Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the .dtsi
file. Most probably it went into openwrt here:
https://dev.openwrt.org/browser/trunk/target/linux/ipq806x/patches-3.18/101-ARM-qcom-add-USB-nodes-to-ipq806x-ap148.patch?rev=45261
copied from Qualcomms attempt here: https://lkml.org/lkml/2015/11/20/116
Now unloading and repeated module loading is working just fine,
no matter if you'd remove dwc3-of-simple or dwc3.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Allow module unloading by fixing a mistake.
qcom_dwc3_phy_write_readback() is expecting (phy, offset, mask, value)
while the mistake was calling it with (phy, offset, value, mask)
The patch is swapping value and mask.
Without the patch unloading the dwc3 module was showing a
write to QSCRATCH failed and repeated module loading was
failing:
root@LEDE:/# rmmod dwc3
[ 19.167998] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.168084] usb usb4: USB disconnect, device number 1
[ 19.173371] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 19.177134] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 19.182960] usb usb3: USB disconnect, device number 1
[ 19.189023] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 19.192989] qcom-dwc3-usb-phy 110f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
[ 19.199064] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.205912] usb usb2: USB disconnect, device number 1
[ 19.211611] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 19.215905] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 19.221751] usb usb1: USB disconnect, device number 1
[ 19.227307] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 19.231795] qcom-dwc3-usb-phy 100f8830.phy: write: 8000000 to QSCRATCH: 0 FAILED
root@LEDE:/# modprobe dwc3
[ 29.583343] phy phy-100f8830.phy.4: phy init failed --> -110
[ 29.583399] dwc3 10000000.dwc3: failed to initialize core
[ 29.588169] dwc3: probe of 10000000.dwc3 failed with error -110
[ 29.652943] phy phy-110f8830.phy.2: phy init failed --> -110
[ 29.652988] dwc3 11000000.dwc3: failed to initialize core
[ 29.657735] dwc3: probe of 11000000.dwc3 failed with error -110
root@LEDE:/#
With patch repeated module unloading and loading is working good:
root@LEDE:/# rmmod dwc3
[ 22.622214] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.622298] usb usb4: USB disconnect, device number 1
[ 22.627401] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 22.631492] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 22.637054] usb usb3: USB disconnect, device number 1
[ 22.643721] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 22.647421] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.652910] usb usb2: USB disconnect, device number 1
[ 22.659219] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 22.662768] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 22.668604] usb usb1: USB disconnect, device number 1
[ 22.674803] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# modprobe dwc3
[ 25.404592] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.404694] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 25.409444] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.416589] xhci-hcd xhci-hcd.0.auto: irq 168, io mem 0x10000000
[ 25.426509] hub 1-0:1.0: USB hub found
[ 25.431626] hub 1-0:1.0: 1 port detected
[ 25.435472] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 25.439206] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 25.444573] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.452926] hub 2-0:1.0: USB hub found
[ 25.460420] hub 2-0:1.0: 1 port detected
[ 25.525037] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.525099] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[ 25.529750] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x00010010
[ 25.537002] xhci-hcd xhci-hcd.1.auto: irq 169, io mem 0x11000000
[ 25.546583] hub 3-0:1.0: USB hub found
[ 25.551997] hub 3-0:1.0: 1 port detected
[ 25.555734] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 25.559621] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[ 25.564942] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 25.573063] hub 4-0:1.0: USB hub found
[ 25.580842] hub 4-0:1.0: 1 port detected
root@LEDE:/#
Fixes: dwc3 module unloading
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Many (most?) devices can't boot raw kernel using tftp and probably none
allows flashing it. It's way more usable to have TRX with kernel
containing initrams as such an image can be actually flashed.
An exception are Buffalo devices which have recovery mode with support
for booting kernels over TFTP. For them keep building default images.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Makes use of the syscon tcsr and enables both USB ports. Cleans up
qcom-ipq8064.dtsi from previous attempts.
Fixes FS#497
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Current driver shows temp in full degrees while other apps await it
to be in millidegrees.
Initially the driver represents termal data in millidegrees but then
it gets divided by TSENS_FACTOR. So lets just set it to '1'.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Deactivate all the ARM64 erratums by default. The target code should
activate them if needed. This fixes a problem with a new erratum added
in kernel 4.9.17 breaking brcm2708.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This gets us in sync with dts from kernel 4.11. Two patches were already
backported earlier.
