LED's were defined wrong in the device tree file, they are hardware driven because they are connected directly to the switch chip and wireless chips respectively, thus no GPIO addresses are assigned to them. It is safe to remove them from the device tree file to stop confusion.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 48055
Zero config value for default memory region means 'memory', not
not 'disabled' according to 'Control Registers Of The Coherency
Manager' manual.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47906
Since now we hopefully setup memory regions properly we no longer need this hack.
Tested and works on ubnt-erx.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47905
Only compile tested since I do not have any hardware with
devices on pcie bus.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47904
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47876
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47875
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.
The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 47844
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47843
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.
This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47842
