Commit graph

217 commits

Author SHA1 Message Date
Felix Fietkau
12c84f8eeb ar71xx: add some code to detect DMA stuck conditions on ar7240
SVN-Revision: 27975
2011-08-13 22:30:14 +00:00
Felix Fietkau
85ccc74e1b ar71xx: on ar724x only reset the link status in the restart handler, the fast reset takes care of DMA stuck issues
SVN-Revision: 27973
2011-08-13 21:49:46 +00:00
Felix Fietkau
4b75394056 ar71xx: fix ethernet FIFO state corruption on ar7240
When starting/stopping DMA sometimes the FIFO state gets corrupted,
leading to wildly fluctuating latencies or packet data corruption.
Fix this by issuing a fast MAC reset as soon as the link is detected
as up. Fixes #9689, #9405

SVN-Revision: 27896
2011-08-04 17:36:31 +00:00
Felix Fietkau
d2aeca6b6d ag71xx: fix memory corruption issues on ar7240 on ethernet start/stop
When the DMA engine state gets corrupted due to a hardware issues, it
often won't stop rx until a full reset is issued. In that case the hardware
must keep a valid descriptor, otherwise it will write to random places in
system RAM, triggering random crashes. To fix this, keep a dummy descriptor
without a buffer that keeps the DMA engine in a sane state until the reset
is done

SVN-Revision: 27895
2011-08-04 17:36:27 +00:00
Felix Fietkau
500c3a1475 ar71xx: fix MAC/MDIO reset mask handling
SVN-Revision: 27894
2011-08-04 17:36:23 +00:00
Felix Fietkau
c7173a211d ar71xx: reinitialize global switch settings after reset on ar7240
SVN-Revision: 27705
2011-07-20 14:39:47 +00:00
Felix Fietkau
ca473833c4 ar71xx: configure address aging on ar7240
SVN-Revision: 27704
2011-07-20 14:39:42 +00:00
Felix Fietkau
fefc79f3cb ar71xx: reset the phy in the ethernet init on ar724x
SVN-Revision: 27703
2011-07-20 12:04:34 +00:00
Felix Fietkau
005fe5d1fd ar71xx: make sure that rx and interrupts are disabled before issuing the hardware reset
SVN-Revision: 27702
2011-07-20 12:04:29 +00:00
Felix Fietkau
e7ab000008 ar71xx: increase the delay after the ethernet MAC reset
SVN-Revision: 27701
2011-07-20 12:04:25 +00:00
Felix Fietkau
255dcaa3a6 ar71xx: fix an unused variable warning
SVN-Revision: 27700
2011-07-20 12:04:20 +00:00
Felix Fietkau
f3d693c0ee ar71xx: do not reset the hardware on transmit timeout - this would mess up the up the PHY state
SVN-Revision: 27568
2011-07-09 06:30:13 +00:00
Felix Fietkau
2806c75c07 ag71xx: keep the rx engine stopped while the link is not up, should hopefully fix stability issues from #9405
SVN-Revision: 27567
2011-07-09 06:29:46 +00:00
Gabor Juhos
d98476c6bd ar71xx: merge 2.6.39 patches
Also remove the old UART driver for ar933x.

SVN-Revision: 27314
2011-06-29 08:57:37 +00:00
Gabor Juhos
6627574e57 ar71xx: add 2.6.39 support
SVN-Revision: 27310
2011-06-29 08:57:32 +00:00
Gabor Juhos
e6af77a1c8 ar71xx: cleanup AR933X UART driver
SVN-Revision: 27222
2011-06-19 13:17:51 +00:00
Gabor Juhos
b7e016ba42 ar71xx: use ar933x_uart.h in the AR933X serial driver
SVN-Revision: 27166
2011-06-13 08:12:40 +00:00
Gabor Juhos
13363d9129 ar71xx: setup wdt_clock for AR913X to avoid a kernel bug
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 27102
2011-06-04 12:30:10 +00:00
Felix Fietkau
31dd60689e Revert "ar71xx: only enable the rx engine after the link is up..."
It messes up the DMA state when the link goes down