I decided to use 03x prefix as it's kind of similar to the 3xx prefix:
3xx - architecture specific patches
It isn't any documented or strict rule though. We don't need to stick to
it if we hit any problems.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
modify 0152-lantiq-VPE.patch from
commit e0229a16b0 ("lantiq: added support for VPE1")
- remove wdog function declarations from header (asm/vpe.h)
- remove wdog command line init functions (vpe.c)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
- remove patched header (vpe.h) because kernel
already provides one (asm/vpe.h)
- remove module softdog_vpe since watchdog functionality is unused
- remove module softdog_vpe from Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Even the commit message of the patch adding support for the MiWiFi Nano
says that a 16 MB flash chip is used. Extend the firmware partition to
make use of all available flash space.
Fixes: FS#622
Signed-off-by: Mathias Kresin <dev@kresin.me>
Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Commit 23dac14d058f ("MIPS: PCI: Use struct list_head lists") changed
the controller list from reverse to straight order. Use the last entry
in the controller list to get the fist conroller of the system.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Upstream commit 23dac14d058f ("MIPS: PCI: Use struct list_head lists")
changed the controller list from reverse to straight order without
taking care of the changed order for the scan of the recorded PCI
controllers.
Traverse the list in reverse order to restore the former behaviour.
This patches fixes the following PCI error on lantiq:
pci 0000:01:00.0: BAR 0: error updating (0x1c000004 != 0x000000)
Signed-off-by: Mathias Kresin <dev@kresin.me>
Right now all brcm2708 patches are extracted from the non-mainline
raspberrypi/linux git tree. Many of them are hacks and/or are unneeded
in LEDE. Raspberry Pi is getting better and better mainline support so
it would be nice to finally start maintaining patches in a cleaner way:
1) Backport patches accepted in upstream tree
2) Start using upstream drivers
3) Pick only these patches that are needed for more complete support
Handling above tasks requires grouping patches - ideally using the same
prefixes as generic ones. It means we should rename existing patches to
use some high prefix. This will allow e.g. use 0xx for backported code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also
labeled as R602F, R602, etc.) is a simple N300 router with 5-port
10/100 Mbps switch, non-detachable antennas and USB.
CPE505 is an outdoor CPE with PoE support and detachable antennas.
Both devices are based on Qualcomm/Atheros QCA9531 v2.
Common specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- UART (J2) header on PCB
R602N specification:
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm
- 2x external, non-detachable antennas
- 7x LED, 1x button
CPE505N specification:
- 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V)
- 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm
- 2x external, detachable antennas (RP-SMA connectors)
- 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button
Flash instructions:
It seems that there are many different versions of the firmware which
these devices are shipped with. The generic/standard one is based on
some modified OpenWrt and LEDE firmware can be flashed directly from
vendor's webgui or with sysupgrade (root password is "admin123").
Before flashing, make sure (use "fw_printenv") that the kernel load
address in your device is set to "0x9f050000" (bootcmd variable is
"bootm 0x9f050000"). If your device uses different load address, you
should first change it, under vendor's firmware, with command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
Where OLD_ADDRESS is previous kernel load address (in CPE505 version
I got access to, it was "0x9fe80000"). This will allow you to use
both the vendor's and LEDE firmware.
If version of your device contains empty U-Boot environment (you will
get information about this after issuing "fw_printenv"), you should
use U-Boot, serial line access and TFTP to perform firmware upgrade:
1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS"
5. saveenv && reset
These devices contain also web recovery mode inside U-Boot. It can be
started with pressing the reset button for around 3 seconds just after
the device powerup. Web recovery panel is available on "192.168.10.9"
and to be able to use it, IP on your PC must be set to "192.168.10.10".
Make sure to change kernel load address before using recovery mode or
the U-Boot will not be able to load LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This patch adds initial support for the MikroTik RouterBOARD hAP ac
(RB962UiGS-5HacT2HnT).
All functions are supported except:
-SFP cage (eth1) is not working
-WLAN LEDs are not working
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This patch adds support for the MikroTik RouterBOARD hAP ac lite
(RB952Ui-5ac2nD).
The hAP ac lite is nearly identical to the hAP, with an added QCA9887
5GHz radio. The 2.4GHz radio ID is also changed in the hAP ac lite.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
v4.9 CM code has a few bugs on this HW. Disable the GCR register access
during boot. This caused a cpu stall.
