Commit graph

304 commits

Author SHA1 Message Date
Felix Fietkau
0ec9253b9d ramips: fix WSR-1166 partition table
- Fix typo in board_data partition start address
- Increase board_data partition size in order to exploit all flash size

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>

SVN-Revision: 48751
2016-02-22 08:54:32 +00:00
John Crispin
fc47eb0794 ralink: fix mt7628 ehci support
the u2_phy init was missing

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48747
2016-02-19 16:38:04 +00:00
John Crispin
8b38a9450b ramips: Add support for Phicomm PSG1208
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

SVN-Revision: 48721
2016-02-15 18:45:22 +00:00
John Crispin
ba53b33453 ramips: Support LEDs on D-Link DIR-860L B1
Adds the required gpio definitions.

Signed-off-by: Johannes Wienke <languitar@semipol.de>

SVN-Revision: 48715
2016-02-12 09:29:23 +00:00
John Crispin
9f9682a79b ramips: Add support for Netgear EX2700
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.

What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>

SVN-Revision: 48698
2016-02-12 08:29:33 +00:00
John Crispin
6801c4e33e ramips: HLK-RM04 - Enable GPIO14 for WPS button
The top half of UARTF on the HLK-RM04 is used for GPIO.

  mode 1   mode 2
   RIN     GPIO14
   DSR_N   GPIO13
   DCD_N   GPIO12
   DTR_N   GPIO11
   RXD     GPIO10
   CTS_N   GPIO09
   TXD     GPIO08
   RTS_N   GPIO07

This patch applies 3'b101 mode to UARTF:

   GPIO14
   GPIO13
   GPIO12
   GPIO11
   RXD
   CTS_N
   TXD
   RTS_N

Because the base rt5350.dtsi file forces 3'b000 mode, remove the pin setting from this file and apply it directly to the files that inherit from it (WIZFI630A.dts and WT1520.dtsi).  This change makes the rt5350.dtsi file consistent with the mt7620a.dtsi file.

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48665
2016-02-08 08:26:27 +00:00
John Crispin
7f672e66f8 rampis: HLK-RM04 - Setup I2C as GPIO
The I2C function of the RT5350 SoC on the HLK-RM04 is used for GPIO1 and GPIO2.

Take note that the I2C_SD pin is GPIO1 on the RT5350 and is exposed on the HLK-RM04 as GPIO0
Likewise the I2C_SCLK pin is GPIO2 on the RT5350 and is exposed on the HLK-RM04 as GPIO1

 group   mode 1    mode 2   hlk-rm04 pin & export
  i2c    i2c_sd    gpio1   (pin 8, hlk-rm04:gpio0)
  i2c    i2c_sclk  gpio2   (pin 9, hlk-rm04:gpio1)

reference:
  http://www.hlktech.net/product_detail.php?ProId=39
  http://cdn.sparkfun.com/datasheets/Wireless/WiFi/RT5350.pdf

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48664
2016-02-08 08:26:19 +00:00
John Crispin
480e15f2ce ramips: HLK-RM04 - Fix push button functions
The RESET button of the HLK-RM04 is connected to GPIO0, linux function 0x198
The WPS button of the HLK-RM04 is connected to GPIO14, linux function 0x211

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48663
2016-02-08 08:26:11 +00:00
John Crispin
1f26091242 ramips: HLK-RM04 - Remove power LED config
The power LED on the HLK-RM04 is hard wired to the power bus and is not under GPIO control, remove the bogus config for it.
(Note that GPIO0 is actually connected to the RESET button.)

Signed-off-by: John Clark <inindev@gmail.com>

SVN-Revision: 48662
2016-02-08 08:26:02 +00:00
John Crispin
f51f92d7e9 ramips: fix serial baudrate for final version of ZBT-WG2626 board
The bootloader was updated and now uses 115200 instead of 57600 baud
for the serial console. Change this also in OpenWrt's DTS, so the rate
is consistent for bootloader and linux kernel output.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 48359
2016-01-19 10:16:30 +00:00
Felix Fietkau
56608a777e ramips: fix duplicate /dts-v1/ line for WRTNODE2
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>

SVN-Revision: 48138
2016-01-06 00:04:14 +00:00
John Crispin
eb9fccc440 ralink: update the usb phy driver to the version sent upstream
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48114
2016-01-04 14:21:17 +00:00
John Crispin
9b675a2a33 ralink: fix USB compatible strings
switch to the upstream compatible strings for ehci and ohci support.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 48113
2016-01-04 14:21:11 +00:00
John Crispin
6ca6a98622 ramips: Remove LED GPIO definitions in MQmaker WiTi device tree
LED's were defined wrong in the device tree file, they are hardware driven because they are connected directly to the switch chip and wireless chips respectively, thus no GPIO addresses are assigned to them. It is safe to remove them from the device tree file to stop confusion.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 48055
2016-01-01 21:20:54 +00:00
John Crispin
de7dce21a3 ralink: add WRTnode2 platform and led support
Signed-off-by: xzmu <xzmu@wrtnode.com>

