Commit graph

154 commits

Author SHA1 Message Date
John Marrett
4531bc4267 ramips: fix GL-inet GL-MT300N-V2 WAN/LAN MAC address
Correct MAC address lookup to appropriate offset based on vendor
source.

Override the WAN MAC to use the same address as LAN. The switch driver
increments the base MAC address for the WAN vlan but the stock firmware
uses the same MAC address for all interfaces.

Based on vendor source commit
https://github.com/domino-team/lede-1701/commit/efb0518

Signed-off-by: John Marrett <johnf@zioncluster.ca>
2017-07-15 07:02:59 +02:00
Piotr Dymacz
24043a0d2e ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.

The difference between these two models is in number of available
LEDs, buttons and power input switch.

This work is partially based on GitHub PR#974.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
  switch

* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Factory image notes:

These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.

We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.

Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.

The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".

Flash instruction:

Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

To access U-Boot CLI, keep pressed "4" key during boot.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Pavlo Samko
82f9486142 ramips: add support for TRENDnet TEW-638APB V2
This patch add support for the TRENDnet TEW-638APB V2.

Specification:
- SoC: Ralink SoC RT3052F
- Flash: 4MB
- RAM: 32MB
- Ethernet: 1x LAN (100 Mbps)
- Wireless: 2.4GHz b/g/n, 2x external antenna
- Buttons: 1x Reset, 1x WPS
- LEDs: Power (green), Ethernet (green), WPS (green and orange),
  Wireless (green)
- UART: 1x UART on PCB (3.3V, GND, RX, TX) - 57600 8N1

Installation

via vendor firmware:
- upload sysupgrade.bin image

via TFTP:
- stop uboot into tftp-load into option "2"
- upload sysupgrade.bin image

Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
2017-06-17 15:38:19 +02:00
Sven Roederer
9715beb04c ramips: add support for Ubiquiti EdgeRouter X-SFP
This patch adds support for the Ubiquiti EdgeRouter X-SFP and
improves support for the EdgeRouter X (PoE-passthrough).

Specification:
- SoC: MediaTek MT7621AT
- Flash: 256 MiB
- RAM: 265 MiB
- Ethernet: 5 x LAN (1000 Mbps)
- UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
- EdgeRouter X:
  - 1 x PoE-Passtrough (Eth4)
  - powered by Wallwart or passive PoE
- EdgeRouter X-SFP:
  - 5 x PoE-Out (24V, passive)
  - 1 x SFP (unknown status)
  - powered by Wallwart (24V)

Doesn't work:
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.

Installation

via vendor firmware:
- build an Initrd-image (> 3MiB) and upload the factory-image
- initrd can have luci-mod-failsafe
- flash final firmware via LuCI / sysupgrade on rebooted system

via TFTP:
- stop uboot into tftp-load into option "1"
- upload factory.bin image

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2017-06-07 06:33:33 +02:00
Kyson Lok
abbfcc8525 ramips: add support for GL-inet GL-MT300N-V2
This patch adds supports for the GL-inet GL-MT300N-V2.

Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)

Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 08:04:15 +02:00
Ørjan Malde
5f932988c3 ramips: add support for Asus RT-AC51U
Specification:
 - SoC: MediaTek MT7620A (580 MHz)
 - RAM: 64 MiB (Winbond W9751G6JB-25)
 - Flash: 16 MiB (Spansion S25FL128SAIF00)
 - LAN: x4 100M
 - WAN: x1 100M
 - Others: USB 2.0, reset button, wps button and 9 LEDs

Issues:
 - 5 GHz band is not functional (missing driver support)

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75;
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the sysupgrade
   image, and press upload

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin
 tftp> quit

Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
2017-05-10 08:45:12 +02:00
Alexey Belyaev
a7cbf59e0e ramips: add new device ZyXEL Keenetic as kn
This device exactly same as NBG-419N but with USB port and USB Led.

Specification:

- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0

Installation via serial console (57600 8N1) from TFTP server
 - rename the firmware to something shorter, for example
   "sysupgrade.bin" (max. 32 chars)
 - copy firmware TFTP server's directory
 - when you power on device, and see U-Boot log, immediatly push "2"
   once.
 - You will see this message:
     2: System Load Linux Kernel then write to Flash via TFTP.
        Warning!! Erase Linux in Flash then burn new one. Are you sure?
 - Push "y", and enter: device IP, then TFTP server's IP, and then
   image firmware file name.

The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).

Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-10 08:45:12 +02:00
Mathias Kresin
2ddaf96a77 ramips: add ZBT-WE826 32MB variant
The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the
device tree source file, rename the currently supported 16 MByte
version and add the 32 MByte variant.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
3cfc909c54 ramips: rename Digineo AC1200 Pro to ZBT-WG3526 32MB
The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with
unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and
add the sdhci kernel module to use it for multiple clones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
619d68bfc9 ramips: prepare ZBT-WG3526 for hardware variants
The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the
current supported 16MByte version to indicate which flash size variant
is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Jiawei Wang
ff258effd5 ramips: add support for ZBT-WE1326
Specification:
- SoC: MT7621AT, MT7603EN and MT7612EN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 512 MiB (EM6GE16EWXD-12H)
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Others: USB 2.0, micro SD slot, reset button and 8 x LEDs

Issues:
- Two LEDs for 2.4 GHz and 5 GHz Wi-Fi do not work, can't find GPIOs.
- The pwr LED is not GPIO controllable

How to install:
- The original firmware is OpenWrt, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Signed-off-by: Jiawei Wang <buaawjw@gmail.com>
2017-04-25 19:29:59 +02:00
Alexey Belyaev
3549bad814 ramips: fix ZyXEL Keenetic Omni switch config
The wan port is connected to switch port 0. Fix the mediatek,portmap as
well as the default switch config.

Signed-off-by: Alexey Belyaev <spider@spider.vc>
2017-04-25 19:29:59 +02:00
Mathias Kresin
18618695ae ramips: dont replace the board name
Use fixed led names and add each board variant instead of manipulating
the board name.

It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-21 07:47:59 +02:00
Daniel Golle
c6fe325587 ramips: rename PSG1218 to match label
Fix previous commit to be less ambigous:
PSG1218 rev.A = 5 ports, external PA, heatsinks
PSG1218 rev.B = 4 ports, internal PA, no heatsinks

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 02:55:36 +02:00
Daniel Golle
c5a7dc49d1 ramips: split Phicomm PSG1218 and PSG1218K2C
PSG1218 got only 4 Ethernet ports and WAN on port 3 while
PSG1218K2C got 5 Ethernet ports and WAN on port 4
Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while
at it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 02:29:21 +02:00
Vaclav Svoboda
6b9c25e927 ramips: fix switch port mapping for ZBT-WE2026
This patch fixes switch port mapping for Zbtlink ZBT-WE2026.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-20 08:13:56 +01:00
Vaclav Svoboda
815cc2a69a ramips: add support for Zbtlink ZBT-WE2026
This patch adds support for the Zbtlink ZBT-WE2026.

Specification:
- SoC: MediaTek MT7620N (580MHz)
- RAM: 64 MiB
- Flash: 8 MiB SPI
- LAN: 4x100M
- WAN: 1x100M

Installation through bootloader webserver:
- With the power unplugged press and hold reset button.
- Plug power and hold reset button until LED starts to blink.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-17 08:58:50 +01:00
Joseph C. Lehner
de33a4cef0 ramips: add support for Netgear EX3700
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the device's web
interface or via nmrpflash.

Co-authored-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-12 09:28:19 +01:00
Hanqing Wong
38bee61dab ramips: add support for Netgear R6220
This patch adds support for the Netgear R6220, aka Netgear AC1200 and
R6220-100NAS.

Specification:
- SoC: MediaTek MT7621ST (880 MHz)
- Falsh: 128 MiB (Macronix MX30LF1G08AA-TI)
- RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
- Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port
  on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
  (login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for
  example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot

nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.

Signed-off-by: Hanqing Wong <hquu@outlook.com>
2017-03-12 09:28:05 +01:00
Jo-Philipp Wich
2543e986ad ramips: fix Linksys RE6500 switch port mapping
Properly map the internal switch ports to the proper LAN1..LAN4 labels.

Fixes #530.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-03-07 17:39:20 +01:00
Francois Goudal
9b35815f0f ramips: add support for Afoundry EW-1200
This device features both a 2.4 and 5Ghz radio, and supports
802.11a/b/g/n/ac modes.
It has 5 Gb-Ethernet ports and a USB 3.0 host port.

It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi
chipsets, together with 128MB of RAM and 16 MB of SPI Flash.

The stock firmware is in fact based on some openwrt barrier breaker, with a
mediatek SDK kernel, and an afoundry custom made web interface (not LuCI
based).
Firmware update page on the stock web interface can not accept sysupgrade
images, it bricks the device.
At this point, the only working solution I found was to connect to the
serial console port (available on J4 header) and to use opkg to install
dropbear.
Then scp the sysupgrade file in the device's /tmp and run sysupgrade from
console without preserving configuration files.

