Commit graph

14993 commits

Author SHA1 Message Date
Rafał Miłecki
7caa9411e7 brcm47xx: add kernel 4.4 support
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47930
2015-12-18 07:25:13 +00:00
John Crispin
4afe0fc2b2 ralink: update the mt7621 ethernet support patch
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47929
2015-12-17 12:14:56 +00:00
John Crispin
1f71f2220d ar71xx: add support for TRENDnet TEW-823DRU
Add support for TRENDnet TEW-823DRU:
- cpu: QCA9558 @720MHz
- flash: 16MB
- ram: 256MB
- 4+1 RJ45 100/1000Mbps
- wifi:  QCA9558 (bgn) and QCA9880-BR4A (ac)
- 1x USB 2.0

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 47927
2015-12-17 09:30:05 +00:00
John Crispin
68ff0d3d78 omap: add kernel 4.4
- tested on Beagleboard C4

Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>

SVN-Revision: 47925
2015-12-17 09:29:48 +00:00
John Crispin
d4b8d51580 brcm2708: update 4.1 patches
As usual, this patches were taken (and rebased) from
https://github.com/raspberrypi/linux/commits/rpi-4.1.y

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47922
2015-12-17 09:29:22 +00:00
John Crispin
f0b708acdf cns3xxx: add GW2393 Support
Based off of the GW2391-C, but with the following changes:
 * 4x4in to 4x5in pcb
 * flat panel connector for LED signals

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>

SVN-Revision: 47920
2015-12-17 09:28:42 +00:00
John Crispin
c6d95f0752 cns3xxx: Fix comment
Original comment was wrong about which pads are being set.

Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>

SVN-Revision: 47919
2015-12-17 09:28:35 +00:00
John Crispin
21493c984a lantiq: fix ARV7519RW22 buttons
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47918
2015-12-17 09:28:29 +00:00
John Crispin
0a6a37be83 lantiq: add the TDW8980 5GHz led
Still unused, but u-boot doesn't take care of the led, which results in a
permanent switched on 5GHz LED.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47915
2015-12-17 09:28:01 +00:00
John Crispin
ab77d4bcb9 lantiq: Fix LED handling.
- Use common OpenWrt blink patterns instead of custom ones
- Add preinit_regular hook
- Handle the TDW89X0 that does not have a configurable power LED

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47914
2015-12-17 09:27:52 +00:00
John Crispin
34934609f9 lantiq: Configure LED polarity for TDW8970.
This patch configures the correct ath9k WLAN LED polarity for the TDW8970.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47913
2015-12-17 09:27:46 +00:00
John Crispin
ec21c9821c lantiq: Configure disabled WLAN bands for TDW89X0.
The TDW8970 has a AR9381, which is the bgn 3x3:3 variant of the AR938x family.

The TDW8980 has a AR9287, which is the bgn 2x2:2 variant of the AR928x family.

This means that the chip for both routers is 2.4 GHz only.

Anyway, the manufacturer didn't disable the 5 GHz band in the EEPROM partition
(at least on my TDW8970).

So this patch disables the 5 GHz band.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47912
2015-12-17 09:27:40 +00:00
John Crispin
f2fd516d72 lantiq: Allow configuration of ath9k disabled bands and LED polarity from the device tree.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47911
2015-12-17 09:27:31 +00:00
John Crispin
932bc8d5eb ath9k: Allow configuration of LED polarity in platform data.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 47910
2015-12-17 09:27:24 +00:00
John Crispin
7de7bd0201 ramips: mt7621: fix error message when initramfs is too large
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47908
2015-12-17 09:27:09 +00:00
John Crispin
1c5136c4c3 ramips: remove unwanted change from patch
Remove unwanted change to irq-mips-gic.c from mt7621 support patch

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47907
2015-12-17 09:27:00 +00:00
John Crispin
43422a634b ramips: change CM_GCR_BASE_CMDEFTGT_MEM value to match datasheet
Zero config value for default memory region means 'memory', not
not 'disabled' according to 'Control Registers Of The Coherency
Manager' manual.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47906
2015-12-17 09:26:51 +00:00
John Crispin
acbed0eff3 ramips: mt7621: undo mips-cm probe hack to not wipe out memory regions
Since now we hopefully setup memory regions properly we no longer need this hack.

Tested and works on ubnt-erx.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47905
2015-12-17 09:26:43 +00:00
John Crispin
622e268710 ramips: mt7621: setup memory region for pcie controller memory
Only compile tested since I do not have any hardware with
devices on pcie bus.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47904
2015-12-17 09:26:35 +00:00
John Crispin
e8890c6be0 ramips: mt7621: add patch to setup CM memory region for palmbus
This is tested and works on ubnt-erx.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47903
2015-12-17 09:26:28 +00:00
John Crispin
b4bb10b3a0 ralink: update config files to build the cleaned up ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47902
2015-12-17 09:26:20 +00:00
John Crispin
402db12f1a ralink: drop dummy profile from mt7688
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47901
2015-12-17 09:26:09 +00:00
John Crispin
651e620de5 ralink: fixup devicetree files to work with new ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47900
2015-12-17 09:25:57 +00:00
John Crispin
fa854a02a1 ralink: drop old ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47899
2015-12-17 09:25:30 +00:00
John Crispin
31116661ff ralink: add reworked ethernet driver
update to the version of the driver that is on its way upstream