SVN-Revision: 48049
2016-01-01 21:19:50 +00:00
Felix Fietkau
c55d8d4253 ramips: set the wifi mac address to the same as LAN on witi
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48029
2016-01-01 18:58:02 +00:00
Felix Fietkau
eaf8889cf8 ramips: add a script to fix up the broken mac address on the witi board
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48027
2016-01-01 18:57:39 +00:00
Felix Fietkau
28ec4e0e71 ramips: fix inverted LEDs for RE6500
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>

SVN-Revision: 48022
2016-01-01 12:27:45 +00:00
Felix Fietkau
2c4faaed74 ramips: add mac address assignment for eth0 on RE6500
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48021
2016-01-01 12:26:38 +00:00
Felix Fietkau
d65eda48b7 ramips: fix firmware partition size
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>

SVN-Revision: 48020
2016-01-01 12:26:30 +00:00
Felix Fietkau
11c697015f ramips: fix memory size for RE6500
Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>

SVN-Revision: 48019
2016-01-01 12:26:26 +00:00
Felix Fietkau
3e807886d0 ramips: disable NAND device in mt7621.dtsi to fix boot errors on many devices
Enable it from .dts files that need it, also remove redundant properties

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47936
2015-12-19 11:07:29 +00:00
Felix Fietkau
32877b31dc ramips: update DTS files to use jedec,spi-nor compatible string for m25p80 to fix probe issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47935
2015-12-18 22:26:40 +00:00
John Crispin
651e620de5 ralink: fixup devicetree files to work with new ethernet driver
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47900
2015-12-17 09:25:57 +00:00
John Crispin
4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
John Crispin
8470e30a76 ramips: move partition definitions out of mt7621.dtsi file
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47876
2015-12-12 06:42:11 +00:00
John Crispin
e610cdfc8a ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47875
2015-12-12 06:42:05 +00:00
Felix Fietkau
77bedbe80d Revert "ramips: use gic timer as clocksource for mt7621"
This reverts commit 270a2afcc544ca14e79198346e7e186033472ae7.

SVN-Revision: 47872
2015-12-11 19:22:15 +00:00
John Crispin
9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00
John Crispin
6cbb1be464 ramips: Fix support for PBR-M1 board
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.

The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 47844
2015-12-11 15:03:50 +00:00
John Crispin
abd11be13c ramips: use gic timer as clocksource for mt7621
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
  Will work on proper frequency detection later.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47843
2015-12-11 15:03:39 +00:00
John Crispin
a87272ebfb ramips: enable CPS for mt7621
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.

This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47842
2015-12-11 15:03:27 +00:00
John Crispin
81c999bbda ramips: mt7621: use symbolic names of gic interrupt settings
This also adds dts nodes for cpc and mc for documentation purposes

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47836
2015-12-11 15:02:13 +00:00
John Crispin
6df4426245 ralink: bump to the target to v4.3
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47831
2015-12-10 19:06:32 +00:00
John Crispin
82557aee85 ramips: adapt VoCore to new second spi device code
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47667
2015-11-28 23:24:52 +00:00
John Crispin
8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00
John Crispin
e9baf8265b ramips: add support for Youku YK1
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47617
2015-11-24 18:29:02 +00:00
John Crispin
c550ad3d3a ramips: update dtsi files to support second spi device
Signed-off-by: Michael Lee <igvtee@gmail.com>

SVN-Revision: 47580
2015-11-22 11:49:13 +00:00
John Crispin
40ddc71cc9 ramips: init usb power for Lenovo Y1S
Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47557
2015-11-21 21:24:38 +00:00
John Crispin
dc699dd547 ramips: minor tweak to the lks7688 baord name
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47388
2015-11-05 10:01:23 +00:00
John Crispin
165244a222 ramips: add support for ZBT WG2626
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351
2015-11-02 10:18:19 +00:00
John Crispin
0f4b153e3d ramips: add eeprom mtd partition to the Asus RP-N53 dts
This patch adds the eeprom property to the dts for the Asus RP-N53. It is necessary to get the wifi in the soc working.

Signed-off-by:  Alberto Mattea <alberto@mattea.info>

SVN-Revision: 47350
2015-11-02 10:18:09 +00:00
John Crispin
3760b95702 ramips: add support for Dovado tiny AC
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
2015-11-02 10:17:51 +00:00
John Crispin
7295e9fb8b ramips: add alsa support
add the SDK alsa driver. this has only been tested on mt7628/88 and wm8960.
mt7620 is only compile tested.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47205
2015-10-19 10:07:54 +00:00
John Crispin
51dd991d39 ramips: add LinkIt Smart7688 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47203
2015-10-19 10:07:38 +00:00
John Crispin
b0f7e6bc83 ramips: fix /target/linux/ramips/dts/HC5XXX.dtsi
dtb complained about those lines

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47151
2015-10-07 08:00:40 +00:00
John Crispin
ccf89e71f2 ramips: add support for 16MB VoCore
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47120
2015-10-05 10:27:00 +00:00
John Crispin
948e67cb16 ramips: fix size-cells for spi nodes
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 47119
2015-10-05 10:26:54 +00:00
John Crispin
e6e373d348 ramips: Add DTS files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
  1: Merged most stuff into dtsi file
  2: Remove unnecessary empty lines.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47112
2015-10-05 10:25:53 +00:00
John Crispin
7ad419a9f1 ralink: add irq to mt7628 gpio node
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47076
2015-10-01 19:12:14 +00:00