This will allow simple sysupgrade-s including simpler reverting to the
original firmware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43799
After the changes make ubinize.cfg optional in image.mk, ubifs
generation can now safely be enabled again.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43789
kernel lock debugging unveiled that we should not call
of_reset_control_get inside a clock's enable operation (see below)
move of_reset_control_* previously used in pllb_clk_enable to new
pllb_clk_prepare and pllb_clk_unprepare functions.
use a container to carry runtime information.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2742 lockdep_trace_alloc+0xb8/0xfc()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.26 #6
[<c001a6ac>] (unwind_backtrace) from [<c0016dec>] (show_stack+0x10/0x14)
[<c0016dec>] (show_stack) from [<c0194f68>] (dump_stack+0x7c/0x94)
[<c0194f68>] (dump_stack) from [<c0021b50>] (warn_slowpath_common+0x68/0x8c)
[<c0021b50>] (warn_slowpath_common) from [<c0021ba4>] (warn_slowpath_fmt+0x30/0x40)
[<c0021ba4>] (warn_slowpath_fmt) from [<c0061b30>] (lockdep_trace_alloc+0xb8/0xfc)
[<c0061b30>] (lockdep_trace_alloc) from [<c00cb740>] (kmem_cache_alloc+0x1c/0xf8)
[<c00cb740>] (kmem_cache_alloc) from [<c01d33c8>] (of_reset_control_get+0xe8/0x12c)
[<c01d33c8>] (of_reset_control_get) from [<c0269228>] (pllb_clk_enable+0x14/0xbc)
[<c0269228>] (pllb_clk_enable) from [<c0265738>] (__clk_enable+0x54/0xa0)
[<c0265738>] (__clk_enable) from [<c0265acc>] (clk_enable+0x18/0x2c)
[<c0265acc>] (clk_enable) from [<c04325f8>] (oxnas_pcie_probe+0x3b8/0x6a0)
[<c04325f8>] (oxnas_pcie_probe) from [<c01f2510>] (platform_drv_probe+0x18/0x48)
[<c01f2510>] (platform_drv_probe) from [<c01f1070>] (driver_probe_device+0xd8/0x24c)
[<c01f1070>] (driver_probe_device) from [<c01f1298>] (__driver_attach+0x70/0x94)
[<c01f1298>] (__driver_attach) from [<c01ef728>] (bus_for_each_dev+0x4c/0x98)
[<c01ef728>] (bus_for_each_dev) from [<c01f0818>] (bus_add_driver+0xcc/0x1e8)
[<c01f0818>] (bus_add_driver) from [<c01f169c>] (driver_register+0xa0/0xe8)
[<c01f169c>] (driver_register) from [<c01f2568>] (platform_driver_probe+0x20/0xa4)
[<c01f2568>] (platform_driver_probe) from [<c0013a3c>] (do_one_initcall+0x90/0x140)
[<c0013a3c>] (do_one_initcall) from [<c0421d38>] (kernel_init_freeable+0x1e4/0x2c0)
[<c0421d38>] (kernel_init_freeable) from [<c000c214>] (kernel_init+0x8/0x104)
[<c000c214>] (kernel_init) from [<c0008768>] (ret_from_fork+0x14/0x2c)
---[ end trace 5f17ed2f61e0683f ]---
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43787
accidentally #if was used instead of #ifdef, thus gcc warned
about CONFIG_ATA_LEDS being undefined...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43786
This is a 3.14.x backport of:
"mvneta: Fix TSO and checksum for non-acceleration vlan traffic"
Upstream commits:
817dbfa5d1bc276a72c1a577310382008e8aca0a
2d39d120781a5770573dc6ed672a5a562f541aea
Fixes vlan tagging on SoC interfaces for the WRT1900AC. Useful
when using mvsw6171 driver.
Signed-off-by: Mark Milburn <mark.a.milburn@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43781
safed one level of indention by using 'continue' instead of a
lengthy if-clause.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: use logic-AND instead of '?' operator when checking for hw bug 6320
SVN-Revision: 43768
- replaced // comments by /* comments */
- added line-breaks where needed
- fixed white-space according to kernel style
- fixed some obvious spelling mistakes in comments and printks
- removed some unneeded left-overs imported from vendor code-base
- replaced printk(...) by libata macros where possible
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43767
locking for 2nd port and hwraid was added from vendor's GPL code which
doesn't comply with current kernel coding style.
- moved all global variables into host_priv
- renamed locks
- sanetized acquire() and release() parameter list
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43766
and no longer compile-in ext4 filesystem now that sata_oxnas is
also built as a module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43765
Set defaults health led to a timer heartbeet (200/800)
and populate network for:
- GuruplugServerPlus
- SheevaPlug
- SheevaPlug with eSATA
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
SVN-Revision: 43752
This maps the LAN ports to eth0 and WAN port to eth1.
Since there are two interfaces the 802.1q VLAN mode
is unnecessary and left disabled. Port-based VLANs
are used instead.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43750
When there is no device connected to the controller we should not start
the controller. This also changes between PCIe 1.0 and PCIe 2.0 speed
based on the device. This code is based on code from the new Broadcom
PCIe controller driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43748
This patch adds soc support for QCA9561 and TP9343.
