Commit graph

16837 commits

Author SHA1 Message Date
Rafał Miłecki
28955d9707 kernel: use upstreamed patch for BCM53573 support in bcm47xxsflash
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-11-08 11:36:39 +01:00
Christian Lamparter
b5638bb64e apm821xx: redo WAN green and yellow LEDs
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-11-08 11:17:10 +01:00
Pavel Kubelun
524d7a7cde ipq806x: fix pcie reset gpios
Fix perst-gpios property in accordance to the driver, so it stops spamming that it can't parse it.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-08 11:17:10 +01:00
Henryk Heisig
4ad68fa0a2 ar71xx: tl-wpa8630: Fix kernel lenght
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Roger Pueyo Centelles
5f6e948551 ramips: Add support for Wavlink WL-WN575A3
This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug
wireless router with the following specifications:

 - CPU: MediaTek MT7628AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 2x 10/100 Mbps (switched)
 - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm
 - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm
 - Antennas: 4x external (2 per radio), non-detachable
 - LEDs: 4 programmable + LAN, WAN, POWER
 - Buttons: reset, WPS

Flashing instructions:

Factory U-boot launches a TFTP client if WPS button is pressed during power-on.
Rename the sysupgrade file and configure a TFTP as follows:

 - Client (WL-WN575A3) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-11-08 11:17:10 +01:00
BangLang Huang
bc4109845d ramips: fix Newifi D1 profile
the images were generated for the wrong flash size.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-11-08 11:17:10 +01:00
Rafał Miłecki
e2a65f4aa5 bgmac: backport small DMA fix
It's supposed to significantly improve performance but doesn't seem to
affect Northstar unfortunately. It seems only some other platforms were
limited because of this DMA setup mistake.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-11-07 14:42:58 +01:00
Rafał Miłecki
4fae9db765 kernel: fix bgmac regression causing BCM47186B0 SoC hangs
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-11-07 14:30:32 +01:00
Jo-Philipp Wich
95ac6906aa arm64: switch boot-wrapper to working repository
The original repo in this Makefile disappeared from the internet so use another
copy of this repository on kernel.org. Also switch from git:// to https://
while being at it.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-11-05 16:10:05 +01:00
Koen Vandeputte
347884b345 cns3xxx: fix UART resource overlap
Port 1 registers the same IO resources as port 2 in the kernel resource
tree, which is wrong.
Fix this by using it's own resources as indicated in the overview
(cns3xxx.h).

Compiled & Tested on several GW2388-4 laguna boards which utilizes all 3
ports.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-11-05 10:18:27 +01:00
Felix Fietkau
3616666126 ipq806x: fix zyxel image build error
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
Felix Fietkau
fcf90318c5 ipq806x: clean up the kernel config and reduce kernel image size by disabling some unnecessary code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
Felix Fietkau
fddd532612 ipq806x: fix a kconfig issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
Christian Lamparter
8f2c2f94cf apm821xx: add back end-of-UBI marker for the WNDR4700 and MR24
The patch "build: drop UBI EOF marker from images by default"
(commit d27bce8d28) removed the
end-of-UBI marker. Without this marker, the boards will panic
during boot:

[    1.683458] ubi0: attaching mtd4
[    1.696181] ubi0 warning: scan_peb: valid VID header but corrupted EC header at PEB 31
[    1.704367] ubi0 error: scan_peb: bad image sequence number 549886691 in PEB 32, expected 184585623
[    1.713377] Erase counter header dump:
[    1.717110]  magic          0x55424923
[    1.720843]  version        1
[    1.723797]  ec             0
[    1.726752]  vid_hdr_offset 512
[    1.729880]  data_offset    2048
[    1.733094]  image_seq      549886691
[    1.736740]  hdr_crc        0x92ba8130
[    1.740472] erase counter header hexdump:
[    1.744493] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd4, error -22
[    1.751528] UBI error: cannot attach mtd4
[    1.755373] hctosys: unable to open rtc device (rtc0)
[    1.761130] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.768604] Please append a correct "root=" boot option; here are the available partitions:
[...]
[    1.856992] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    1.866519] Rebooting in 1 seconds..Auto calibration ---

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-11-04 11:11:34 +01:00
Mathias Kresin
3db1a5c8fa lantiq: use external pci clock on ARV7506PW11
Fixes a ralink wireless driver related kernel crash as soon as a lot of
data is tranfered via wireless.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-03 19:00:28 +01:00
Mathias Kresin
112cf52d45 lantiq: cleanup dts files
- remove not existing properties
- remove properties having the same values as the included dtsi
- remove nodes which are disabled in the included dtsi and not enabled
  in dts
- replace the deprecated pinctrl-* compatible strings
- use the same labels for nodes as the included dtsi
- move common used vr9 pci properties to vr9.dtsi
- remove the unused stp node from HomeHub 2B devcie tree source file
- fix spaces vs. tabs and remove superfluous linebreaks

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-03 19:00:28 +01:00
Pavel Kubelun
b2135f3ba5 ipq806x: update DT in accordance to new drivers And add some more DT nodes
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
681f28990d ipq806x: switch to generic cpufreq driver cpufreq-dt
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver

Also switching to ondemand frequency scaling as it is fixed now

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
a154a3d8be ipq806x: add opp patches for voltage scaling
Preparing for cpufreq driver switch to generic cpufreq-dt

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
8749fb7894 ipq806x: update clk-qcom patches
Preparing for cpufreq driver switch to generic cpufreq-dt

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
bf7166e545 ipq806x: fix leds, sata port for Netgear R7800 and minor fixes - renamed leds in correct color accordance - blink power led with white during boot and with amber when flashing firmware - fixed usb leds - enabled unused wps and rfkill leds as wlan leds. Now rfkill led is for 2.4GHz and wps - 5GHz WIFI - removed unneeded bootargs - removed unneeded pci pins from R7800 DT (driver already handles it in proper way) and add tx offsetting - nand ecc step size - fixed sata ports
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Sven Schwermer
5511c1c7c1 ramips: Use MT7621 I2C driver for MT7628/MT7688
The i2c-ramips driver does not work for the MT7628/MT7688 SoCs, the
i2c-mt7621 driver does.

Signed-off-by: Sven Schwermer <sven.schwermer@arcor.de>
2016-11-03 08:27:20 +01:00
Cezary Jackiewicz
dafbc94f95 ipq806x: TP-Link Archer C2600: convert old usbdev trigger to new usbport
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-11-03 08:21:32 +01:00
Andrew Yong
faf94d926e ramips: add support for MikroTik hEX v3 (RB750Gr3)
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).

RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.

Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.

The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.

A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-02 10:25:44 +01:00
Stijn Segers
2f2ea7b44c kernel: update kernel 4.4 to version 4.4.30
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.

Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Stijn Segers
eefe07ef4d ramips: add usb packages into DIR-860L B1 profile
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-11-02 10:25:44 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Yutang Jiang
15a14cf166 layerscape: add 64b/32b target for ls1012ardb device
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.

The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
2016-10-31 17:00:10 +01:00
Yutang Jiang
c6c731fe31 layerscape: add 64b/32b target for ls1043ardb device
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.

LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.

64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.

All of 4.4 kernel patches porting from SDK release or upstream.

QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
2016-10-31 17:00:10 +01:00
Henryk Heisig
a34f96d6cf ramips: Archer C50 cleanup
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>

Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-31 16:58:41 +01:00
Stefan Koch
7929ab60bf lantiq: add vpe/watchdog modules to kernel
(required not-distributable firmware blob - dump it by yourself from original firmware)

Signed-off-by: Eddi De Pieri <eddi@depieri.net>

(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:33 +01:00
Stefan Koch
4552bf158c lantiq: vpe softdog
(required not-distributable firmware blob - dump it by yourself from original firmware)

Signed-off-by: Eddi De Pieri <eddi@depieri.net>

(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)

Modified after cherry-pick:
obj in Makefile

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:33 +01:00
Stefan Koch
e0229a16b0 lantiq: added support for VPE1
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756

If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1

To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:33 +01:00
Stefan Koch
01ab5209c0 lantiq: modify vr9.dts to support vmmc
(required not-distributable firmware blob - dump it by yourself from original firmware)

Signed-off-by: Eddi De Pieri <eddi@depieri.net>

(cherry picked from commit 8d924d43c0ea6839a3a33e54982e8da48b736001)

Modified after cherry-pick:
compatible attribute

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-31 16:51:32 +01:00
Pavel Kubelun
8f7e58c0fe ipq806x: add reserved memory node in Netgear R7800
KERNEL BUG: BAD_PAGE_STATE in process appears here and there during intensive memory usage.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-10-31 16:48:04 +01:00
Rosen Penev
369884c2a1 ramips: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2016-10-31 16:41:26 +01:00
Henryk Heisig
0744b6a044 ipq806x: ArcherC2600: export usb power pins
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 16:40:54 +01:00
Henryk Heisig
dbf2feb2b3 ipq806x: ArcherC2600: devictree cleanup
add blank lines and use macros for GPIOs

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 16:40:28 +01:00
Paul Wassi
a569354481 kernel: update kernel 4.4 to version 4.4.28
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on ar71xx, brcm47xx, kirkwood.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-10-31 16:33:53 +01:00
Hauke Mehrtens
76847c7fc9 kernel: deactivate CONFIG_QCOM_SPMI_TEMP_ALARM
This fixes the build of the ipq806x target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-10-31 14:35:30 +01:00
Chris Blake
53b43e65e7 ar71xx: Add net config for MR12 & MR16
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-31 12:52:56 +01:00
Christian Mehlis
7cb82d4b70 ar71xx: fix ethernet on wpj344 board
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
2016-10-31 12:52:56 +01:00
Rafał Miłecki
f20ba0f0d5 brcm47xx: image: use append-rootfs step for per-device rootfs support
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-28 17:03:55 +02:00
Rafał Miłecki
027b2c5b83 brcm47xx: image: make TRX steps work with rootfs passed as $@
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-28 16:46:57 +02:00
Rafał Miłecki
8bd2167236 brcm47xx: image: make linksys-pattern-partition leave specific file
Thanks to leaving .pattern file we can easily insert extra step between
linksys-pattern-partition and trx-v2-with-loader, e.g. rootfs one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-28 16:41:05 +02:00
Rafał Miłecki
c9fdb23345 apm821xx: fix USB LED trigger for WNDR4700
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-28 13:27:21 +02:00
Rafał Miłecki
bc6be3e953 brcm47xx: add support for per-device rootfs
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-27 13:25:51 +02:00
Koen Vandeputte
d9c3727288 imx6: Add ds1672 RTC to kernel for working hctosys (Gateworks)
Fixes the same hctosys init issue as described in commit
5481ce9a11

The Gateworks Ventana family uses an emulated Dallas 1672
RTC device.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-10-27 00:34:01 +02:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
6b0d279ca5 ar71xx: build relocate stub for generic and legacy images
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
e19427bd79 ar71xx/base-files: rename 09_fix-trx-header 09_fix-checksum
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Stijn Tintel
136319e72d kernel: mtdsplit: add support for WRGG images
Support splitting WRGG images, found in some D-Link devices (e.g.
DAP-2695).

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Chuanhong Guo
c5a7e2c2fb ar71xx: Ignore firmware building errors of UBNT and CyberTAN devices
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2016-10-26 14:07:20 +02:00
André Valentin
1465bebd74 ipq806x/nbg6817: add sysupgrade support
Add new way of flashing to mmc devices based on rootfs split with loop devices.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:47 +02:00
André Valentin
d8059e3a30 linux/mtd: add id for mx25u3235f needed by ZyXEL NBG6817
Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:47 +02:00
André Valentin
a0ed7af6c6 ipq806x/nbg6817: add support for ZyXEL NBG6817
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:46 +02:00
Stefan Koch
b760afa09a lantiq: danube fxs bugfix: changed compatible attribute of vmmc
This bugfix enables FXS support on dabube based devices.
Changed "compatible" attribute from "vmmc" to "vmmc-xway".
The vmmc driver uses "vmmc-xway".

Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
2016-10-26 12:37:46 +02:00
Paul Wassi
d2606107ab kirkwood: fix pogo_e02 LED name
The pogo_e02's dts file has its LEDs named "pogo_e02:(...)"
Fix the status-LED's name for this device.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 12:37:46 +02:00
Xuefu Lin
8312738806 ramips: fix PSG1218 LEDs
Signed-off-by: Xuefu Lin  <xuefulin@gmail.com>
2016-10-26 12:37:45 +02:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00
Paul Wassi
f6b5df44d9 kirkwood: remove redundant code in etc/board.d/02_network
Remove redundant code: merge boards/cases that share
the same network configuration.
Also fix the alphabetical ordering of the cases.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 12:37:45 +02:00
Chris Blake
fac018b25e ar71xx: Remove switch config for the MR12/MR16
These boards do not have a switch, so they should have never been added
to this file in the first place.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:45 +02:00
Chris Blake
28dd52b079 ar71xx: add mac partition to the MR12/MR16
On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space
after u-boot-env is used to store the boards Mac address. Sadly as this
was removed on any device already on OpenWRT/LEDE, moving forward a new,
64k partition named "mac" will be used to store the mac address for the
device (which is the minimum size). This allows users to properly set
the correct MAC, without editing the ART partition (which holds the same
MAC for all devices).

The reason the space is taken from kernel instead of rootfs is currently
kernels are only 1.3MB, so that way we can leave the current rootfs
space alone for users who fully utilize the available storage space.

Once this partition is added to a device, you can set your MAC doing the
following:

mtd erase mac
echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5
sync && reboot

Where 00:18:0a:33:44:55 is your MAC address.

This was tested, and confirmed working on both the MR12 and MR16.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:45 +02:00
Chris Blake
d8662ac3c6 ar71xx: Move MR12 & MR16 from legacy to generic
This moves the Meraki MR12 and Meraki MR16 to the new generic target.
Tested and verified working on both devices.

Note that kernel/rootfs images are still generated. This is because they
are used for the inital flashing process due to the fun pace at which
UBoot erases/writes to SPI.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:44 +02:00
Petr Štetiar
5481ce9a11 imx6: Add ds1307 RTC to kernel for working hctosys
Otherwise if we use ds1307 as kernel module, hctosys fails as ds1307 is
being initialized later then hctosys:

 [    2.427349] hctosys: unable to open rtc device (rtc0)
 [    3.714263] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
 [    8.990061] rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2016-10-26 09:41:29 +02:00
Paul Wassi
5528573039 kirkwood: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2016-10-26 09:41:28 +02:00
Jing Lin
7ba9a3a504 ar71xx: Add support to DomyWifi DW33D
Signed-off-by: Jing Lin <mumuqz@163.com>
2016-10-25 17:51:08 +02:00
Rafał Miłecki
93f9a9c71c kernel: backport MIPS's ioremap_cache from 4.5
It's needed by (updated) bcm47xxsflash driver.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 22:52:44 +02:00
Rafał Miłecki
13e6f7a75d brcm47xx: reorder older entries in image Makefile
Keep all entries sorted and replace tabs with spaces while at it.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 20:35:24 +02:00
Stijn Tintel
839b657a61 kernel: add fix for CVE-2016-5195
Add fix for CVE-2016-5195 to kernel 3.18 and 4.1.
Kernel 4.4 is already fixed since version 4.4.26 which was committed in
32c28a78f7.