SVN-Revision: 27088
2011-06-01 18:15:43 +00:00
Gabor Juhos
b460bc6f12 ar71xx: add serial driver for the AR933X UART
SVN-Revision: 27065
2011-05-31 22:53:40 +00:00
Gabor Juhos
88c45e3130 ar71xx: the watchdog uses the reference clock on the AR933x SoCs
SVN-Revision: 27060
2011-05-31 22:53:34 +00:00
Gabor Juhos
0677e16248 ar71xx: Fix header offset for newer WRT160NL models
Newer WRT160NLs have a flash chip with 4K erase blocks instead of 64K,
resulting in miscalculated partition sizes.
Since the actual sizes did not change, hardcode them to their current
sizes, and make sure they are at least one erase block big (in case Cisco
decides to start to use chips with 128K erase blocks).

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>

SVN-Revision: 27049
2011-05-31 22:53:20 +00:00
Gabor Juhos
60d5abbc27 ar71xx: ag71xx: make ring sizes configurable via ethtool
SVN-Revision: 27041
2011-05-31 22:53:10 +00:00
Gabor Juhos
7a2651f633 ar71xx: ag71xx: prepare to make ring sizes configurable
SVN-Revision: 27040
2011-05-31 22:53:09 +00:00
Gabor Juhos
669aba3871 ar71xx: ag71xx: nuke unused AG71XX_TX_FIFO_LEN define
Reported-by: Dave Täht <dave.taht@gmail.com>

SVN-Revision: 27039
2011-05-31 22:53:07 +00:00
Felix Fietkau
2b5402d128 ar71xx: only enable the rx engine after the link is up, fixes a race condition that got rx stuck when the interface is brought up during lots of inbound traffic (thx, matteo)
SVN-Revision: 27035
2011-05-30 23:08:01 +00:00
Felix Fietkau
0ebc93831f ar71xx: disable flow control for ar724x, it can get stuck in a loop of continously sending MAC pause frames
SVN-Revision: 27034
2011-05-30 23:07:57 +00:00
Matteo Croce
4deecea26b ar71xx: detect link on LAN ports
SVN-Revision: 26922
2011-05-17 11:12:56 +00:00
Matteo Croce
c0c2e18452 use correct macros and frame size in ag71xx
SVN-Revision: 26890
2011-05-14 23:10:06 +00:00
Gabor Juhos
5d77f370d6 ar71xx: ag71xx: make switch register access atomic
Reading of the PHY registers occasionally returns with bogus values
under heavy load. This misleads the PHY driver and thus causes false
link/speed change notifications which leads to performance loss.

This is easily noticable during an iperf session:

...
[  3] 52.0-53.0 sec  11.3 MBytes  94.4 Mbits/sec
[  3] 53.0-54.0 sec  11.4 MBytes  95.4 Mbits/sec
eth1: link down
br-lan: port 2(eth1) entering forwarding state
eth1: link up (100Mbps/Full duplex)
br-lan: port 2(eth1) entering forwarding state
br-lan: port 2(eth1) entering forwarding state
[  3] 54.0-55.0 sec  6.75 MBytes  56.6 Mbits/sec
[  3] 55.0-56.0 sec  0.00 Bytes  0.00 bits/sec
[  3] 56.0-57.0 sec  10.5 MBytes  88.1 Mbits/sec
...
[  3] 169.0-170.0 sec  11.4 MBytes  95.4 Mbits/sec
[  3] 170.0-171.0 sec  11.4 MBytes  95.4 Mbits/sec
eth1: link up (10Mbps/Half duplex)
[  3] 171.0-172.0 sec  7.63 MBytes  64.0 Mbits/sec
[  3] 172.0-173.0 sec  9.38 MBytes  78.6 Mbits/sec
eth1: link up (100Mbps/Full duplex)
[  3] 173.0-174.0 sec  11.3 MBytes  94.4 Mbits/sec
[  3] 174.0-175.0 sec  11.4 MBytes  95.4 Mbits/sec

SVN-Revision: 26856
2011-05-08 16:32:53 +00:00
Gabor Juhos
3711658281 ar71xx: ag71xx: fix section mismatch warnings
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.

