Set it to the filesystem which is build. mktplinkfw need to know which filesystem
is used.
FILESYSTEM can be squashfs, jffs2-64k, ...
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 44997
Should fix pcmcia on BCM6348 and BCM6358 after switching to DT-probed
gpio controllers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44995
Fixes the following issue:
drivers/gpio/gpio-bcm63xx.c: In function 'bcm63xx_gpio_probe':
drivers/gpio/gpio-bcm63xx.c:80:4: error: implicit declaration of function 'devm_kasprintf' [-Werror=implicit-function-declaration]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44986
Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 44985
Currently there isn't images ready for flashing liveboxes boards. This
patch adds a script and the code to call it in the bcm63xx images
builder makefile to generate the livebox 1 firmware.
I removed some lines to avoid generating unneded files in the bin/ dir
for this board. And added code to generate a squashed rootfs aligned to
64 kB since the current one in the /bin dir is 128 kB aligned and
doesn't work. Still no sysupgrade support for this board. Upgrading from
within openwrt can be done writing with mtd the kernel, and then the 64k
aligned rootfs.
Regards
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: use sed instead of a separate shell script for the boot script, make it
respect the load address]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44982
The rework of the host tools discovery caused automake to embed
absolute paths to staging_dir/host/bin/perl into the shebang
of the generated automake executables.
Switch to the portable "/usr/bin/env perl" and enable global
warnings through "$^W" instead of the "-w" interpreter argument.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44972
The rework of the host tools discovery caused autoconf to embed
absolute paths to staging_dir/host/bin/perl into the shebang
of the generated autoconfig executables.
Switch to the portable "/usr/bin/env perl" and enable global
warnings through "$^W" instead of the "-w" interpreter argument.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44971
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44969
Helpful to disable when debugging lldpd crashes (when working on it).
When privilege separation is on, some crashes are stack-traced to
some privilege separation code.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 44967