Patches taken from Sasha Levin's linux-stable git tree:
http://git.kernel.org/cgit/linux/kernel/git/sashal/linux-stable.git/

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-24 20:25:14 +03:00
Stijn Tintel
75e63c2494 kernel: update kernel 3.18 to version 3.18.43
Refresh patches for all targets supporting 3.18 and not marked broken.
Compile-tested on all targets using 3.18 and not marked broken.

Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-24 20:25:14 +03:00
Stijn Tintel
2fc3680dd0 kernel: update kernel 4.1 to version 4.1.34
Refresh patches for all targets supporting 4.1 and not marked broken.
Compile-tested on all targets using 4.1 and not marked broken.

Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.
Changes to generic/666-Add-support-for-MAP-E-FMRs-mesh-mode.patch based
on a90ee92337.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-24 20:25:14 +03:00
Rafał Miłecki
06405df7a8 brcm47xx: bump kernel to 4.4
Kernel 4.4 was ready for brcm47xx for almost a year now but I kept
postponing the bump due to problems with Linksys WRT300N v1.0. OpenWrt
and LEDE with 4.4 were hanging at the booting with the:
> Starting program at 0x80001000
(the last CFE message).

This was a permanent state, "make distclean" wasn't helping, I spent
hours debugging this and I was reliably reproducing the issue every
time. I also reported it on linux-mips ML in the thread:
> BCM4704 stopped booting with 4.4 (due to vmlinux size?)

After ~month I started working on WRT300N again. I got hangs as expected
every time I switched from 4.1 to 4.4. I started experimenting with:
1) TRX content (I tried dropping rootfs partition)
2) BZ_TEXT_START of lzma-loader
3) Flashing other variants of image: lzma compressed kernel (without a
   loader), gzip compressed one, uncompressed one.

At some point I got rootfs-less image booting and after that I couldn't
reproduce problem anymore, even with a complete firmware. It seems like
hardware was in some locked/unstable state that got magically fixed.

I have LEDE working now, tested it even with "make distclean", it seems
we can bump kernel now. I'll keep testing it on WRT300N for some time.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 17:22:23 +02:00
Rafał Miłecki
6e64a38b00 brcm47xx: build also TRX image for Linksys WRT300N V1
Linksys WRT300N V1 has pretty bugged CFE bootloader (it crashes in a lot
of situations) that doesn't accept .bin image.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 10:34:59 +02:00
Rafał Miłecki
337f219130 brcm47xx: open code Makefile entries for all devices
If we want to use some of new features like per device rootfs we will
need this to specify them there.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 10:33:33 +02:00
Imre Kaloz
3764caa934 mvebu: add support for the Linksys WRT3200ACM (Rango)
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-10-24 08:45:06 +02:00
Imre Kaloz
2beab73fad mvebu: add missing status LEDs for Linksys WRT1200AC and WRT1900ACv2
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
2016-10-24 08:45:06 +02:00
Álvaro Fernández Rojas
920f922652 kernel: update kernel 4.4 to version 4.4.27
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-10-23 14:56:09 +02:00
Rafał Miłecki
3b26a5bb15 bcm53xx: include b43 in Tenda AC9 image
There is some (poor?) support for BCM43217 in b43.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-20 08:46:26 +02:00
Mathias Kresin
3c5a8a2cbc lantiq: enable cpu temp driver for all vr9 boards
Only present on v1.2 vr9 SoCs but the driver takes care to not load on
boards having a v1.1 SoC.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:06 +02:00
Mathias Kresin
23e3314cad lantiq: fix thermal sensors driver
Read the temperature including the decimale place from the CGU_GPHY1_CR
register.

Decrement the temperature read from the register by 38.0 degree celsius.
The temperature range of the sensor is -38.0 to +154 °C and the register
value 0 is equal to -38.0 °C. This fixes the report of unrealistic
temperatures as seen on all tested boards.

Give the SoC a few milliseconds to get the first temperature value. On
some rare occasions there is no temperature value in the register when
read the first time after activation. This leads to a reported
temperature of -38.0 °C on boot.

Only version 1.2 of the vr9 SoC has a temperature sensor. Add a check
to make sure the driver doesn't load on v1.1 vr9 SoCs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:06 +02:00
Andreas Eberlein
eba84bee4c lantiq: Sanitize device tree files
The device tree file of ARV752DPW uses numbers/hex values for gpio states and input event codes.

This cleans it up and uses the available macros from header files. This way the functions are easier to read and comprehend.

Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
[sanitize all device tree files]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:04 +02:00
Andreas Eberlein
72d12672de lantiq: Fix buttons for ARV752DPW
The GPIO for reset switch is wrong in definition. Further the key codes for the two additional buttons are ineffective.

Both is fixed here.

Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
2016-10-19 19:06:15 +02:00
Mathias Kresin
fa14124616 lantiq: use new build code for DGN3500
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Mathias Kresin
1f7a03a706 lantiq: drop lzma-loader
It isn't used any more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Mathias Kresin
17094e9e64 lantiq: rework VG3503J image
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.

To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:

  VR9 # run reset_uboot_config
  VR9 # reset
  VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The mac address is printed on the label at the bottom of the case.

The following steps are need to be done during first install:

  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.

Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.

A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Rafał Miłecki
ea7462ae07 bcm53xx: include usbport trigger for devices with USB
We don't have any code for enabling it automatically yet but it allows
adding entries manually to the /etc/config/system.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:28:52 +02:00
Rafał Miłecki
d0b50c2770 kernel: drop usbdev LED trigger
It was LEDE's trigger that was replaced by upstream usbport one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Rafał Miłecki
0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Felix Fietkau
a92f57599c ipq806x: add back end-of-UBI marker for a few factory images (FS#228)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-18 09:30:57 +02:00
Henryk Heisig
f5aa459043 ar71xx: Add support to TP-Link EAP120
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-18 09:18:55 +02:00
Matthias Schiffer
83f7ec31f8
ar71xx: set EU region code for TP-Link TL-WA901ND v4
There is no US firmware for the TL-WA901ND v4 yet, so we'll just
unconditionally set the EU region for now.

This makes LEDE flashable on these devices again. The format of the region
string is slightly different from the one used on the Archer C7 that is
generated by mktplinkfw (the second half of the region string is missing),
but it's similar enough to make it work.

Tested-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-15 19:09:56 +02:00
YuheiOKAWA
4050cfebda ramips: add support for Planex VR500.
SOC:	MT7621A
RAM:	256MiB
NOR:	MX25L51245G

Non Wireless Router.

Issue: soft reboot problem. SPI Flash do not exit 4byte address mode.

Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
2016-10-15 11:36:51 +02:00
Petr Štetiar
5a922e5c41 imx6: inittab: Use login.sh wrapper so we can configure console password
In dc92917 there was introduced login.sh wrapper which allows
configuration of console passwords via UCI system ttylogin config
option.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2016-10-15 11:36:51 +02:00
Christian Lamparter
098f7156cc ar71xx: add support for the Airtight C-60
This patch adds support for the Airtight C-60.

SOC:	Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM:	128 MiB
NOR:	MX25L3205D 4MiB
NAND:	ST Micro NAND 32MiB 3,3V 8-bit
SW-NET:	AR8327N (2 Ports)
WLAN1:	Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2:	Dual-Band AR9300 Rev:4 PCIe Chip

The switch is setup for an accesspoint:
	LAN1: (gigabit) is the wan-port.
	LAN2: (fast ethernet) is bridged with the br-lan.

Flashing Guide (via initramfs):
  1. Connect a PC to the serial port of the C-60.
     power up the C-60.