Signed-off-by: Francois Goudal <francois@goudal.net>
2017-03-01 22:29:50 +01:00
ZengFei Zhang
edae3479e6 ramips: add support for HiWiFi HC5962
This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com

Short specification:

 - MT7621AT + MT7612EN + 7603EN
 - 256MB DDR3 RAM
 - 128MB NAND flash
 - 1+3 x 1000M Ethernet
 - 1x USB 2.0 port. 1x USB 3.0 port.
 - reset button
 - UART pad on PCB (JP3: TX, RX, GND, 3.3V)

Flash instruction:

1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin
2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/
3, use the following commands:
   $ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware
   $ mtd erase firmware_backup && reboot
After reboot you should be able to login as root via SSH on 192.168.1.1

Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
2017-02-28 23:46:02 +01:00
Wang JiaWei
d48cc5e044 ramips: add support for HiWiFi HC5661A
HC5661A is almost the same as HC5661 but MT7628AN is used instead of MT7620A.

- MT7628AN
- 128 MiB DDR2 RAM (W971GG6KB-25)
- 16 MiB SPI NOR flash (W25Q128)
- SD slot (not work yet)
- 1+4 x 100M Ethernet
- 802.11 b/g/n Wi-Fi
- 3 x LED
- 1 x button
- UART pad on PCB (JP1: TX, RX, GND, 3.3V)

The factory flash layout seems different from HC5661.
"hwf_config" is renamed to "oem" and its size changes to 0x20000.
It is modified accordingly in the dts file.

0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "hw_panic"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000160000 : "kernel"
0x000000160000-0x000000fc0000 : "rootfs"
0x000000bb0000-0x000000fc0000 : "rootfs_data"
0x000000fc0000-0x000000fe0000 : "oem"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "backup"
0x000000050000-0x000000fc0000 : "firmware"

To install LEDE, enabled the "developer mode",
which will *void your warranty* and open the SSH server at port 1022.

sysupgrade -n -F lede-ramips-mt7628-hc5661a-squashfs-sysupgrade.bin

SD slot:
- Tried to add modules kmod-sdhci kmod-sdhci-mt7620, and corresponding dts block.
- It will block WAN + 3xLAN ports, only one LAN works.
- I'm not sure why, everything else works fine.

Signed-off-by: Wang JiaWei <buaawjw@gmail.com>
2017-02-27 11:39:31 +01:00
Thibaut VARENE
157353c210 ramips: WN3000RPv3: do not setup switch
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.

Configure LAN as eth0 instead.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-14 12:19:12 +01:00
Chuanhong Guo
634328c0de ramips: correct switch configuration for Newifi D1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2017-02-13 10:24:32 +01:00
Kristian Evensen
bb7068f26c ramips: add support for Sanlinking D240
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-02-05 22:23:28 +01:00
FUKAUMI Naoki
6b0b526a4f ramips: add support for Buffalo WCR-1166DS
Buffalo WCR-1166DS is a small wireless router with

 - MT7628AN + MT7612E
 - 64MiB DDR2 SDRAM
 - 16MiB SPI flash
 - 2T2R 11ac/a/b/g/n Wi-Fi
 - 2x 10/100M ethernet switch
 - 8x programmable LED
 - 3x button
 - UART pad on PCB (J2: 3.3V, GND, TX, RX)

factory image can be installed via stock web UI.

due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2017-01-31 11:10:58 +01:00
Vitaly Chekryzhev
07a02efd07 ramips: ZyXEL Keenetic series update wan mac
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-20 00:39:30 +01:00
Vitaly Chekryzhev
f9d91a4ac7 ramips: correct keenetic-series switch index
Fix switch name typo

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-20 00:39:30 +01:00
Thibaut VARENE
7fb11c8ed2 ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-01-18 12:06:16 +01:00
BangLang Huang
2a7f669016 ramips: fix mac address of miwifi-mini
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2017-01-18 12:05:14 +01:00
Joseph C. Lehner
6b5dab9469 ramips: simplify EX2700 network config
Don't create a vlan for the Netgear EX2700's only Ethernet port.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-01-18 08:54:58 +01:00
Lazar Demin
ab90f15c89 ramips: Added Onion Omega2 and Omega2+
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>
2017-01-15 17:43:14 +01:00
Andrew Yong
3f31029b19 ramips: add support for VoCore2
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
2017-01-13 08:32:35 +01:00
Mathias Kresin
ae3ac76e56 ramips: use destinct 11AC NAS board name
Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.

