Commit graph

1119 commits

Author SHA1 Message Date
Piotr Dymacz
e33dcd1cfe ar71xx: add support for YunCore CPE830
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.

Use the same flash approach as for YunCore AP90Q.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
eb9ba2b91e ar71xx: add support for YunCore CPE870
YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341.
Short specification:

- 535/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm
- internal 14 dBi panel antenna
- 8x LED, 1x button
- UART (JP1) header on PCB

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. setenv bootcmd "bootm 0x9f020000"
5. saveenv && reset

Vendor firmware access (login/password): Admin/5up

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
01dda0659e ar71xx: add support for YunCore AP90Q
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:

- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Flash instruction under vendor fimrware, using telnet/SSH:

1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
16afa08d19 ar71xx: add support for COMFAST CF-E380AC v1 and v2
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.

There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size

Version number is available only inside vendor GUI,
hardware and markings are the same.

Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Piotr Dymacz
31952dbd1c ar71xx: add support for COMFAST CF-E320N v2 and CF-E520N/CF-E530N
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.

All 3 devices are based on Qualcomm/Atheros QCA9531 v2.

COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Henryk Heisig
0d760bfba8 ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partition
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-16 11:01:18 +01:00
FUKAUMI Naoki
0165203304 ar71xx: add support for Buffalo BHR-4GRV2
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2016-11-16 10:54:33 +01:00
Matthias Schiffer
7ef0d7c4fc
ar71xx: enable HSR tuner on Ubiquiti UAP Outdoor+
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-11-15 18:54:07 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Christian Mehlis
7cb82d4b70 ar71xx: fix ethernet on wpj344 board
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
2016-10-31 12:52:56 +01:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Julius Schulz-Zander
a71a8955f2 ar71xx: add support for TP-Link WR802N v1
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.

Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
2016-10-26 12:37:45 +02:00
Chris Blake
28dd52b079 ar71xx: add mac partition to the MR12/MR16
On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space
after u-boot-env is used to store the boards Mac address. Sadly as this
was removed on any device already on OpenWRT/LEDE, moving forward a new,
64k partition named "mac" will be used to store the mac address for the
device (which is the minimum size). This allows users to properly set
the correct MAC, without editing the ART partition (which holds the same
MAC for all devices).

The reason the space is taken from kernel instead of rootfs is currently
kernels are only 1.3MB, so that way we can leave the current rootfs
space alone for users who fully utilize the available storage space.

Once this partition is added to a device, you can set your MAC doing the
following:

mtd erase mac
echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5
sync && reboot

Where 00:18:0a:33:44:55 is your MAC address.

This was tested, and confirmed working on both the MR12 and MR16.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-10-26 12:37:45 +02:00
Jing Lin
7ba9a3a504 ar71xx: Add support to DomyWifi DW33D
Signed-off-by: Jing Lin <mumuqz@163.com>
2016-10-25 17:51:08 +02:00
Henryk Heisig
f5aa459043 ar71xx: Add support to TP-Link EAP120
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-18 09:18:55 +02:00
Christian Lamparter
098f7156cc ar71xx: add support for the Airtight C-60
This patch adds support for the Airtight C-60.

SOC:	Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM:	128 MiB
NOR:	MX25L3205D 4MiB
NAND:	ST Micro NAND 32MiB 3,3V 8-bit
SW-NET:	AR8327N (2 Ports)
WLAN1:	Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2:	Dual-Band AR9300 Rev:4 PCIe Chip

The switch is setup for an accesspoint:
	LAN1: (gigabit) is the wan-port.
	LAN2: (fast ethernet) is bridged with the br-lan.

Flashing Guide (via initramfs):
  1. Connect a PC to the serial port of the C-60.
     power up the C-60.

     Enter u-boot command prompt:
     #> nand erase
     #> setenv bootcmd "bootm 0x9f060000"
     #> saveenv
     #> setenv ipaddr 192.168.1.1
     #> setenv netmask 255.255.255.0
     #> setenv serverip 192.168.1.100
     #> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
     #> tftpboot
     #> bootm

  2. Wait for the C-60 to boot LEDE.
     On the root prompt. Enter:
     # ubiformat /dev/mtd4
     # ubiattach -p /dev/mtd4

  3. After that copy the sysupgrade.tar onto the router and run:
     # sysupgrade sysupgrade.tar

     to flash the image.

Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2016-10-15 11:36:50 +02:00
Matthias Schiffer
594f0e80ce
ar71xx: add kernel support for D-Link DIR-869 A1
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:36 +02:00
Piotr Dymacz
92870eac27 ar71xx: comsetic cleanups in files/arch/mips/ath79/{Makefile,machtypes.h}
Keep everything in alphabetical order and aligned in columns.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Piotr Dymacz
c142df3094 ar71xx: fix LED names for GL Innovations boards
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-10-04 11:50:50 +02:00
Chris Blake
68d649f5cd ar71xx: add support for Cisco Meraki Z1 Cloud Managed Teleworker Gateway
This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2016-09-27 17:50:22 +02:00
Felix Fietkau
83997146e7 ar71xx: disable flow control to the built-in switch on AR934x
It apparently causes a regression on some devices if the ethernet cable
is plugged in while booting.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-08-25 11:54:31 +02:00
Piotr Dymacz
f478fba663 ar71xx: add support for Zbtlink ZBT-WE1526
Zbtlink ZBT-WE1526 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 5x 10/100 Mbps Ethernet
- 1x USB 2.0
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- two external, non-detachable antennas
- 8x LED, 1x button
- UART header (pinout: VCC, RX, TX, GND)

Flash instruction:

Use sysupgrade in vendor firmare which is based on OpenWrt.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-08-18 09:49:18 +02:00
Zhao Gang
42305ae24a ar71xx: add support for gl-mifi
This add initial support for gl-mifi.
Product page: http://www.gl-inet.com/mifi/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-24 06:38:30 +02:00
Zhao Gang
d963ddf042 ar71xx: add support for gl-ar300m
This add initial support for gl-ar300m router.
Product page: http://www.gl-inet.com/ar300m/

Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
2016-07-20 00:21:48 +02:00
Piotr Dymacz
d2c9b169b3 ar71xx: add support for jjPlus JWAP230
jjPlus JWAP230 is based on Qualcomm Atheros QCA9558 + QCA8337.
Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 2x 10/100/1000 Mbps Ethernet
- 128 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz with external PA (SST12LP15A), up to 28 dBm
- 3x MMCX connectors
- power input: 802.3at PoE or wide range DC (36-57 V)
- optional 802.3af PSE
- 1x mini-PCIe connector with PCIe, USB buses and SIM slot
- 1x mini-PCIe connector with PCIe bus
- 1x USB type-A connector
- 6x LED, 1x button (hardware reset)
- RS232 (MAX3223) and (E)JTAG headers

Default configuration:

- WAN on eth1 (RJ45 near LEDs with PoE input)
- LAN on eth0 (RJ45 near DC jack)
- left top LED set to be status LED
- all LEDs configurable form user space

Flash instruction (do it under U-Boot, using RS232):

1. tftp 0x80060000 lede-ar71xx-generic-jwap230-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Piotr Dymacz
e767980eb8 ar71xx: add support for Wallys DR531
Wallys DR531 is based on Qualcomm Atheros QCA9531 v2.
Short specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SE2576L), up to 30 dBm
- 2x MMCX connectors
- mini-PCIe connector with PCIe/USB buses and SIM slot
- 7x LED, 1x button, 1x optional buzzer
- UART, (E)JTAG and LED headers

Default configuration:

- WAN on eth1 (RJ45 near DC jack)
- LAN on eth0 (RJ45 near button)
- S4 LED set to be status LED
- all LEDs configurable form user space
- button configured for reset

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x80060000 lede-ar71xx-generic-dr531-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-07-13 20:03:10 +02:00
Felix Fietkau
be08fdd007 ar71xx: disable pdata->use_flow_control for QCA9558
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-27 12:12:40 +02:00
Felix Fietkau
75b2105cd3 ar71xx: rename ethernet pdata->builtin_switch to use_flow_control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-27 12:12:40 +02:00
Felix Fietkau
26b8db2537 ar71xx: enable flow control for ethernet MACs with built-in switch
Should fix LAN speed issues on some devices. This is an updated version
of the previously reverted commit with the same name.
It improves the check for MACs connected to a built-in switch

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-26 11:21:17 +02:00
Alexander Couzens
c2e0c41842 Revert "ar71xx/cpe510: use second wifi calibration table"
Using the high power table can damage the device in some cases.