     Enter u-boot command prompt:
     #> nand erase
     #> setenv bootcmd "bootm 0x9f060000"
     #> saveenv
     #> setenv ipaddr 192.168.1.1
     #> setenv netmask 255.255.255.0
     #> setenv serverip 192.168.1.100
     #> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
     #> tftpboot
     #> bootm

  2. Wait for the C-60 to boot LEDE.
     On the root prompt. Enter:
     # ubiformat /dev/mtd4
     # ubiattach -p /dev/mtd4

  3. After that copy the sysupgrade.tar onto the router and run:
     # sysupgrade sysupgrade.tar

     to flash the image.

Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-15 11:36:50 +02:00
Christian Lamparter
e9455c561d generic: ar8216: improve ar8xxx_is_possible check
The commit "generic: ar8216: add sanity check to ar8216_probe"
(774da6c7a4) stated that PHY IDs
should be checked at address 0-4. However, the PHY 4 was
never check by the loop. This patch extends the check to be
similar to the Atheors SDK. It tries all 4 ports and skips
unconnected PHYs if necessary. If it cannot find any familiar
PHYs, it will prevent the phy driver from initializing.

This patch is necessary for the C-60. It doesn't have a
PHY at port 3, so this caused the check in ar8xxx_is_possible
to fail. As a result, the ethernet ports on the C-60 didn't
work.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-15 11:36:50 +02:00
Henryk Heisig
bcfb535730 ipq806x: C2600: change leds colour name
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Henryk Heisig
4bdf615878 ipq806x: add support for indicating the boot and upgrade state using four leds
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Mathias Kresin
36afaae847 lantiq: use wpad-mini for WBMR boards
The WBMR boards are the only ones in the whole tree selecting the wpad
and hostapd-utils package by default.

Remove the wps uci-default script as well, there is no obvious reason
why the wps config need to be set only for this board.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
335ccddc10 lantiq: fix ARV452CQW keys
Fix the typo in the gpio-keys-polled compatible string.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
bcfbeae79f ramips: use rfkill for wps button on wlan only boards
All of the touched boards don't have an ethernet port. Allow to use the
wps button on these boards to enable the wireless radio after boot.

The force enabled wireless for the DCH-M225 is removed. It is reckless
to bring up an unencrypted wireless network by default these days.

Using the wps button to bring up the radio seam to me the better
approach.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
0a219c8dfb ramips: use rootfs splitter and new image build code for BR-6475ND
Use the edimax uImage splitter instead of the fixed size rootfs
partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
e7ec5df33b ramips: move edimax images to the new build code
Images installed via TFTP recovery or the Edimax webinterface of the
3g-6200n(l) are writting with the edimax header to flash.

Use only one image type for these boards. The migration to the
factory only images need to be done via TFTP recovery.

Use the same start address for the 3g-6200n(l) factory images as the
stock firmware images.

Thanks to Jan Dostrasil for reporting all the issues of the 3g-6200nl
and the patient testing of all changes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
634d690d74 kernel: mtdsplit_uimage: fix Edimax parser
According to the author the code was added to in preparation for adding
support for a new board. The patch for the board was never send and the
code never really tested.

The edimax header starting with the edimax magic is put in front of the
uImage header. There is no special uImage header used. Means, default
magic and the type field is set to kernel as usual.

Signed-off-by: Mathias Kresin <dev@kresin.me>

edimax parser fix
2016-10-15 09:01:45 +02:00
Mathias Kresin
35073d47bb kernel: mtdsplit_uimage: fix rootfs offset
The return value of the find_header function need to be added to the
uimage_size, otherwise mtd_find_rootfs_from() might search for a rootfs
within a custom header and fails.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
6391af2f1f ramips: improve edimax 6200n/nl support
Assign the reset functionality to the wps/reset buttons. Use the wlan
switch of the 6200n to enable/disable wlan.

Add the internet led of the 6200nl and use the led for boot status
indication

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
51bca43f39 ramips: fix edimax 6200nl switch config
With 3a9752bbd2 and later changes to
ramips_set_preinit_iface() the default vlan config applied during
preinit was changed. These changes were made without updating the
default network config to ensure that vlan interfaces used for lan/wan
are still configured.

Fix the issue by using the default all LAN portmap and disabling not
connected switch ports using portdisable device tree parameter.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
bbdf2ac305 ramips: tag the CPU switch port
With de51026515 the explicit tagging of
the CPU port was removed. This leads to a not working default network
config, with vlans enabled but disabled CPU tagging, for boards where
all switch ports are having the same role.

In case the ports are having different roles set, tagging is is set
implicit for the CPU port by ucidef_add_switch().

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
b35dd9584e ramips: remove fixed lan/wan interface for switch configs
Don't set the lan/wan interface when using ucidef_add_switch. This
results into a wan interface albeit all ports a annotated as lan ports.

ucidef_add_switch takes care of setting the correct lan/wan interface
according to the annotation of the ports.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Álvaro Fernández Rojas
611399f1f8 brcm2708: fix image generation with imagebuilder
COPYING is not present in $(LINUX_DIR) on imagebuilder and prevents a
successful image creation.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-10-13 19:01:41 +02:00
Karl Palsson
5d04dcedb4 ar71xx: move dragino2 from legacy to generic
Tested on real hardware with r1804.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2016-10-13 17:04:38 +02:00
Christian Lamparter
4fc48a8cf2 apm821xx: replace recovery image for the MBL with initramfs
The patch "images: bump default rootfs size to 256 MB"
a1f83bad60 caused a crash
during boot for the recovery images. This is because
both variants of the MyBook Live only have 256MB of RAM
and for the recovery option, the ext4 rootfs was simply
stored in the RAMDISK.

This patch replaces recovery image for the MBL with an
initramfs kernel.

In order to boot the initramfs (for recovery or development):

0. copy the initramfs and device tree into tftp's server directory
   # cp *-initramfs-kernel.bin to /tftp-server/mbl.bin
   # cp *-ext4-kernel.dtb to /tftp-server/fdt.bin

1. Connect the MyBook Live (Duo) serial port.
   (Warning! Use a 3.3v level shifter).

2. Hit Enter during u-boot and insert these three lines:
   # setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1;
   # tftp ${kernel_addr_r} mbl.bin; tftp ${fdt_addr_r} fdt.bin
   # run addtty addmisc; bootm ${kernel_addr_r} - ${fdt_addr_r}

   Where 192.168.1.254 is your TFTP server.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-13 17:04:33 +02:00
Yousong Zhou
d1000f81a8 x86: 64: enable pci hotplug and acpipnp
This will allow dynamically adding/removing at least virtio-net pci
devices which are quite the norm in cloud environment with QEMU/KVM

    netdev_add bridge,id=wan2,br=br-wan,helper=/home/yousong/.usr/libexec/qemu-bridge-helper
    device_add virtio-net-pci,id=devwan2,netdev=wan2,mac=11:22:33:22:11:00

The config was formed by selecting target x86/64 first, then select
CONFIG_HOTPLUG_PCI and CONFIG_HOTPLUG_PCI_ACPI with

    make kernel_menuconfig CONFIG_TARGET=subtarget

The following text tries to explain how the current config was formed

 1. CONFIG_PCI_LABEL and CONFIG_ATA_PIIX were removed because they were
    already enabled in x86 platform config
 2. CONFIG_ATA_SFF was removed because it was enabled in generic config
 3. CONFIG_NLS was removed because it will be selected by CONFIG_PCI_LABEL

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2016-10-13 17:04:26 +02:00
Álvaro Fernández Rojas
87b2b89959 tools: remove old mkdosfs symlink from dosfstools
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-10-12 11:59:09 +02:00
Florian Beier
5abeba3450
ar71xx: add userspace support for D-Link DIR-869 A1, generate images
Signed-off-by: Florian Beier <beier.florian@gmail.com>
[Matthias Schiffer: fix factory image, improve commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:37 +02:00
Matthias Schiffer
594f0e80ce
ar71xx: add kernel support for D-Link DIR-869 A1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:36 +02:00
Matthias Schiffer
e407f1a4c8
ar71xx: add back SEAMA header checksum fix (as used on ramips)
The D-Link DIR-869 A1 doesn't accept images with the jffs2 marker added
after the checksummed range, so we need to include it in the checksum and
fix it on first boot.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 20:57:59 +02:00
Matthias Schiffer
212ce6bce1
ar71xx: avoid double lzma compression of kernel for SEAMA images
Use relocation loader instead of lzma loader.

