Fix incorrect offset and size of linux partition.
Fixes: 97b36aca09 ("brcm63xx: add pflash for remaining pflash equipped boards")
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The warning will be triggered by jffs2 or UBI, and partial writes are no
issue for most flash chips.
Fixes: 2a2b16210b ("brcm63xx: backport upstream solution for SPI message size limits")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz)
Flash size: 32MB (split 16/16 dual boot)
RAM size: 64MB
Wireless: BCM432x 802.11a/b/g/n(pci)
Ethernet: Broadcom BCM53115
USB: 1 x USB 2.0
Known issues:
- Unable to detect 53115 switch attached to MDIO. Not supported
- No support for the cable port
More info on the device and the research can be found at:
http://www.actiontec.com/212.html
Same FCC ID as:
https://wikidevi.com/wiki/Actiontec_V1000H_(Telus)
Signed-off-by: Anthony Sepa <anthonysepa@yahoo.ca>
[jonas.gorski: fix commit subject/message]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The pinmux register is at relative offset 0x8, not 0xc. Fixes hang
when trying to modify pins >= 32.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Instead of bit banging SPI to talk to the GPIO chip, use the hardware
led controllers intended for controlling the LEDs.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Now that we always provide these partitions through DT, we don't need to
pass their data through parser data from board files anymore.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Allow the parser to be invoked from DT without fixed cfe/linux/nvram
partitions. This allows flash to be probed from DT also for multi
flash-size images.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Build profile for Asmax AR 1004g refers to an invalid DTS "rg100a". The
correct DTS for this device is "ar1004g".
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Add SPROM wifi to the kernel board data.
After this fix, the wifi won't work anyway due the lack
of RAM memory (16 MB). It will throw a kernel panic
when loading the b43 drivers.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Fix the register for configuring rising/falling edge
Rising should be sense=1, and falling sense=0.
The old driver used these values, but the new one have
them flipped.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Add support for the Observa Telecom VH4032N router.
This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB
host ports.
The wifi chip is an onboard Broadcom BCM43222.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: use gpio-hog instead of abusing ephy-reset]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Probe the switch through DT instead of a platform device. This fixes
probe, as GPIO offsets are now properly accounted for.
Fixes the following issue:
[ 0.802953] 8021q: 802.1Q VLAN Support v1.8
[ 0.810518] rtl8366_smi: gpio_request failed for 18, err=-517
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
BCM6362 and BCM3380 seem to share the same PRID. Disable serial output
for them until we can find a way to tell them apart reliably.
Fixes: 8f3cfe4ba2 ("brcm63xx: lzma-loader: add BCM3380 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This patch adds support for the ADB P.DG AV4202N aka Pirelli PRG AV4202N.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Add support for mapping some GPIO lines to IRQs. GPIO to IRQ mappings
were found out through experimentation, helped by having the GPIO as
output still toggling the IRQ input.
Based-on: http://patchwork.ozlabs.org/patch/660534/
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Setting the clear bit for an interrupt seems to cause interrupts to be
deasserted again immediately. So unset the bit for BCM6318 to allow
subsequent interrupts to still work.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
In order to prepare support for generating tagged switch configurations by
default, explicitely request untagged configs for boards which do not already
request tagging to retain default behaviour.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This flag was added to 4.9 with upstream commit
76a4707de5e18dc32d9cb4e990686140c5664a15.
Signed-off-by: Victor Shyba <victor1984@riseup.net>
[refresh and adjust platform patches, fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The imagetag RSA signature field may not exceed 20 characters, so trim the
Git hash portion from the REVISION variable in order to ensure that the
resulting string fits within this field.
The current revision values may be longer than 20 chars, especially when
building within a dirty tree. In this case, the revision will look like
"r2435+75-b4aa3c8" which, combined with the "LEDE-" prefix, is 21 chars long.
Fixes the following error spotted by the buildbots:
Error: RSA Signature (rsa_signature,r) too long.
make[4]: *** [.../lede-brcm63xx-generic-NEUFBOX6-squashfs-cfe.bin] Error 1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix configuration files for the Livebox 1 routers.
- Add status led
- Set eth0 as the LAN port, for coherence with RedBoot and comfortability.
- Add led triggers
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix Image generation for the Livebox 1
- missing "relocate-kernel", wrong "LOADADDR", fix it
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- part probe wrong, it should be RedBoot (uppercase matters)
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- leds are totally wrong, fix them.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