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47898
2015-12-17 09:25:24 +00:00
Rafał Miłecki
716905b986 bcm53xx: print bcm47xxpart buf to debug R8000 UBI problem
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 47896
2015-12-16 09:37:16 +00:00
Imre Kaloz
5705d058eb generic/4.4: bump to -rc5
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 47894
2015-12-15 11:20:38 +00:00
Felix Fietkau
6505dc3367 ar71xx: clean up ethernet tx queue after reset, wake queues when done - fixes hangs reported in #18922
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47892
2015-12-14 20:22:09 +00:00
Felix Fietkau
6b87e0706d ar71xx: Update merakinand.sh to fix sysupgrade
Remove reliance on /lib/upgrade/nand.sh as this is called by sysupgrade,
based on felix's comments at
https://lists.openwrt.org/pipermail/openwrt-devel/2015-December/037963.html

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47889
2015-12-13 18:05:42 +00:00
John Crispin
5d4f5689fd ramips: add missing kernel symbols
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47884
2015-12-12 21:01:02 +00:00
Felix Fietkau
bb52e2e1ef ar71xx: add rx/tx delay definitons for qca955x's MAC
This patch adds the rx/tx register offsets for the qca955x SoC.

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47882
2015-12-12 11:27:51 +00:00
John Crispin
4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
John Crispin
1c6c9549d6 ramips: add support for Spansion S34ML0[24]G2 flash
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47880
2015-12-12 07:37:53 +00:00
John Crispin
abc84551c0 ar71xx: add support for Cisco's MR18
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47878
2015-12-12 06:42:29 +00:00
John Crispin
9e5044926b ralink: remove stray "+" from ethernet driver
this is what you get if you manually apply patches with c&p

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47877
2015-12-12 06:42:17 +00:00
John Crispin
8470e30a76 ramips: move partition definitions out of mt7621.dtsi file
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47876
2015-12-12 06:42:11 +00:00
John Crispin
e610cdfc8a ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47875
2015-12-12 06:42:05 +00:00
Felix Fietkau
0b6271faf4 ar71xx: reorganize target patches/files to make it possible to add boards without adding patch files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47874
2015-12-11 21:12:14 +00:00
Felix Fietkau
0186d4c2c2 ar71xx: on wnr2200, revert the mac0/mac1, the ethernet interfaces are swapped. use MAC1 for wlan
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47873
2015-12-11 21:12:04 +00:00
Felix Fietkau
77bedbe80d Revert "ramips: use gic timer as clocksource for mt7621"
This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7.

SVN-Revision: 47872
2015-12-11 19:22:15 +00:00
Felix Fietkau
6e12ef7430 ar71xx: fix MAC address swapping on WNR2200 and fix the WLAN MAC address
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47871
2015-12-11 19:21:59 +00:00
Jo-Philipp Wich
67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
Jo-Philipp Wich
b0b8293b7e brcm47xx: migrate network config to board detection framework
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47866
2015-12-11 15:19:43 +00:00
John Crispin
0938233fcd lantiq: get rid of ltq-vdsl-fw
Because of dsl-vrx200-firmware-xdsl-* there's no need anymore to
download a dsl firmware at runtime.

Signed-off-by: Andre Heider <a.heider@gmail.com>

SVN-Revision: 47851
2015-12-11 15:05:40 +00:00
John Crispin
787120e3a3 lantiq: fix led setup after switch to uci-defaults-new.sh
The switch to uci-defaults-new.sh revealed a bug in the former used
uci-defaults.sh, which failed to add leds with colons in the led name.

This bug isn't any longer present in uci-defaults-new.sh and therefore
all via DT defined leds will be added to /etc/config/system with their initial
on/off state, regardless whether they are already added by the board specific
led mappings.

This results for a BTHOMEHUBV5A into the following led configuration:

- soc:blue:power is added as led_power with the initial state "switched on"
- soc:blue:power is added as led_soc_blue_power with the initial state "switched off"

With the final result of a switched off power led after boot.

The only led that needs to be added is the BTHOMEHUBV5A specific dimmed led.

Signed-off-by: Mathias Kresin <openwrt@kresin.me>

SVN-Revision: 47850
2015-12-11 15:05:30 +00:00
John Crispin
1d2a4ec287 ar71xx: build image for TL-WR710N v2.1
This patch just extends target/linux/ar71xx/image/Makefile to build
images also for version 2.1 of TL-WR710N
patch against the latest git

Signed off by: Norbert Wegener <nw@wegener-net.de>

SVN-Revision: 47849
2015-12-11 15:05:20 +00:00
John Crispin
1dada3fc3c ar71xx: add LED driver NU801
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47848
2015-12-11 15:04:57 +00:00
John Crispin
eb8ff56684 ar71xx: Add support for Wallys DR344
This patch is for Wallys DR344 support under OpenWRT

Signed-off-by: Philippe Duchein <wireless-dev@duchein.net>

SVN-Revision: 47847
2015-12-11 15:04:47 +00:00
John Crispin
fcf74b1138 ar71xx: image for AP121/16M
Build image for the AP121 reference board with 16MB flash.

Signed-off-by: Norbert Wegener <nw@wegener-net.de>

SVN-Revision: 47846
2015-12-11 15:04:22 +00:00
John Crispin
9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00