This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47876
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47875
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
Because of dsl-vrx200-firmware-xdsl-* there's no need anymore to
download a dsl firmware at runtime.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47851
The switch to uci-defaults-new.sh revealed a bug in the former used
uci-defaults.sh, which failed to add leds with colons in the led name.
This bug isn't any longer present in uci-defaults-new.sh and therefore
all via DT defined leds will be added to /etc/config/system with their initial
on/off state, regardless whether they are already added by the board specific
led mappings.
This results for a BTHOMEHUBV5A into the following led configuration:
- soc:blue:power is added as led_power with the initial state "switched on"
- soc:blue:power is added as led_soc_blue_power with the initial state "switched off"
With the final result of a switched off power led after boot.
The only led that needs to be added is the BTHOMEHUBV5A specific dimmed led.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47850
This patch just extends target/linux/ar71xx/image/Makefile to build
images also for version 2.1 of TL-WR710N
patch against the latest git
Signed off by: Norbert Wegener <nw@wegener-net.de>
SVN-Revision: 47849
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47848
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.
The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 47844
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47843
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.
This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47842
This resolves compilation warnings like this:
drivers/gpio/gpio-mt7621.c: In function 'mediatek_gpio_probe':
drivers/gpio/gpio-mt7621.c:328:46: warning: passing argument 2 of 'irq_set_chained_handler' from incompatible pointer type [-Wincompatible-pointer-types]
irq_set_chained_handler(mediatek_gpio_irq, mediatek_gpio_irq_handler);
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47841
Change the case switch to reflect the value used in the corresponding
device tree file.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47833
Use kernel arch for dts compilation.
Also use Image/BuildDTB to build dts for ramips.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47823
This replaces old bcm53xx patch for scanning whole flash and makes
bcm47xxpart compatible with NAND.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47800