TP9343 is a reduced version of QCA9561, which can be found in TP-LINK routers in China.
The qca956x_wmac has not yet been supported by ath9k.
tested on TL-WDR6500 and TL-WR882N v1 (Chinese version)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 43744
Remove read/write/rmw member functions from ar8xxx_priv
There seems to be no real benefit of the ar8xxx_priv member functions
read/write/rmw as one implementation exists for each of them only.
Especially ar8xxx_mii_rmw is assigned to priv->rmw first and then
mapped to ar8xxx_rmw.
Rename the ar8xxx_mii_.. functions to ar8xxx_.. and use them directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43742
Create helpers mii_read32 / mii_write32 for 32 bit MII ops.
Rename r3 variable to page in ar8xxx_mii_write to make it consistent
with the other ar8xxx_mii_xxxx functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43741
Factor out chip-specific parameters from ar8xxx_probe_switch.
Move the ar8xxx_chip definitions after the swops definitions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43740
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
This will allow us to drop it in the future. This patch doesn't change
the final mtdpart.c, it remains the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43696
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
It moves firmware patch code behind an extra check on board_name.
Otherwise it will calculate firmware checksum for unaffected boards.
It also reduce boottime by a md5 calculation and removes error message
on boot if firmware not found.
SVN-Revision: 43679
Restoring the config for kernel 3.14 didn't contain that change already
made to config-3.18.
It is needed to make squashfs in the kernel match the compression settings
for ARCH=arm in the framework.
If set to ARMTHUMB, boot fails due to squashfs being unreadable if the
filesystem was generated for wth ARM BCJ filter.
in include/image.mk: BCJ_FILTER:=-Xbcj $(LINUX_KARCH)
Thus the ARM filter is used for all ARM targets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43640
it should needs to depend on imx and mxs
also remove duplicate kmod definition from mxs target
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43627
The target au1000 has at least 2 different models, the
'InternetBox' and the 'MeshCube' which look very similar
from the kernel point of view but are totally different
devices which base on the same design. Populating /tmp/sysinfo
now. The 1st one has an issue which leads to a random
mac-address after each boot which is corrected now via
reading the bootloader-env. The real fix would be
converting to DTS, this is only a workaround now.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43626
This is required because it has to be called at very precise moment. See
comment in driver for details.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43611
similar to mv_sata, use nr-ports attribute from device tree.
import and adapt locking code from vendor GPL sources.
add dma controller handling, it may be used in future to avoid
full core resets similar to the vendor SDK's "progressive cleanup"
function.
this is still very dirty and aimed to first of all do things
quite exactly like the reference code. and it somehow works.
obviously there is lots of room for improvement :)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43598
sata_oxnas.c is obviously a refactored version of sata_ox820.c
which does contain this header.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43597
According to the vendor tarball, the TD-w8900GB's flash has 64k erase
block size, but CFE spans two blocks. So fixup the image offset
accordingly but keep block size at its default (64k).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: add commit message, add image offset, change nvram offset]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43572
This adds some updates to the NAND driver and refreshed the config.
Most of these changes are done in preparation for mainling it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43546
This adds some updates to the PCIe driver and refreshed the config.
Most of these changes are done in preparation for mainling it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43545
This brings ssb and bcma to wireless-testing tag master-2014-12-05
In addition it also adds the ARM-BCM5301X-Add-IRQs-to-Broadcom-s-bus-
axi-in-DTS-f.patch which adds the irq number in a way it is done in the
mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43544
I don't see that we're in an atomic context so there's no need to
busy-wait. Therefore replace the delay with sleep calls.
See also Documentation/timers/timers-howto.txt. It states:
"In general, use of mdelay is discouraged and code should
be refactored to allow for the use of msleep."
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43539
Replace the fixed wait time of 1s with polling for BMCR_RESET
to be cleared on all PHYs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43538
This reverts commit c81ddddde5fd193802d511b42eb7b108aac17136 on
https://gitorious.org/openwrt-oxnas/openwrt-oxnas.git
which removed patches and config for 3.14.
[arm_introduce-dma-fiq-irq-broadcast patch was renamed to match 3.18]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43520
similar to what was observed on kirkwood this significantly accelerates
btrfs write operations.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43498
gpio-beeper module was added to the kernel recently.
Make use of it to drive the piezoelectric buzzer of the kd20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43496
This is a swconfig driver for the Marvell 88E6171 switch,
which is a 7-port GigE switch with two CPU ports and 64
802.1q VLANs.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43486
Factor out set_mirror_regs to ar8xxx_chip.
Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43468
Factor out info whether switch should be configured at probe stage
to ar8xxx_chip. Remove related chip_is_... checks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43466
Patch to add the buildprofile for the GL-Init-6408A-v1 and the GL-Inet-6416A-v1
Both devices are identical, only difference is one comes with 8MB flash and
the other with 16MB flash
Official website: http://www.gl-inet.com/w/?page_id=241&lang=en
Comprehensive list of specs: https://revspace.nl/GL-Inet
Signed-off-by: Martijn Zilverschoon <martijn@friedzombie.com>
SVN-Revision: 43462
Add the required nodes for the interrupt controllers and register
them through DT when a DTB is present.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43457
Add irq-domain aware irqchip drivers for the irq controllers of bcm63xx
and switch to use them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43454
At least on my Iomega ix2-200 system, this makes btrfs writes about 30% faster.