The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.

SVN-Revision: 26855
2011-05-08 13:30:36 +00:00
Gabor Juhos
ef53029870 ar71xx: ag71xx: fix build error if debugfs is enabled
SVN-Revision: 26854
2011-05-08 13:30:26 +00:00
Gabor Juhos
8b67d748cb ar71xx: ag71xx: add debugfs entry for [rt]x_ring
SVN-Revision: 26845
2011-05-07 12:40:34 +00:00
Gabor Juhos
2166432ba0 ar71xx: ag71xx: add timestamps to ag71xx_buf
SVN-Revision: 26844
2011-05-07 12:40:28 +00:00
Gabor Juhos
896e1d1ab4 ar71xx: ag71xx: use dynamically allocated buffer for napi_stats
SVN-Revision: 26843
2011-05-07 12:40:26 +00:00
Gabor Juhos
a6708d20d1 ar71xx: ag71xx: use debugfs_remove_recursive
SVN-Revision: 26842
2011-05-07 12:40:25 +00:00
Gabor Juhos
a8bf5e3cdb ar71xx: rename ar934x_ref_freq to ar71xx_ref_freq
Also initialize that for each SoC and print its value along with the
other frequencies.

SVN-Revision: 26561
2011-04-09 18:47:52 +00:00
Gabor Juhos
2b064bb398 ar71xx: add support for the watchdog of the AR934x SoCs
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>

SVN-Revision: 26516
2011-04-07 20:53:10 +00:00
Felix Fietkau
41ee4a283c ar71xx: only allow internal access to the ar7240 switch, export the MDIO bus behind the switch instead
SVN-Revision: 26393
2011-04-02 00:47:29 +00:00
Felix Fietkau
acbb3e50e7 ar71xx: frequent ethernet mac resets upset the MDIO bus on ar7240, so do not run them on every device open, only on tx timeouts
SVN-Revision: 26392
2011-04-02 00:47:25 +00:00
Gabor Juhos
23a6173099 ar71xx: use gpio_*_cansleep calls in the rb4xx NAND driver
SVN-Revision: 24944
2011-01-09 09:29:45 +00:00
Gabor Juhos
920a34c0ce ar71xx: drivers/ar71xx_wdt: fix size argument passed to copy_to_user()
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23983
2010-11-12 18:52:45 +00:00
Gabor Juhos
3106aea40b ar71xx: drivers/ag71xx: remove deprecated usage of IRQF_SAMPLE_RANDOM
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23982
2010-11-12 18:52:28 +00:00
Gabor Juhos
30ef7d55fc ar71xx: use pr_* functions in drivers
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23981
2010-11-12 18:52:12 +00:00
Gabor Juhos
fddf3b8dac ar71xx: drivers/rb4xx_nand: remove C++ comment usage
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23980
2010-11-12 18:51:55 +00:00
Gabor Juhos
f4d5c885e4 ar71xx: return statements does not need parenthesis
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23979
2010-11-12 18:51:38 +00:00
Gabor Juhos
e244e1c7cd ar71xx: fix inline attribute location
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23978
2010-11-12 18:51:21 +00:00
Gabor Juhos
acd8ad4de5 ar71xx: wrap long lines
(build errors has been fixed - juhosg)

Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23977
2010-11-12 18:51:04 +00:00
Gabor Juhos
500fac1735 ar71xx: fix whitespaces nits
(build error has been fixed - juhosg)

Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>

SVN-Revision: 23975
2010-11-12 18:50:29 +00:00
Felix Fietkau
6656450c6d ar71xx: fix more section mismatches
SVN-Revision: 23575
2010-10-21 18:42:16 +00:00