- adjust subject]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41618
The RB2011UiAS is almost exactly the same as the RB2011UAS, which is
already supported. Hardware-wise, it adds a passive power injector on
Eth10. Software-wise, Routerboot passes a different board name on the
kernel command line. Hence the need for a patch.
Not yet working:
* touchscreen: doesn't work on RB2011UAS either. The touchscreen itself
seems to be driven by an ADS7843-compatible IC, but figuring out which
GPIO pins it's connected to is work for the future.
* control of power injector: remains off. Probably also GPIO-controlled.
Signed-off-by: Soren Harward <stharward@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/5841/
[juhosg: rename and refresh the kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 41617
- adsl and lan leds are swapped.
- internetkey is labeled as hspa.
- enable status led and reset button for failsafe.
- use new leds script.
- fix switch configuration.
- remove enet0 from board_info.
- add profile.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41588
This patch also makes use of the new leds script.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41585
By using uci-defaults force_link is enabled, which fixes some link issues if ethernet cable isn't connected when LAN is initialized.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41583
Run lantiq_board_detect from lantiq_board_name and lantiq_board_model.
This was the one thing missing from r41474 for sysupgrade board
detection to work properly.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41567
Disables gluebi and enables ubiblock on lantiq xway. Squashfs
images on nand use ubifs instead of jffs2 for the overlay.
I'll leave the equivalent patch for xrx200 to someone who has a
board to test.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41565
With help of this script the ath10k board.bin settings are loaded from
flash and saved to the ath10k firmware directory. The driver reads it
later in the boot process.
Signed-off-by: André Valentin <avalentin@marcant.net>
SVN-Revision: 41562
