Define USB port power on/off GPO as voltage regulator type instead of
exposing as a normal GPIO.
The GPO is now controlled by the USB driver via the voltage regulator
definition. The regulator is of fixed output type (5V for USB) hence the
GPO switches power on/off to USB pin 1 (Vcc)
USB port power is enabled on driver load and disabled on driver unload.
Enable kernel support for fixed voltage regulator types on mt7621.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Some board vendors actually changed the loader to expect the chip
to come up in 4-address-mode and flipped the ADP bit in the flash
chip's configuration register which makes it come up in 4-address-mode.
Hence it doesn't make sense to avoid switching to 4-address-mode on
those boards but the opposite as otherwise reboot hangs eg. on the
WrtNode2 boards. Fix this by checking the ADP register and only using
SPI_NOR_4B_READ_OP on chips which have ADP==0 (come up in 3-byte mode).
See also datasheet section 7.1.11 Power Up Address Mode (ADP)
Fixes: 22d982ea0 ("ramips: add support for switching between 3-byte and 4-byte addressing on w25q256 flash")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a port of an old commit from mkresin's tree:
09260cdf3e9332978c2a474a58e93a6f2b55f4a8
This has the potential to break sysupgrade but it should be fine as
there is no stable release of LEDE or OpenWrt that support these devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
I was carrying a local commit that added the sdhci stuff and missed it
as a result.
Also fix the rgmii3 thing in the PC2 DTS file as that's bogus and causes
a dmesg warning that it's bogus.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
That commit exposed a bug in the DTS files used by mt7621 where the wrong
reg value for pcie1 (and potentially pcie2) was being used. This was
causing WiFi failures for interfaces in pcie1.
eg. 2.4GHz working but not 5GHz.
As all of these dts entries are already specified in mt7621.dtsi, remove
them.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
There's nothing connected to i2c on this board, so remove it.
Also edited the gpio group to match the PC2 as they're the same.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
There was an error on initial commit, the proper soc is mt7620n (which is
more limited than mt7620a). Moreover, there is a battery management
controller connected to the i2c port of the mt7620n. I have a small piece
of i2c code to get battery level coming.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
This commit alters the TP-Link Archer C50v3 LED settings to use the phy
trigger instead of the netdev one. This way the WiFi status is displayed
even if the wifi interface name is altered.
Signed-off-by: David Bauer <mail@david-bauer.net>
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
BOCCO is a communication robot provided by YUKAI Engineering Inc.
SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Mostly whitespace cleanups. Some unneeded code was removed.
MMC init was also moved to the probe function as in
6069bdd
The cleanup commits are over 100, making it hard to do them individually.
Tested on GnuBee PC1 with an SD card being used as swap.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
v2: Fixed compile issue with mt7620
Backport patch adding support for the vbus-supply devicetree property,
which allows to specific GPIOs (via fixed regulators) to enable
vbus/usb power.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: f079b6406348 ("staging: mt7621-eth: add gigabit switch driver (GSW)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function of_phy_connect() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is an amagalmation of two upstream commits dealing with whitespace
and dead code removal. I'm synching instead of having two separate commits
as they go out of order compared to previous commits here.
Tested on GnuBee PC1.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Mostly whitespace cleanups. Some unneeded code was removed.
MMC init was also moved to the probe function as in
6069bdd087
The cleanup commits are over 100, making it hard to do them individually.
Tested on GnuBee PC1 with an SD card being used as swap.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These resources are extracted from devicetree, so they aren't
needed here.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code currently defines:
and then compiles code only if they are defined.
We might want to disable some of these via devicetree one
day, but for now just remove the #defines and the
conditions - all the code for different ports is
easy to identify.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.
The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the owner assignment form the platform driver as
platform_driver_register() already initializes the owner.
Found using coccinelle.
Signed-off-by: Christian Lütke-Stetzkamp <christian@lkamp.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Splitted out the dts file and create the new dts for the 256 MByte RAM and
the 512 MB RAM version.
Migrate both versions to the common board detection.
The install the 512 MByte Version on a board running the 256 MByte image,
a forceful sysupgrade with the -F flag is required.
Signed-off-by: Davide Ammirata <list@davidea.it>
The RavPower WD03 is a battery powered SD card reader and a USB port.
Specifications:
SOC: MediaTek MT7620N
BATTERY: 6000mah
WLAN: 802.11bgn
LAN: 1x 10/100 Mbps Ethernet
USB: 1x USB 2.0 (Type-A)
RAM: PM Tech PMD708416CTR-5CN 32 MB
FLASH: Holtek HT66F40 - 8 MB Flash
LED: Power button and 4 leds to indicate power level of the
battery (could not get control of that)
INPUT: Power, reset button
OTHER: USB SD-Card reader with card detect on GPIO#42
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Installation:
- Download the sysupgrade image
- Place it in the root of a clean TFTP server running on your computer.
- Rename the image to "kernel" — be sure there is no file extension.
- Plug the WD03 into your computer via ethernet.
- Set your computer to use 10.10.10.254 as its IP address.
- With your WD03 shut down, hold down the power button until the first
white LED lights up.
- Push and hold the reset button and release the power button. Continue
holding the reset button for 30 seconds or until it begins searching
for files on your TFTP server, whichever comes first.
- The WD03 (10.10.10.128) will look for your computer at 10.10.10.254
and install the kernel file. Once it has finished installation of the
kernel file, it will search for a (nonexistent) rootfs file — when it
begins searching for this file, shut down the WD03 by holding the
power button normally.
- Start up your WD03 normally.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
There is no pinmux group "jtag" for mt7628 and the pinmux driver fails
to load due to the use of the not existing group.
Fixes: FS#1515
Signed-off-by: Mathias Kresin <dev@kresin.me>
The old DTB method (OWRTDTB) is not recognized by the boot process
anymore with 4.9/4.14.
This patch reuses KERNEL_DTB to get a valid DTB applied to the kernel
image.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