Signed-off-by: John Crispin <john@phrozen.org>
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
This adds kernel support for the Pistachio SoC and the Marduk (Ci40)
board which uses it.
Much of the code for Pistachio has been upstreamed however some
patches are still required to boot from the Marduk board:
* spi bug fixes
* dma bug fixes
* pistachio internal clock tree bug fixes
* spi-nand implementation
* dts based mtd device naming scheme
* dts backports and bug fixes
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
This patch adds support for AVM FRITZ!Box 4040.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
Not planned:
- WAN<->LAN short-cut
- Qualcomm Secure Execution Environment
- ...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
This adds support for describing GPIO chips placed on PCIe cards. Thanks
to this we get working 2.4 GHz LED on Tenda AC9.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is the standard way we handle this. Please note (it seems) I could
drop few symbols as they are hidden under (disabled) DRM_LEGACY now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add back support for the independent_clocks definition that has been
removed between kernel 4.4 and 4.9 by upstream commits
eb96924acddc709db58221c210ca05cd9effb1df and
e86eee6bc2aaa6b3637f6497b26beee09a91bde9
* extend the new cpufreq_dt_platform_data definition in cpufreq-dt.h
* revert the removal of its usage in cpufreq-dt.c
* use new cpufreq-dt.h in qcom-cpufreq.c
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
For IPQ806x targets, TZ protects the registers that are used to
configure the routing of interrupts to a target processor.
To resolve this, this patch uses scm call to route GPIO interrupts
to application processor. Also the scm call interface is changed.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
At the moment as a workaround definition for scm firmware in DT is used as if it is
apq8064 board. This leads to incomplete scm firmware initialization and as a result
cpuidle driver fails to configure.
By design unlike other qcom boards ipq do not use clocks to connect to scm.
Considering this we're removing from DT and scm driver clocks for ipq boards.
As a result cpuidle does not produce errors about failed configuration anymore.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
This fixes GIC interrupts (required before switching to 4.9), adds few
new entires & introduces DTS for Archer C5.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This patch adds support for the Zbtlink ZBT-WE2026.
Specification:
- SoC: MediaTek MT7620N (580MHz)
- RAM: 64 MiB
- Flash: 8 MiB SPI
- LAN: 4x100M
- WAN: 1x100M
Installation through bootloader webserver:
- With the power unplugged press and hold reset button.
- Plug power and hold reset button until LED starts to blink.
- Install sysupgrade image using web interface on 192.168.1.1.
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
SMP state is generally affected by
- CONFIG_SMP build-time kernel configuration option and
- 'nosmp' runtime kernel commandline option
The SMP state within vpe-mt.c is determined by CONFIG_SMP option.
A runtime check is needed if VPE functionality
should be used with a kernel image that supports SMP.
This fix introduces a check for 'nosmp' command line option
if CONFIG_SMP kernel configuration option is enabled.
Note: This patch is needed to use lantiq FXS if CONFIG_MIPS_MT_SMP
(that activates CONFIG_SMP) is enabled within kernel configuration
and the 'nosmp' command line argument is given to disable SMP at runtime.
Without this patch CONFIG_MIPS_MT_SMP must be disabled before using FXS.
With this patch setting the 'nosmp' parameter is enough.
In general, concurrent usage of FXS and SMP
is incompatible and will cause kernel panics.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
It is not needed for anything on the system and skipping this saves some
build time, especially in cases where there is nothing to do.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The problem is caused by the incorrect handling of the parent inode's
i_nlink count for the dentry to be RENAME_EXCHANGED. There are 3 cases
to consider. Assume we want to RENAME_EXCHANGE struct dentry *a and
struct dentry *b, and inode_a is pointed to by dentry_a, inode_b is
pointed to by dentry_b:
1. If inode_a is a directory, but inode_b isn't, then we must decrease
the i_nlink count of old_dir_i, and increase the i_nlink of new_dir_i.
2. If inode_a isn't a directory, but inode_b is a directory, then we
must increase the i_nlink of old_dir_i, and decrease the i_nlink count
of new_dir_i.
3. If the types of inode_a and inode_b are the same, we don't change the
i_nlink for either old_dir_i or new_dir_i.
Signed-off-by: Jing Qiu <aqiu0720@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Switch to the common LED related status_led_blink_* functions in
set_state() as it's done in most of other targets.
