The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.
The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.
Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).
For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Factory image can be installed via Zyxel WebUI.
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.
The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.
The stock firmware uses the following mac addresses:
LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5: 00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)
Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
2.4GHz: 00:0C:F6:AA:BB:D8
LAN: 00:0C:F6:AA:BB:D9
WAN: 00:0C:F6:AA:BB:DA
5 GHz: 00:0C:F6:AA:BB:DC
The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.
There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.
Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Images installed via TFTP recovery or the Edimax webinterface of the
3g-6200n(l) are writting with the edimax header to flash.
Use only one image type for these boards. The migration to the
factory only images need to be done via TFTP recovery.
Use the same start address for the 3g-6200n(l) factory images as the
stock firmware images.
Thanks to Jan Dostrasil for reporting all the issues of the 3g-6200nl
and the patient testing of all changes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files
Signed-off-by: Klaus <k-laus@quantentunnel.de>
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet
Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
kmod-rt2x00-lib and kmod-mac80211 need to be removed, as they depend on
kmod-cfg80211. kmod-rt2800-pci should not be installed anyways.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The D-Link DIR-860L B1 has a flash chip which doesn't support
4K sectors. Since the DIR-860L B1 was the only mt7621 board which had
the 4k blocksize set, the 4K sector support is removed from the kernel
config.
I've checked the flash chips of all boards having set a 4K blocksize
again. This time I searched harder to finding bootlogs instead of
relying on wikis articles and/or the device tree source file.
The Planex MZK-DP150N has an en25q32b instead of the mentioned one in
the dts. Albeit the en25q32b supports 4K sectors, 4K support is not
enabled in the driver. Change the blocksize for this board back to 64K.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that all seama images are using the new build code this seama recipe
used with the old build code can be dropped.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.
Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.
The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.
For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:
- Ralink V11ST-FE
- Ralink AP-RT3052-V22RW-2X2
- MediaTek MT7628 EVB
- MediaTek MT7621 EVB
- UPVEL UR-326N4G
- Buffalo WZR-AGL300NH
Signed-off-by: Mathias Kresin <dev@kresin.me>
The image generation for TEW-691GR and TEW-692GR was broken since
79d02229 due to the move of the UMedia recipe to another Makefile.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Thunder Timecloud is a small NAS with MT7621A. It has 1 USB port and an
SD Card slot. There is no wireless cards.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash,
3.5mm audio out support. but no ethernet and usb ports.
so you must default enable wifi.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The NixCore X1 is a Ralink/MediaTek rt5350 WiFi Module.
http://nixcores.com/
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Drew Gaylo <drew@nixcores.com>
Pinmux for rgmii needs to be set to rgmii, not gpio.
Hide the ESW switch on boot (using new rgmii esw devicetree attribute).
Also add a Sitecom-specific profile, since the image needs to include
the rtl8366 kernel driver.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has
64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with
802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac
MT7612E-based 5 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.
Signed-off-by: Michael Lee <igvtee@gmail.com>
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.
Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
add support for Planex MZK-EX750NP.
MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49268
CS-QR10 is MT7620A based IP Camera.
the camera and sound does not work with kernel 4.4.
- camera chip is sn9c291.
- sound chip is wm8960.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49234
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.
v1->v2:
* Remove some references to 2626 that I had missed in the dts.
v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 49213
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.
it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
SVN-Revision: 49211
Currently the maximum image size defaults to 8Mbyte even though this model has 16Mbyte of flash memory.
Tested and works on my device.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49129
- all subtarget specific defines are in their own files
- common defines left in main Makefile
- each subtarget makefile idefed with SUBTARGET
- all subtargets compile tested
- few seems to be broken/unneeded things marked with FIXME
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49104
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.
The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.
Fix the assembly code to reserve stack space for the
registers to avoid that.
Untested. It seems that the lzma-loader is not used at all?
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49062
1) Use leds to indicate:
Red - Power
Amber - Radio On
Blue - Wifi associated
2) Add profile to default build group for MT7628 subtarget
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
SVN-Revision: 49045
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.
SVN-Revision: 48994
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.
SVN-Revision: 48993
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.
SVN-Revision: 48992
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 48968
This patch adds profiles and support for building factory and
sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48906
This patch adds support for building factory and sysupgrade images
for the Netgear EX2700 that don't require modification of u-boot
environment variables.
The bootloader on this device expects the kernel partition to end
on a 64k block boundary. The last 64 byte of the kernel partition
must contain a valid uImage header - in the stock firmware, this is
the uImage header of the root filesystem. For this patch, we're using
the uImage header of a 0 byte partition (ex2700-fakeroot.uImage).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48771