Tested on D-Link DIR-869 A1.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 20:57:51 +02:00
Matthias Schiffer
0d1fb72241
ar71xx: add relocation loader
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 20:39:16 +02:00
Matthias Schiffer
fce0b5d893
ar71xx: clean up SEAMA image build code
Split seama-factory and seama-sysupgrade into smaller pieces (similar to
the ramips code) to make the image generation more flexible.

Also use standard pad-offset instead of adding a block of zeros at the
beginning of the image that is later cut off again. Standard pad-rootfs can
be used as the seal header doesn't contain an image size or checksum.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 20:32:24 +02:00
Mathias Kresin
0547b3ca64 lantiq: fix lantiq-dsl output spam
In case the adsl/vdsl service is disabled intentional, the output is
cluttered with the following message multiple times if the status of
the dsl line is queried:

  killall: vdsl_cpe_control: no process killed

If the dsl line status is queried by LuCI, the logfile is spammed with
the message.

Fix the issue by using killall in quite mode. In quite mode killall
still returns a non-zero value if the to be killed process can not be
found so that existing logic based on the return value still works.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-11 09:31:57 +02:00
Amir Rachum
4c36bcc567
ar71xx: build image for Archer C7 v2 IL
TP-Link uses a different region coding mechanism for IL firmware for the Archer
C7 v2. Instead of of setting the region, they set a different TPLINK_HWREV.

Signed-off-by: Amir Rachum <amir@rachum.com>
2016-10-09 21:13:09 +02:00
Mathias Kresin
993ca3b747 lantiq: fix BTHOMEHUBV2B default packages
Due to the introduced double whitespace the default package selection
isn't applied. This leads to errors like a not working networking
because of a missing swconfig binary.

Fixes FS#208.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-06 22:58:50 +02:00
Ben Whitten
6638946f99 at91: Remove u-boot from platform images folder
Removes the bootloader from the images section as its now in packages/boot
with the others.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
2016-10-06 12:15:13 +02:00
Pavel Kubelun
9677bfbb0f ipq806x: fix wlan mac for Netgear R7800
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-10-06 08:01:33 +02:00
Mathias Kresin
116adaa3a4 lantiq: fixup last commits
Revert the rename of unrelated device tree nodes. Rename the missed
leds of the Speedport W 504V Typ A.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-05 20:26:35 +02:00
Mathias Kresin
7659f9ad9e lantiq: fix usb leds/trigger
Add USB led aliases to boards having an led which is meant to be used
as USB led according to the manuals.

Remove the kmod-ledtrig-usbdev from the default package selection for
boards not having an USB led. Add the kmod-ledtrig-usbdev to boards
where it is missing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-05 19:23:23 +02:00
Mathias Kresin
e07c80dfc8 lantiq: use aliases device tree node for leds
The chosen node is clearly the wrong place for aliases.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-05 19:23:23 +02:00
Mathias Kresin
8b639410d1 lantiq: cleanup led handling functions
Use a more generic name for the lantiq_get_dt_led_chosen function.

Drop the lantiq_is_dt_led_chosen function. The lantiq_get_dt_led
function can be used to achieve the same.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-05 19:23:23 +02:00
Mathias Kresin
dbb13a81b9 lantiq: board.d: apply alphabetical order to led file
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-05 19:23:23 +02:00
Jo-Philipp Wich
27dc933827 zynq: fix maintainer email address
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-05 01:18:24 +02:00
Jo-Philipp Wich
a1248daddf zynq: convert to new image build code
Convert the Zynq target to use the new image build code in order to fix
broken image generation after 9945a1dca5
changed the handling of CPIO images.

Also remove the misapplied ubifs feature flag since the image generation is
not using UBIFS for building FIT images.

As part of the conversion, move the DTB building and the uImage ramdisk
generation into separate build steps which can be generalized and shared
with other targets, like APM821xx, in the long run.

Also remove the legacy profile declarations and use new-style per-device
profiles which will allow different package sets per image in the future.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-05 01:18:02 +02:00
Felix Fietkau
c34676f4d4 kernel: add missing config symbol (partial forward port of d2f4479870)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-04 17:54:35 +02:00
Felix Fietkau
8a7a1b0029 kernel: add missing symbols for Linux 3.18 (like d2f4479870)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-04 17:07:59 +02:00
Jo-Philipp Wich
d2f4479870 kernel: add missing symbols for Linux 4.1
Add some missing symbols to the generic 4.1 kernel config which got triggered
by the introduction of the hda-intel sound module.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-04 16:00:01 +02:00
Rafał Miłecki
a69e19d18a kernel: backport usbport LED trigger from 4.9
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-04 12:08:25 +02:00
Klaus
df5416296c ramips: add support for Zyxel NBG-419N2 (WAP3205v2)
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files

Signed-off-by: Klaus <k-laus@quantentunnel.de>
2016-10-04 11:50:51 +02:00
Piotr Dymacz
52974da2bb ar71xx: update kernel config symbols
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:51 +02:00
Piotr Dymacz
c166b050fd ar71xx: base-files: fix boards order in lib/upgrade/platform.sh
Keep also case sections in alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
8be47007a9 ar71xx: base-files: cleanups in lib/upgrade/platform.sh
This includes:

- code style fixes
- fix boards order within case sections

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
92870eac27 ar71xx: comsetic cleanups in files/arch/mips/ath79/{Makefile,machtypes.h}
Keep everything in alphabetical order and aligned in columns.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
6e58440fc1 ar71xx: base-files: cleanups in etc/board.d/01_leds
This includes:

- use of local 'board' variable in LED names, wherever possible
- merge of boards with exactly the same LED configuration

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
c142df3094 ar71xx: fix LED names for GL Innovations boards
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
8689078a9b ar71xx: base-files: fix code style in etc/board.d/01_leds
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
d09f4e0631 ar71xx: base-files: combine boards with the same config in etc/diag.sh
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
2917ae91ec ar71xx: base-files: cleanups in etc/diag.sh
This includes:

- code style fixes
- use of local 'board' variable in LED names, wherever possible

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
edcdb93467 ar71xx: base-files: fix boards order in etc/board.d/02_network
Keep everything in alphabetical order. Boards are ordered in two steps,
first within/inside common configuration (case section), then sections,
globally.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
a75cfac1f6 ar71xx: base-files: cleanups in etc/board.d/02_network
This includes:

- code style fixes
- removal of huge comment (it should be in doc, not here) and some small ones
- removal of redundant config for DR531/WPJ531 as the default is the same
- merge of boards with exactly the same interfaces config

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:49 +02:00
Piotr Dymacz
4fa90c49c1 ar71xx: base-files: rework etc/board.d/02_network
Convert etc/board.d/02_network in ar71xx target to the same shape
as we have in ramips target. Split code into two new functions:

- interface/s setup in ar71xx_setup_interfaces()
- MAC/s setup in ar71xx_setup_macs()

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:48 +02:00
Aaron Curley
15cb19f02a mvebu: fix sysupgrade
sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output:
	Switching to ramdisk...
	Performing system upgrade...
	ash: /usr/sbin/fw_printenv: not found
	ash: fw_setenv: not found
	ash: touch: not found
	cannot find target partition

Fixes FS#197.