Also, use "status_led_on" instead of "status_led_set_heartbeat"
and incorrect "status_led_set_on" in the "done" state.
Moreover, remove outdated comment from the script.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
When the device name doesn't already contain "RouterBOARD", this patch adds
this string to the machine name.
Most NOR devices already have "RouterBOARD" in their hardware-stored device name,
but not all of them.
This patch also makes the code more robust against buffer overflows.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This driver supports CPU-specific idle features on recent Intel
processors. It does not conflict with the ACPI idle driver and
that driver will continue to be used for unsupported and non-Intel
processors.
Signed-off-by: Michael Marley <michael@michaelmarley.com>
The x86_64 build already has the k10temp driver for AMD processors
built in, so this patch adds the coretemp driver for the same
functionality on Intel processors.
Signed-off-by: Michael Marley <michael@michaelmarley.com>
SMP state is generally affected by
- CONFIG_SMP build-time kernel configuration option and
- 'nosmp' runtime kernel commandline option
The SMP state within vpe-mt.c is determined by CONFIG_SMP option.
A runtime check is needed if VPE functionality
should be used with a kernel image that supports SMP.
This fix introduces a check for 'nosmp' command line option
if CONFIG_SMP kernel configuration option is enabled.
Note: This patch is needed to use lantiq FXS if CONFIG_MIPS_MT_SMP
(that activates CONFIG_SMP) is enabled within kernel configuration
and the 'nosmp' command line argument is given to disable SMP at runtime.
Without this patch CONFIG_MIPS_MT_SMP must be disabled before using FXS.
With this patch setting the 'nosmp' parameter is enough.
In general, concurrent usage of FXS and SMP
is incompatible and will cause kernel panics.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
The available amount of coherent DMA memory is very limited. On Linux
4.4 this issue was worked around by increasing the pool size.
It turns out that using coherent memory here is completely unnecessary.
This change reworks the driver code to use kzalloc+dma_map_single
instead.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not patch upstream files, overwrite them entirely. The upstream files
are buggy for a number of devices and this significantly simplifies the
patch structure
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: John Crispin <john@phrozen.org>
The Netgear WNDR4300, equipped with an Atheros AR8327 Gigabit Switch,
has two LEDs on each port for monitoring LAN activity, but it currently
only uses one. Fix the configuration to use both.
The patch provides this new configuration:
- green LED: 1 Gbps link, 4Hz blink frequency
- amber LED: 10/100 Mbps link. 4Hz for 100Mbps, 2Hz for 10Mbps
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
At now there is no general rule about what part of (or whole) machine
name string should be used for board name assignment/detection and every
target handles this in a different way.
For most of the boards in ar71xx we already use only part of the string,
generally without the vendor name.
This shortens wildcards patterns in case statement for board name
assignment, wherever possible (e.g. where it won't be misleading).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Be consistent and always use double quotes for case statement patterns,
as in other targets. With this approach it should be less confusing for
users adding support for new devices.
Also, be consistent with MikroTik boards wildcard pattern.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
It's unused since commit 7427007193 ("x86: remove the olpc subtarget,
it has been unmaintained for a long time").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The MV88E6176 switch is present on the GW16083 and the GW5904
As of a5c32a1f19 these drivers are to be
enabled static in per-target kernels.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
If a 'fixfdt' uboot script exists, execute it prior to bootm to allow
easy bootloader env based fdt fixups and tweaks
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Fix a kernel crash caused when CONFIG_FIXED_PHY used for fixed phy drivers
in phy-add-aneg-done-function patch.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The -factory images can be flashed from the device's web
interface or via nmrpflash.
Co-authored-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
This patch adds support for the Netgear R6220, aka Netgear AC1200 and
R6220-100NAS.
Specification:
- SoC: MediaTek MT7621ST (880 MHz)
- Falsh: 128 MiB (Macronix MX30LF1G08AA-TI)
- RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
- Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600
Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port
on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
(login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for
example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot
nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.
Signed-off-by: Hanqing Wong <hquu@outlook.com>
The port is labeled as wan and was only used as lan port because of the
"tx ring full" issues fixed with 8f02f7c.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Using the lantiq,wan device tree property for one interface node and
the lantiq,switch device tree property for another interface node at
the same time was never intended/isn't supported at the moment.
The property is meant to be used in two phy operation mode where one
phy is assigned to an interface without lantiq,* device tree property
and the other phy is assigned to an interface with the lantiq,wan
device property to have two netdevs.