Signed-off-by: Richard Kunze <richard.kunze@web.de>
SVN-Revision: 43434
This patch introduces some code that is compiled in whenever
CONFIG_BRIDGE_NETFILTER is built, with the code called from code compiled under
CONFIG_BRIDGE, CONFIG_BRIDGE_IGMP_SNOOPING or CONFIG_BRIDGE_NF_EBTABLES.
Unfortunately, these options aren't setting explicitly the dependency they now
have on CONFIG_BRIDGE_NETFILTER, for obvious reasons for CONFIG_BRIDGE.
However, this is not working really well when CONFIG_BRIDGE_NETFILTER is built
as a module, since code statically compiled will now use a function that is not
in the kernel image, which makes the linker grumpy.
Solve this by removing the option to build CONFIG_BRIDGE_NETFILTER as a module,
and protect our function definition by an IS_BUILTIN instead of a IS_ENABLED
macro. This fixes the issue for CONFIG_BRIDGE and CONFIG_BRIDGE_IGMP_SNOOPING.
Fixing CONFIG_BRIDGE_NF_EBTABLES has to be handled a bit differently, since it
directly references a variable that will not be declared if
CONFIG_BRIDGE_NETFILTER is not set. Protect the variable affectations by an
ifdef to make sure this doesn't happen.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43419
This is the oxnas target previously developed at
http://gitorious.org/openwrt-oxnas
Basically, this consolidates the changes and addtionas from
http://github.org/kref/linux-oxnas
into a new OpenWrt hardware target 'oxnas' adding support for
PLX Technology NAS7820/NAS7821/NAS7825/...
formally known as
Oxford Semiconductor OXE810SE/OXE815/OX820/...
For now there are 4 supported boards:
Cloud Engines Pogoplug V3 (without PCIe)
fully supported
Cloud Engines Pogoplug Pro (with PCIe)
fully supported
MitraStar STG-212
aka ZyXEL NSA-212,
aka Medion Akoya P89625 / P89636 / P89626 / P89630,
aka Medion MD 86407 / MD 86805 / MD 86517 / MD 86587
fully supported, see http://wiki.openwrt.org/toh/medion/md86587
Shuttle KD-20
partially supported (S-ATA driver lacks support for 2nd port)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43388
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
With kernel 3.14 dts target p1010rdb was renamed to p1010rdb-pa.
To maintain compatibility define p1010rdb-pa as new standard and
copy p1010rdb.dts to p1010rdb-pa.dts under 3.10.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43371
If there is no board support in the kernel, it does not make sense to
build images for devices. So drop any images for board ids for which
there are nc corresponding board_info structs in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43364
Patch reverts 43332 which seems to cause issues with VLAN functionality.
Add a specific check to check whether ANEG is still enabled and re-enable
it if necessary. Disable generic phy soft reset for kernel >=3.16.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43356
This target can be emulated using ARM's Foundation_V8 simulator
software or qemu-system-aarch64 using the command-line described in the
README file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43355
Move compatible strings from board structs into separate table. This
allows for several board compatibles to match to the same board in case
e.g. only the flash size / partitions differ.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43341
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43334
Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43333
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43332
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43331
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43330
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43329
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43328
wg302v1_fixup() looks for the ATAG_CMDLINE atag, it doesn't find it and
so it takes the last atag in the list and overwrites non allocated
memory.
The side effects are corrupted vital data and a kernel that doesn't
boot. More details here https://dev.openwrt.org/ticket/18356
The fix appends the fixup to the command line and updates the atag only
when it finds it.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43320
Few notes:
- redboot partitions are unusable
- redboot declares only 16M of RAM, hence the mem arg in cmdline and separate kernel config
- boots fine but only ethernet works for now
- split wiliboard and raidsonic boards into different subtargets
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 43319
This patch adds 3.14 kernel support for the mpc85xx platform.
Works fine here with a TL-WDR4900 which seems to be the only
supported device using this platform.
There might be differences depending on HW version, therefore
I'd ask others to test too.
Changes to 3.10
missing config options added to 3.14 config file
patch 001: rebased
patch 100: rebased
patch 110: rebased
patch 120: rebased
patch 130: rebased
patch 140: minor adjustment
patch 200: removed, change went upstream
patch 210: rebased
patch 220: removed, change went upstream
patch 750: new, fixes an issue with ethernet port autoneg being
disabled due to changes in kernel phy handling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43308
still no sound but the codec is properly detected now, powers up and i can hear
noise on the speakers.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43305
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43303
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43301
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43292
Without this patch the UBIFS driver is unable to attach to the mtd
storage and mount the root FS.
Fixes a kernel panic with Netgear WNDR4300/3700v4 devices.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43287
the SDK does a bit of extra init that we did not do yet when using an external mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43245