Signed-off-by: Aaron Curley <accwebs@gmail.com>
2016-10-04 11:50:48 +02:00
Xuefu Lin
dce5c4f5c8 ramips: Add support for Phicomm K2 PSG1218
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet

Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
2016-10-04 11:50:46 +02:00
Hauke Mehrtens
8370b9eede ntiq: make i2c-lantiqi driver compile again
It missed some changes needed for kernel 4.4. This is only used by the
Falcon SoC and not for the xRX SoCs.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-10-03 00:13:11 +02:00
Rafał Miłecki
ba1024b9c9 bcm53xx: use the latest XHCI doorbell patch sent for upstream
The main difference is it supports DT binding. This allows us to use DT
for specifying controller and the new standalone USB 3.0 PHY driver.
Thanks to that we don't need out of tree patch adding PHY initialization
to the controller driver anymore.
2016-10-02 00:22:57 +02:00
Rafał Miłecki
28974de663 bcm53xx: drop unneeded fix for usb3-lpm-capable DT property
This problem has been fixed by upstream commit 757de492f2d ("xhci: fix
platform quirks overwrite regression in 4.7-rc1").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-01 19:18:05 +02:00
Rafał Miłecki
d7e41df24a bcm53xx: switch to standalone USB 2.0 PHY driver
This drops built-in support for USB 2.0 PHY and starts using separated
driver that was upstreamed & backported some time ago.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-01 16:52:08 +02:00
Rafał Miłecki
7120a43013 bcm53xx: add patch specifying USB controllers in DT
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-01 16:52:08 +02:00
Rafał Miłecki
d5dcb1bf97 bcm53xx: backport BCM5301X patches from 2019-09-30
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-09-30 23:39:28 +02:00
Matthias Schiffer
cea09329e5
netfilter: fix file conflicts between kmod-ipt- and kmod-nft- packages
The nf_reject_* and nf_nat_masquerade_* modules are moved into the
corresponding kmod-nf- packages. Appropriate dependencies are added to the
kmod-nft- packages.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-30 23:32:05 +02:00
Álvaro Fernández Rojas
7d559169c5 kernel: update to v4.4.23
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-30 20:08:21 +02:00
Stijn Segers
949cfbb243 kernel: update kernel 4.4 to version 4.4.22
Forgot to update kernel-version.mk, so updated patch. Compile-tested on x86/64 and ar71xx; run-tested on x86/64 and ar71xx.

Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-09-30 13:34:04 +02:00
dissent1
eb7307cb94 ipq806x: update Netgear R7800 device tree
-add spi pins
-move mdio and rgmii pinctrl from gmac and mdio into pinmux node
-add i2c4 pinctrl into rpm node
-add pin details into several nodes
-update gmac1 and gmac2 parameters
-update mdio phy0 and phy4 registers by ddwrt devs findings
-fix i2c4 pin drive-strengh
-remove pcie pins as it's already present in ipq8065 DT

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-09-30 10:15:23 +02:00
Álvaro Fernández Rojas
c3d3111831 brcmfmac43430-firmware: remove package and switch to linux-firmware
Now that the firmware for BCM43430 has been submitted to linux-firmware use it
and remove RPiDistro package.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-29 21:24:45 +02:00
Felix Fietkau
0b828e3249 kernel: add missing config symbols
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-29 18:07:47 +02:00
Jonas Gorski
4aa5d3e60d mvebu: add support for SFP
Add patches for SFP support and package it for ClearFog. Tested with a
Juniper SFP module.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-29 13:47:18 +02:00
Jonas Gorski
a454756c91 mvebu: disable MSI interrupts
MSI interrupts do not seem to be working on mvebu, and they break
ath10k. Since nothing else seems to be using them, especially not
mwlwifi, disable them until we can fix MSI interrupts.

Works around the following issue:
[    9.001457] ath10k_pci 0000:02:00.0: failed to receive control response completion, polling..
[   10.001453] ath10k_pci 0000:02:00.0: Service connect timeout
[   10.007126] ath10k_pci 0000:02:00.0: failed to connect htt (-110)
[   10.092224] ath10k_pci 0000:02:00.0: could not init core (-110)
[   10.098177] ath10k_pci 0000:02:00.0: could not probe fw (-110)

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-29 13:47:18 +02:00
Cezary Jackiewicz
e79e555c0e ramips: Xiaomi MiWiFi Nano: fix status led
- add status led for Xiaomi MiWiFi Nano
- revert af1e70b4a7 , this should not be added.

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-09-29 11:39:41 +02:00
Felix Fietkau
2b3b63aea3 kernel: fix build error in sign-file.c with libressl
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-29 11:23:27 +02:00
Felix Fietkau
9f6d8532c7 kernel: add missing config symbols
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-29 11:13:31 +02:00
Felix Fietkau
71144844e1 kernel: add missing config symbols
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-28 16:59:34 +02:00
Martin Blumenstingl
e7be0decf6 ar71xx: Do not use a hardcoded ath10k firmware mac address
ar71xx has an init-script for special devices where the ath10k OTP
calibration data is stored on the PCIe card's EEPROM (and thus can only
be read by ath10k). Unfortunately the OTP data uses the default mac
address (= all devices come with the same mac address, which leads to
problems when you have multiple of these devices in the same network).

To work around this the mac address is patched in the firmware during
the first boot of the device. To prevent flash wear this was only done
if the ath10k firmware matched a hardcoded md5sum.
However, if the md5sum does not match this can mean that either the mac
address was already patched (which is fine) - unfortunately it can also
mean that the firmware version was updated without updating the
hardcoded md5sum.

Change the "was the mac address already patched" check to actually
compare the mac address inside the ath10k firmware.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-09-28 08:39:01 +02:00
Felix Fietkau
96b59dc383 kernel: add missing config symbol after rfkill change
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-28 08:37:44 +02:00
John Crispin
986ec56507 rfkill: add fake rfkill support
allow building of modules depending on RFKILL even if RFKILL is not enabled.

Signed-off-by: John Crispin <john@phrozen.org>
2016-09-27 20:27:26 +02:00
Chris Blake
68d649f5cd ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker Gateway
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-09-27 17:50:22 +02:00
BangLang Huang
142ec7ada9 ramips : add support for Newifi D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
BangLang Huang
9fe833e1d0 ramips : add support for PandoraBox D1
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2016-09-27 17:50:22 +02:00
Adrian Panella
dd1b69a058 uml: set inittab for working console
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-09-27 17:50:21 +02:00
Cezary Jackiewicz
66aae9a271 ramips: Add support for ZBT-CPE102
- CPU: MT7620N 580MHz
- Flash: 8MB
- RAM: 64MB
- build-in minipcie slot for modem 3G/4G
- one ethernet port 10/100Mbps