If both properties are used at the same time, the lantiq,wan interface
is shown as independent netdev but not able to operate independent. The
port needs to be managed via swconfig. These dependency is not obvious
and fooled already a lot of users.
Add a default WAN vlan for xrx200 devices having an ethernet WAN port
and remove the lantiq,wan device tree property. Leave it up to the user
to set the ethernet WAN port as default WAN interface or to use this
port as additional LAN port.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The two phy operation mode where one phy is assigned to an interface
without lantiq,* device tree property and the other phy is assigned to
an interface with the lantiq,wan device property was broken with the
multicast package leaks between vlans fixes.
Move the multicast packages relevant portmap settings to the condition
which handles multicast packages for better readability.
Replace the priv->port_map based port_map only for the interface which
has the lantiq,switch device tree property set, to allow tagged
multicast packages in two phy mode where the lantiq,switch device tree
property isn't used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
* The left most mini-PCIe slot (the one attached to SIM2) can be
power-cycled by setting GPIO 0 to high/low.
* The D240 only needs the MT76x2 module, so update makefile to reflect this.
Note that until the default mt7620 target is updated, then kmod-mt76 (and thus
kmod-mt7603) will be selected by default.
v2->v3:
* Indentation error.
v1->v2:
* Rename gpio and remove redundant comment (thanks Piotr Dymacz)
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
mtk-mmc/mtk_sd.ko only depends on mmc_core and mmc_block.
And, we remove kmod-sdhci dependence assignment from all related target devices.
Signed-off-by: Furong Xu <xfr@outlook.com>
Change dts file to add default sata trigger to sata led.
Backport upstream accepted patch to add sata trigger to device tree
source files already upstreamed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[backport upstream accepted patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ASL56026 is a VDSL2 router with dual 100mbit ethernet,
also known as the ECI B-FOCuS V-2FUb/I.
CPU: Lantiq XRX268 v1.1 at 333MHz
Modem: Lantiq VRX208
RAM: 32MiB DDR2 at 167MHz
Flash: 8MiB NOR, Spansion S29GL064N90TF04
UART is at JP1:
Pin 1 TX
Pin 2 GND
Pin 3 +3.3V
Pin 4 NC
Pin 5 RX
Boot selection pins are exposed via several resistor jumpers:
boot_sel0 is at J15, on the rear of the board. Default is high.
boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low.
boot_sel2 is at J12, directly below the SoC. Default is low.
boot_sel3 is at J16, on the rear of the board. Default is low.
The boot_sel pins should never be shorted, the jumper must be moved or
a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work)
To install with the stock bootloader you must break the built in image selection process
which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion
This is done by setting loadaddr and both f_upgrade_addr vars to the same address:
VR9 # setenv loadaddr 0xB0040000
VR9 # setenv f_upgrade_addr 0xB0040000
VR9 # setenv f_upgrade2_addr 0xB0040000
VR9 # saveenv
Then flash the firmware image:
VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin
VR9 # erase B0040000 +${filesize}
VR9 # cp.b 0x81000000 0xB0040000 ${filesize}
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
This backports fixes for setting of_node and making it possible to read
extra info from DT. This was partially fixed by:
[PATCH] leds: leds-gpio: Set of_node for created LED devices
but it didn't work during initialization.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Open-code usb_phy_generic_register instead of calling it, since it is
really trivial. Avoid pulling CONFIG_NOP_USB_XCEIV into the kernel
config and add a proper dependency instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The malta "be" and "le" subtargets share the arch with many devices of
ar71xx and ramips. They can be handy for testing, debugging, trying
both snapshot and release builds.
This commit makes the "be" subtarget part of the ci and release builds
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
As usual these patches were extracted and rebased from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.9.y
- Remove led1 from diag.sh for RPi3 since it causes boot issues.
- Fix modules.mk typos.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Bump kernel from 4.4.50 to 4.4.52
Refresh patches
Compile tested all 4.4. targets
Run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
These modules are not needed by the EX2700, since it does not
have an external wifi chip (MT7620A is covered by rt2x00).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
This device features both a 2.4 and 5Ghz radio, and supports
802.11a/b/g/n/ac modes.
It has 5 Gb-Ethernet ports and a USB 3.0 host port.
It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi
chipsets, together with 128MB of RAM and 16 MB of SPI Flash.