To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00
Henryk Heisig
c8043137bb ramips: Add support to TP-Link Archer MR200
CPU: MT7620N 580MHz
Flash: 8MB
RAM: 64MB
build-in modem 3G/4G
four ethernet port 10/100Mbps

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-12-22 15:03:30 +01:00
Vitaly Chekryzhev
190ee7d86b ramips: add support for ZyXEL Keenetic Omni / Omni II
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2016-12-22 15:03:13 +01:00
Yong-hyu, Ban
377eac0ceb ramips: fix LAN port order of WeVO W2914NS v2
Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
2016-12-04 08:22:07 +01:00
Tobias Wolf
c2ed721e89 ramips: improve F5D8235 V1 support
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.

Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.

Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2016-12-04 07:03:17 +01:00
perillamint
68634426fe ramips: add support for WeVO W2914NS v2
Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
2016-11-21 10:13:17 +01:00
Vitaly Chekryzhev
348344874c ramips: add support for ZyXEL Keenetic Viva
Factory image can be installed via Zyxel WebUI.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-18 08:54:57 +01:00
Jasper Scholte
3d680c5728 ramips: add support for Sitecom WLR-6000
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.

The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.

The stock firmware uses the following mac addresses:

LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5:   00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)

Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:

2.4GHz: 00:0C:F6:AA:BB:D8
LAN:    00:0C:F6:AA:BB:D9
WAN:    00:0C:F6:AA:BB:DA
5 GHz:  00:0C:F6:AA:BB:DC

The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.

There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.

Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.

Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-17 06:39:52 +01:00
Dominik Menke
8b65fef173 ramips: add support for Digineo AC1200 Pro
This is basically a ZBT-WG3526 (mt7621 SoC), but with 32M flash.

Signed-off-by: Dominik Menke <dom@digineo.de>
2016-11-17 06:39:52 +01:00
Felix Fietkau
3d0e965c8b ramips: add port index in switch config for buffalo WHR-* and WSR-* devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-14 20:04:36 +01:00
Roger Pueyo Centelles
5f6e948551 ramips: Add support for Wavlink WL-WN575A3
This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug
wireless router with the following specifications:

 - CPU: MediaTek MT7628AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 2x 10/100 Mbps (switched)
 - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm
 - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm
 - Antennas: 4x external (2 per radio), non-detachable
 - LEDs: 4 programmable + LAN, WAN, POWER
 - Buttons: reset, WPS

Flashing instructions:

Factory U-boot launches a TFTP client if WPS button is pressed during power-on.
Rename the sysupgrade file and configure a TFTP as follows:

 - Client (WL-WN575A3) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2016-11-08 11:17:10 +01:00
Andrew Yong
faf94d926e ramips: add support for MikroTik hEX v3 (RB750Gr3)
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).

RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.

Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.

The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.

A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.

Signed-off-by: Andrew Yong <me@ndoo.sg>
2016-11-02 10:25:44 +01:00
YuheiOKAWA
4050cfebda ramips: add support for Planex VR500.
SOC:	MT7621A
RAM:	256MiB
NOR:	MX25L51245G

Non Wireless Router.

Issue: soft reboot problem. SPI Flash do not exit 4byte address mode.

Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
2016-10-15 11:36:51 +02:00
Mathias Kresin
51bca43f39 ramips: fix edimax 6200nl switch config
With 3a9752bbd2 and later changes to
ramips_set_preinit_iface() the default vlan config applied during
preinit was changed. These changes were made without updating the
default network config to ensure that vlan interfaces used for lan/wan
are still configured.

Fix the issue by using the default all LAN portmap and disabling not
connected switch ports using portdisable device tree parameter.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
bbdf2ac305 ramips: tag the CPU switch port
With de51026515 the explicit tagging of
the CPU port was removed. This leads to a not working default network
config, with vlans enabled but disabled CPU tagging, for boards where
all switch ports are having the same role.

In case the ports are having different roles set, tagging is is set
implicit for the CPU port by ucidef_add_switch().

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00
Mathias Kresin
b35dd9584e ramips: remove fixed lan/wan interface for switch configs
Don't set the lan/wan interface when using ucidef_add_switch. This
results into a wan interface albeit all ports a annotated as lan ports.

ucidef_add_switch takes care of setting the correct lan/wan interface
according to the annotation of the ports.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 09:01:45 +02:00