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-09-27 17:50:21 +02:00
Matthias Schiffer
43bf3e80b2
ramips: fix DEVICE_PACKAGES of Ubiquiti EdgeRouter X
kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on
kmod-cfg80211. kmod-rt2800-pci should not be installed anyways.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-26 17:57:57 +02:00
Matthias Schiffer
9dbf8241c3
ar71xx: clean up DEVICE_PACKAGES of legacy devices
Remove arbitrary or redundant packages from DEVICE_PACKAGES.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-26 17:57:57 +02:00
Jonas Gorski
27ed4e9c14 mvebu: add switch config for clearfog pro
Check for switch0 existance and add default switch config if found.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2016-09-26 13:27:44 +02:00
Jonas Gorski
6859098d97 mvebu: add sysupgrade support for clearfog
Add and enable sysupgrade support for clearfog boards, based on how the
brcm2708 target does it.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-26 13:04:53 +02:00
Jonas Gorski
c359d7e81b mvebu: add switch node to clearfog
Add a switch node to clearfog to probe and initialize it on Clearfog
Pro. This make the switch work and allows using all six switch ports.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-26 13:04:47 +02:00
Jonas Gorski
167763837b mvsw61xx: enable SerDes on 6176 if required
If the cpu port is connected through SGMII we need to enable SerDes for
it to work.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-26 13:04:04 +02:00
Jonas Gorski
92dcaecee3 mvsw61xx: reset phys on probe to enable switch ports on clearfog pro
The clearfog u-boot does not initialize the switch at all, so we need to
power up the phys ourselves.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-26 13:03:58 +02:00
Jonas Gorski
f2102b484b mvebu: replace ClearFog dts files with patches from upstream
Make the dts file match with what is upstream, to ensure it has the
latest changes and switching to newer kernels is easier.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-26 13:03:51 +02:00
Jonas Gorski
c4f4d65835 mvebu: enable PCA955x driver for clearfog to enable pcie and usb
Some of the PCIe and USB signals use a GPIO expander on I2C on ClearFog,
so enable the driver so that they can be configured to their required
values.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-26 13:03:45 +02:00
Jonas Gorski
d8075b15d0 uboot-mvebu: make hidden and be m for clearfog to fix IB failing to add it
Uboot-mvebu isn't a real package, which will break the image builder
when it tries to install it during the packing step. Instead of cleafog
selecting it through its default packages, make it default to m if the
clearfog profile is selected.

This will ensure it is always build, but never added to the rootfs. This
fixes creating images for clearfog with IB.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-26 12:48:18 +02:00
Jonas Gorski
bc1f006b4e uboot-mvebu: also install into KDIR to ensure it packaged in IB
The clearfog image requires u-boot, so package it into KDIR to make sure
it is available in imageBuilder.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
2016-09-26 12:47:36 +02:00
Matthias Schiffer
175fbe4d4e
ramips: move /lib/ramips.sh include in /etc/init.d/bootcount into start()
Enabling the init script offline will print an error otherwise.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-25 23:26:42 +02:00
Neal Oakey
524d4110f9
ar71xx: add model detection for many Ubiquiti AirMax XM devices
Signed-off-by: Neal Oakey <neal.oakey@bingo-ev.de>
[Matthias Schiffer: minor adjustments]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-24 19:07:27 +02:00
Jo-Philipp Wich
1c09849f6c treewide: remove bad local shell variable declarations
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-09-24 14:38:20 +02:00
Martin Blumenstingl
d72e838429 ramips: do not "local" variables outside of a function
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-09-24 01:17:18 +02:00
Martin Blumenstingl
e9de6e5203 lantiq: do not "local" variables outside of a function
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2016-09-24 01:17:17 +02:00
Rafał Miłecki
1ac5cf7713 bcm53xx: move BCM53573 USB 2.0 patch to use backports prefix
It was pushed into the usb-next branch.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-09-21 14:20:20 +02:00
Christian Lamparter
e9401a2335 kernel: owl-loader for delayed Atheros ath9k fixup
Some devices (like the Cisco Meraki Z1 Cloud Managed Teleworker Gateway)
need to be able to initialize the PCIe wifi device. Normally, this is done
during the early stages of booting linux, because the necessary init code
is read from the memory mapped SPI and passed to pci_enable_ath9k_fixup.
However,this isn't possible for devices which have the init code for the
Atheros chip stored on NAND in an UBI volume. Hence, this module can be
used to initialze the chip when the user-space is ready to extract the
init code.

Martin Blumenstingl made a few fixes and added support for lantiq:
kernel: owl-loader: add support for OWL emulation PCI devices
kernel: owl-loader: don't re-scan the bus when ath9k_pci_fixup failed
kernel: owl-loader: use dev_* instead of pr_* logging functions
kernel: owl-loader: auto-generate the eeprom filename as fallback
kernel: owl-loader: add a debug message when swapping the eeprom data
kernel: owl-loader: add missing newlines in log messages
kernel: owl-loader: add support for the lantiq platform

These patches have been integrated. Thanks!

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2016-09-19 19:32:35 +02:00
Piotr Dymacz
dc9172b65b ar71xx: update kernel config symbols
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-09-19 15:30:32 +02:00
Piotr Dymacz
2ad0ecc101 ar71xx: mark U-Boot and radio calibration data partitions as read-only
General convention is to keep U-Boot and radio calibration
data (ART) mtd partitions marked as read-only.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-09-19 15:30:32 +02:00
bobafetthotmail
b9a55277d5 kirkwood: fix uimage creation for some kirkwood devices
because with the current system I'm getting fake uImages that are actually a
renamed zImage, and that's plain wrong.
This fixes bug https://bugs.lede-project.org/index.php?do=details&task_id=131
and https://bugs.lede-project.org/index.php?do=details&task_id=139

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2016-09-19 15:30:32 +02:00
Felix Fietkau
0b3a64f862 cns3xxx: eliminate hardcoded kernel/rootfs partition split
This changes the sysupgrade format. To support upgrades from the old
firmware to the new one, legacy images are provided. Because of the old
partition split, these have to be specific to the NOR or SPI device.

The new sysupgrade images are suitable for begin put on flash directly,
and they are independent of NOR vs SPI flash variant.

Flashing back to old firmware is supported via using the old full-flash
images instead of the old sysupgrade images.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-19 14:27:26 +02:00
Felix Fietkau
58fbe07560 cns3xxx: move laguna.c changes out of patches, update it in files/
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-19 14:27:26 +02:00
Felix Fietkau
413eb04e1e ubifs: add full overlayfs support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-19 14:27:26 +02:00
Rafał Miłecki
41a582a986 bcm53xx: use upstream accepted ILP clk driver for BCM53573
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-09-17 21:43:29 +02:00
Álvaro Fernández Rojas
8c52fbbe3a arm64: fix build for linux 4.4.21
linux 4.4.21 adds 2 new symbols for arm64.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-16 12:11:10 +02:00
Álvaro Fernández Rojas
41eab9048b kernel: update kernel 4.4 to version 4.4.21
Refresh patches for all targets that support kernel 4.4.
Compile-tested on brcm2708 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-16 10:17:27 +02:00
Álvaro Fernández Rojas
a530196f8d sunxi: add rtl8xxxu into pcduino v3 profile
Now that RTL8188EU is supported in rtl8xxu select it for pcDuino v3

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-15 20:23:46 +02:00
Álvaro Fernández Rojas
ba5a9aba5c brcmfmac43430-firmware: rename to brcmfmac-firmware-43430-sdio
This is consistent with the rest of brcmfmac firmwares.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-15 20:23:46 +02:00
Matthias Schiffer
01e2024754
ar71xx: set region code of TP-Link TL-WDR3600/4300 to US
There are currently two stock firmwares for the TL-WDR3600/4300, a US and
a universal version. Both allow installing images with US region code, so
we don't need to provide multiple images.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-15 19:34:28 +02:00
Matthias Schiffer
b063faa2c8
ar71xx: separate TP-Link TL-WDR3600/4300/4310 profiles
Simplify modifying some of the images without affecting the others.

While we're at it, also unify the profiles to use := syntax and add "v1" to
the TL-WDR4300 name to make things more consistent.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-09-15 19:33:30 +02:00
Koen Vandeputte
88ee275562 cns3xxx: Enable driver support for onboard m25p80 SPI flash
This device is present on the Gateworks Laguna cns3xxx family.

As the SPI bus master is enabled, also enable driver support for
this typical slave.