The stock firmware is in fact based on some openwrt barrier breaker, with a
mediatek SDK kernel, and an afoundry custom made web interface (not LuCI
based).
Firmware update page on the stock web interface can not accept sysupgrade
images, it bricks the device.
At this point, the only working solution I found was to connect to the
serial console port (available on J4 header) and to use opkg to install
dropbear.
Then scp the sysupgrade file in the device's /tmp and run sysupgrade from
console without preserving configuration files.
Signed-off-by: Francois Goudal <francois@goudal.net>
Somewhere between 4.4 and 4.9 there was a change that made
OF_EARLYCON_DECLARE adding entries to the __earlycon_table instead of
__earlycon_of_table. We need to keep this table as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This driver has been added instead of improving spi-bcm53xx. It has some
advantages: allows SPI speed control & hopefully doesn't have bug that
was stopping us from using multiple SPI messages for writing flash data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
the mtd_get_mac_ascii function called within this script requires the inclusion of /lib/functions/system.sh
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com
Short specification:
- MT7621AT + MT7612EN + 7603EN
- 256MB DDR3 RAM
- 128MB NAND flash
- 1+3 x 1000M Ethernet
- 1x USB 2.0 port. 1x USB 3.0 port.
- reset button
- UART pad on PCB (JP3: TX, RX, GND, 3.3V)
Flash instruction:
1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin
2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/
3, use the following commands:
$ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware
$ mtd erase firmware_backup && reboot
After reboot you should be able to login as root via SSH on 192.168.1.1
Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
Fixes the following build error:
CC arch/mips/boot/compressed/decompress.o
OBJCOPY arch/mips/boot/compressed/vmlinux.bin
XZKERN arch/mips/boot/compressed/vmlinux.bin.z
OBJCOPY arch/mips/boot/compressed/piggy.o
LD vmlinuz
arch/mips/boot/compressed/decompress.o: In function `lzma2_lzma':
/tmp2/mehrtens/linux/arch/mips/boot/compressed/../../../../lib/xz/xz_dec_lzma2.c:884: undefined reference to `memmove'
make[1]: *** [vmlinuz] Error 1
make: *** [vmlinuz] Error 2
lib/decompress_unxz.c only defines its own memmove function if there is no
macro with the same name.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SPROM wifi to the kernel board data.
After this fix, the wifi won't work anyway due the lack
of RAM memory (16 MB). It will throw a kernel panic
when loading the b43 drivers.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Fix the register for configuring rising/falling edge
Rising should be sense=1, and falling sense=0.
The old driver used these values, but the new one have
them flipped.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
HC5661A is almost the same as HC5661 but MT7628AN is used instead of MT7620A.
- MT7628AN
- 128 MiB DDR2 RAM (W971GG6KB-25)
- 16 MiB SPI NOR flash (W25Q128)
- SD slot (not work yet)
- 1+4 x 100M Ethernet
- 802.11 b/g/n Wi-Fi
- 3 x LED
- 1 x button
- UART pad on PCB (JP1: TX, RX, GND, 3.3V)
The factory flash layout seems different from HC5661.
"hwf_config" is renamed to "oem" and its size changes to 0x20000.
It is modified accordingly in the dts file.
0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "hw_panic"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000160000 : "kernel"
0x000000160000-0x000000fc0000 : "rootfs"
0x000000bb0000-0x000000fc0000 : "rootfs_data"
0x000000fc0000-0x000000fe0000 : "oem"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "backup"
0x000000050000-0x000000fc0000 : "firmware"
To install LEDE, enabled the "developer mode",
which will *void your warranty* and open the SSH server at port 1022.
sysupgrade -n -F lede-ramips-mt7628-hc5661a-squashfs-sysupgrade.bin
SD slot:
- Tried to add modules kmod-sdhci kmod-sdhci-mt7620, and corresponding dts block.
- It will block WAN + 3xLAN ports, only one LAN works.
- I'm not sure why, everything else works fine.
Signed-off-by: Wang JiaWei <buaawjw@gmail.com>
The following will enable the TPM kernel module, as well as support for
the atmel i2c TPM driver. Tested and confirmed working on an Aerohive
AP-121
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The more straight forward approach for generating the pure and unpadded
kernel file which then can be used for initramfs straight.
Build options for factory.img and sysupgrade.tar are handeled
seperately.
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
On Mikrotik SPI NOR devices, the firmware partition must be erased when flashing
from stock firmware, otherwise leftover bits (in particular a kernel signature)
can trigger a boot loop.
When booted from initramfs (the only way to flash LEDE on these devices),
this patch unconditionally erases the firmware partition in the pre_upgrade()
stage for all supported SPI NOR devices.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch frees up flash space on the EX2700, by
removing unused mt76 drivers and firmware.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
Backport kernel patches for LS1043A Rev1.1 support from upstream,
patchwork, and SDK. And update to latest u-boot to support LS1043A
Rev1.1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The ethernet driver uses a port map override via special tag to control
the ports on which multicast packets are sent. This was added to work
around an issue in the switch that was occasionally leaking packets onto
the wrong vlan.
Unfortunately the change had some leftover lines that were overwrting
the port map with a list of all ports, thus always leaking packets onto
the wront vlan.
Fix this by only enabling the override with the VLAN port map and only
if a matching VLAN port map was actually found
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bump kernel from 4.4.49 to 4.4.50
Compile tested: All targets
Run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
This patch enables mtdsplit for the MikroTik subtarget.
It converts mach-rbspi.c to use a single "firmware" partition.
Finally, it converts the SPI NOR profile to metadata images:
the original combined-image format is gone, the images are now
"standard" sysupgrade images with metadata appended.
Note: kernel2minor apparently pads the kernel container to erase-block
boundary, but this is undocumented behaviour, so we do not rely on it
and call pad-to anyway.
Note: in platform.sh, the boards are tested last in platform_check_image()
as this should eventually become the "*)" default case when more devices
switch to metadata images.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The RouterBOOT bootloader does not care where the kernel lives in the SPI
flash, all that matters is that the kernel is wrapped in the custom yaffs
container as generated by kernel2minor.
This container has a fixed signature as follows:
00000000 00 00 00 01 00 00 00 01 ff ff 6b 65 72 6e 65 6c |..........kernel|
This patch adds mtdsplit support for identifying that signature and
triggering the search for the rootfs. rootfs is expected at EB boundary since
we use wget mtd_find_rootfs_from(). We make no use of the yaffs file size
field because it contains invalid data in the image generated by kernel2minor.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The fakeroot header is expected by the netgear bootloader in the last
64 bytes of the last block used by the uImage. With the current
linux-4.9 uImage being more than 128k smaller than the linux-4.4 uImage
the bootloader was unable to locate the rootfs ih_magic and was
refusing to load and start the kernel.
Fixes: FS#542
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
CONFIG_FB_EFI and CONFIG_FB_SIMPLE are needed to display console text on
EFI framebuffer.
CONFIG_FB_EFI is needed when the kernel is directly launched via EFI
shell or EFI startup.nsh script.
CONFIG_FB_SIMPLE is needed when launching the kernel via grub2 efi. In
this case, grub2 has prepared a gfxterm framebuffer and the kernel just
need to use the already prepared grub's gfxterm framebuffer to display
console text.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
For AR71XX devices, GMAC1 always connects port 0 of the built-in switch,
as the CPU port.
This patch sets correct vlan for some devices with wrong settings:
a) mark port 0 as CPU port, tagged
b) reverse port order, marking these ports untagged
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for the TP-Link TL-WR802N Version 2.
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
Properly resolve symbolic tag names when constructing the base feed Git url
and avoid emitting "HEAD" references when building from detached commits.
Fixes#495, #501.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes the following warning on first boot if the ltq_atm modules are
not included in the image:
ls: /lib/modules/4.4.49/ltq_atm*: No such file or directory
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the nas0 interface for the netdev trigger as default. Use the ptm0
interface for xRX200 boards to match the default wan interface set in
02_network.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move the code to check if the current system is a system with vdsl
support to a dedicate function to make it reusable.
Signed-off-by: Mathias Kresin <dev@kresin.me>
QCA956x is configured like AR934x, not like the older chips.
Should fix ethernet hangs when using the WAN port without SGMII
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This makes the Geode images actually useful again. The Geos profile
should include the relevant hardware for that board, and the Default
profile adds the via-rhine adapter which seems to have been present in
the net5501 and alix targets killed in commit 9e0759ea26 ("x86: merge
all geode based subtargets into one").
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO
Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery
Tested on:
- Lima development kit
Signed-off-by: Karol Dudek <karoiz@sli.pl>