[    3.920000] m25p80 spi1.0: found m25p32, expected m25p80
[    3.930000] m25p80 spi1.0: m25p32 (4096 Kbytes)
[    3.930000] Creating 4 MTD partitions on "spi1.0":
[    3.940000] 0x000000000000-0x000000040000 : "uboot"
[    3.940000] 0x000000040000-0x000000080000 : "params"
[    3.950000] 0x000000080000-0x000000200000 : "kernel"
[    3.950000] 0x000000200000-0x000000400000 : "rootfs"

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-09-15 13:11:21 +02:00
Tim Harvey
dc17fde994 kernel: clean up usb gadget support
clean up usb gadget support:
- rename gadget modules so that they appear together and are easier to
  identify as gadget modules
- make usb-lib-composite and usb-gadget hidden as there is no point in
  selecting those without gadget drivers that require them as deps

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2016-09-15 13:11:21 +02:00
Mathias Kresin
eb88a9cacb ramips: fix wrong blocksizes
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.

I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.

The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.

Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-15 09:53:37 +02:00
Álvaro Fernández Rojas
d14c28fc80 kernel: update kernel 4.4 to version 4.4.20
Refresh patches for all targets that support kernel 4.4.
Compile-tested on brcm2708 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-15 08:10:55 +02:00
Mathias Kresin
925e63e71f ramips: enable 4K sector support in kernel config
This is a follow up to 28110727f1
"ramips: set blocksize for 4MB devices". I've missed to include the
required changes of the kernel configs to enable 4K sector size
support.

The option is only enabled for targets having boards with 4k sector
size flash chips.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-13 22:06:08 +02:00
Mathias Kresin
61c2a7339a image: remove padding parameter from append-kernel/append-rootfs
Using pad-to instead of passing the optional padding to append-kernel
or append-rootfs. It could be that the value of a variable is passed.
In case the variable is empty no error is thrown.

Furthermore the purpose of the extra parameter is hard to get without
reading the code.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-13 19:36:41 +02:00
Mathias Kresin
1cd0a4c688 image: add KERNEL_SIZE to the default device vars
This reverts commit ec37a56587 and fixes
the underlying issue.
2016-09-13 19:36:41 +02:00
Rafał Miłecki
b964196c68 bcm53xx: use the latest submitted version of ILP clock driver
It switched to syscon to better describe PMU block.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-09-13 12:25:50 +02:00
Rafał Miłecki
2c38b6e076 bcm53xx: specify brcmfmac firmware for every device
This will allow us to include required firmwares only and save some
rootfs space.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-09-13 11:03:43 +02:00
Daniel Gimpelevich
993ad29359 kernel: Backport pending appended DTB handling patches
Backport patches from upstream Linux kernel which are making the
kernel stores the appended dtb not in the same resisters as defined in
the UHI specification, use a separate variable on MIPS.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[some modifications]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-09-12 22:36:55 +02:00
Felix Fietkau
d27bce8d28 build: drop UBI EOF marker from images by default
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-12 18:21:52 +02:00
Mathias Kresin
c7d5bc8197 ramips: improve Linksys EA8500 build code
Use of the kernel size variable.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-11 19:40:45 +02:00
Mathias Kresin
306f1c7846 mvebu: fix OpenBlocks AX3 image
The KERNEL_SIZE variable is unset and no padding is applied. This looks
like a typo to me since the ubinized image need to be aligned to the
flash blocksize.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-11 19:40:45 +02:00
Mathias Kresin
ec37a56587 ar71xx: fix typo in image build code
The kernel size isn't passed to the append-kernel build step and the
resulting image bricks the device.

Fixes FS#168.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-11 19:40:45 +02:00
Mathias Kresin
c1578d4fc9 cleanup ucidef_set_interface* usage
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:32:25 +02:00
Mathias Kresin
92eaf27c62 use immediate set in target Makefiles
No functional change, it's just to have the same style everywhere. This
way I don't need to use any regex magic to extract all subtargets for
compile tests.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:30:38 +02:00
Mathias Kresin
0f6d0afa13 ramips: board.d merge redundant switch/interface configs
Fix alphabetical order distortions as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:28:38 +02:00
Mathias Kresin
64d72880bc lantiq: board.d: apply alphabetical order
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:28:38 +02:00
Mathias Kresin
96f6bd501a lantiq: board.d: cleanup default switch config
Add or fix the physical port number of switch ports to allow LuCI to
display the ports in physical order.

Remove the physical port number in case bridge port and physical port
order are the same.

Reorder the ucidef_add_switch parameter to be aligned with the switch
port number.

Remove board settings which are covered by the default case and remove
comments.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:28:38 +02:00
Mathias Kresin
7d02e94e41 lantiq: enable cpu temp driver for more tested boards
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-10 15:28:38 +02:00
Álvaro Fernández Rojas
2b1c6b21b5 brcm2708: update linux 4.4 patches to latest version
As usual these patches were extracted and rebased from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.4.y

Also adds support for Raspberry Pi Compute Module 3 (untested).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-09-10 14:54:26 +02:00
Felix Fietkau
ca356887ed x86: disable MTD support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Felix Fietkau
fe24545982 octeon: remove block2mtd support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Felix Fietkau
d2a7df0792 octeon: use new ext4/f2fs overlay support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Felix Fietkau
08cf46123f octeon: enable f2fs and loopback device support in the config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Felix Fietkau
9d57957784 octeon: enable f2fs and ext4 utilities
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Felix Fietkau
3cbb7820a4 mvebu: use ext4/f2fs overlay filesystem for solidrun clearfog
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Felix Fietkau
bee30de984 mvebu: enable ext4, f2fs and loop device support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Felix Fietkau
be59b1718d x86: drop the use of block2mtd, use ext4/f2fs as overlay filesystem
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Felix Fietkau
c6eb09d5a3 x86: enable mkf2fs and e2fsprogs by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Felix Fietkau
580f24bc96 x86: enable f2fs and loopback device support in the kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-09-10 12:17:39 +02:00
Koen Vandeputte
d70b748942 imx6: Add static PCA953x support in kernel
commit a2386c384d requires the
module to be static in the kernel.

So lets actually add support for it inside the kernel config.
Tested on Ventana

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-09-10 12:17:39 +02:00
Mathias Kresin
7d9ef9080c ramips: set blocksize for remaining rt3883 devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 21:03:57 +02:00
Mathias Kresin
9f531efc59 ramips: remove old build code seama recipe
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 15:27:46 +02:00
Mathias Kresin
fb39b77ccb ramips: switch DIR-610 A1 to new image build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-08 22:21:23 +02:00
Mathias Kresin
bd39104e95 ramips: switch some rt3883 devices to new build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 10:18:31 +02:00
Mathias Kresin
0f3600ccee ramips: move seama build recipe to Makefile
The identical build step is defined twice. Move it to the parent
Makefile to use only one version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:43:31 +02:00
Mathias Kresin
74da44cfc2 ramips: switch DIR-615 H1 to new image build code
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-02 07:34:36 +02:00
Mathias Kresin
483fd5f6ad ramips: add build recipe for senao header
Add it to the Makefile to allow a board which will be supported soon
to use the recipe as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-08-17 07:49:34 +02:00
Mathias Kresin
28110727f1 ramips: set blocksize for 4MB devices
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.

Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.

The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.

For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:

  - Ralink V11ST-FE
  - Ralink AP-RT3052-V22RW-2X2
  - MediaTek MT7628 EVB
  - MediaTek MT7621 EVB
  - UPVEL UR-326N4G
  - Buffalo WZR-AGL300NH

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-03 09:56:35 +02:00
Mathias Kresin
05ab2323ff ramips: don't set the same max image size twice
The ralink_default_fw_size_8M is already set for the default device.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-09-04 10:04:20 +02:00