This reverts commit bf27ac019c.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-06-16 21:11:24 -07:00
Arne Zachlod
f869ffdd62 ar71xx: mach-ubnt-xm.c convert patches to mach file
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2016-06-13 22:51:43 +02:00
Allan Nick Pedrana
e61fe4e4d7 ar71xx: add support for OpenEmbed SOM9331
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.

Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
2016-06-07 11:21:55 +02:00
Felix Fietkau
7eeb254cc4 treewide: replace nbd@openwrt.org with nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-06-07 08:58:42 +02:00
KeLei Liang
563e9d5e1b ar71xx: add WRTnode2Q support
Signed-off-by: KeLei Liang <xzmu@wrtnode.com>
2016-06-06 14:58:11 +02:00
Stijn Segers
d2a91f9853
ar71xx: Fix TL-WR841N v11 LEDs, use separate machine
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
2016-05-31 17:36:51 +02:00
Alexander Couzens
bf27ac019c ar71xx/cpe510: use second wifi calibration table
The cpe510 has two calibration tables. The first calibration
table requires to modify ath9k driver to work (patched tx gain table).

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:50 +02:00
Alexander Couzens
c5ff273d85 ar71xx/cpe510: split profile into 2 profiles cpe210 and cpe510
Split profile into 2GHz and 5GHz. The 5GHz devices are
quite "special". The 2 GHz works perfect.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-23 13:39:49 +02:00
Sven Eckelmann
f7719dca71 ar71xx: add kernel support for the OpenMesh MR1750v2
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:25 +02:00
Sven Eckelmann
8010e8a370 ar71xx: add kernel support for the OpenMesh OM2P-HSv3
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:23 +02:00
Alexander Couzens
94e23bf740 ar71xx/cpe510: enable LNA for CPE210/220/510/520
The LNA improves the rx path. Within a simple test setup
it improved the signal from -60dbm to -40dbm.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2016-05-20 13:18:57 +02:00
Felix Fietkau
5b34dffcbd ar71xx: fix DDR write buffer flushing issues with 4.4
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-05-15 20:55:39 +02:00
Cezary Jackiewicz
0b45bec22c
ar71xx: add support for TP-LINK TL-WR842N/ND v3
- CPU QCA9531-BL3A
- RAM: 64MB
- flash: 16MB
- USB

AP143 platform, similar to tl-wr841n v10/v11, but with USB

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-05-14 21:45:16 +02:00
John Crispin
cc831e23e1 ar71xx: add proper support for Archer-C7 V2
This has minor differences to the V1

Signed-off-by: John Crispin <john@phrozen.org>
2016-05-14 21:26:08 +02:00
John Crispin
f816472f78 ar71xx: Fix TP-LINK Archer-C5/C7 v2 rfkill
Fix ARCHER_C7_GPIO_BTN_RFKILL, which is attached to GPIO23

Signed-off-by: Lars Buerding <lb.wrt@metatux.net>
2016-05-12 03:29:36 +02:00
P.Wassi
8307c2fe68 ar71xx: Add support for Ubiquiti UniFi AP AC PRO
Add support for the Ubiquiti UniFi AP AC PRO
Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
P.Wassi
c855e70491 ar71xx: Rename unifiac to unifiac-lite
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.

Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
blogic
75629fb2a8 ar71xx: add TP-Link TL-WR810N support
This patch adds support for the TP-Link TL-WR810N.
https://wiki.openwrt.org/toh/tp-link/tl-wr810n

Signed-off-by: Jens Steinhauser <jens.steinhauser@gmail.com>

SVN-Revision: 49286
2016-05-10 10:43:12 +02:00
blogic
ba3ed629ea ar71xx: Fix eth0 support for Ubiquiti UniFi AP AC
Fix eth0 support for the Ubiquiti UniFi AP AC
Signed-off-by: Paul Wassi <p.wassi at gmx.at>

SVN-Revision: 49277
2016-05-10 10:43:12 +02:00
John Crispin
ee53a240ac ar71xx: Add support for the OMYlink OMY-G1
https://wiki.openwrt.org/toh/omylink/omy-g1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49258
2016-04-26 11:44:36 +00:00
Hauke Mehrtens
9759aba429 ar71xx: fix build error
This fixes a build error introduced in r49193.

This closes #22230

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49194
2016-04-17 22:03:58 +00:00
Hauke Mehrtens
00675abc3b ar71xx: fix build with kernel 4.4
The file linux/mdio-gpio.h was moved to linux/platform_data/mdio-gpio.h
in kernel 4.4

Reported-by: Arjen de Korte <arjen+openwrt@de-korte.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 49193
2016-04-17 19:10:13 +00:00
John Crispin
5f1a82ec4f ar71xx: add TP-Link TL-WA901ND-v4 support
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 49158
2016-04-09 10:26:46 +00:00
John Crispin
d9799dea89 ar71xx: add support for Compex WPJ342
OpenWrt can be flashed with following uboot commands:

tftpboot 0x80500000 openwrt-ar71xx-generic-wpj342-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 49157
2016-04-09 10:26:41 +00:00
John Crispin
886cb9a744 ar71xx: add kernel support for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49149
2016-04-09 10:26:15 +00:00
John Crispin
69965212bd ar71xx: add kernel support for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49141
2016-04-09 10:25:47 +00:00
John Crispin
8e2a35afc6 ar71xx: WPN824N: enable buttons
Enable buttons connected to the GPIOs of the AR9285.

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 49109
2016-04-01 07:12:07 +00:00
John Crispin
38a48a9b42 ar71xx: WPN824N: set WLAN LED name
Make use of ap9x_pci_setup_wmac_led_name() to set the name of the WLAN
LED.

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 49108
2016-04-01 07:12:03 +00:00
John Crispin
ba2d1ccffa ar71xx: WNR2200: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2200 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49101
2016-04-01 07:11:34 +00:00
John Crispin
3da1ef38c1 ar71xx: WNR2200: fix for random WLAN MAC
Fix for invalid/random/duplicate WLAN MAC address in WNR2200.
Permanent platform MAC is calculated and assigned during system startup.
WLAN MAC follows wired Ethernet interface addresses.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49100
2016-04-01 07:11:27 +00:00
Luka Perkov
8258f8edb6 ar71xx: cosmetic fix of alfa ap120c/ap96 ordering
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49086
2016-03-24 21:09:34 +00:00
Luka Perkov
ebaba15331 ar71xx: add support for ap120c
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 49082
2016-03-23 22:31:38 +00:00
John Crispin
5b2d89f060 ar71xx: WNR1000v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49076
2016-03-23 12:52:35 +00:00
John Crispin
58143e9b65 Revert "ar71xx: Clear bits in ath79_setup_qca955x_eth_cfg"
Not all mach-* files set all boards correctly in ETH_CFG. They depend on
some preset values by u-boot which were not previously modified by
ath79_setup_qca955x_eth_cfg. Avoiding to modify them in this function keeps
it backward compatible for these boards.

This reverts commit 119b8ab2c2eac237ec4e9c4d0ed53df22b5c6978.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49072
2016-03-23 12:52:20 +00:00
John Crispin
b269a3520d Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x"
The default delays RXD 3. RDV 3, TXD 0, TXE 0 doesn't seem to work for some
boards. These boards depend on the preset values of u-boot which may
differ.

This reverts commit f2d4bb96b62512caa161dcc2867c91692fb16a38.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49071
2016-03-23 12:52:17 +00:00
John Crispin
26d18d4e07 ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR1750
The MR1750 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR1750 can be used instead.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49070
2016-03-23 12:52:12 +00:00
John Crispin
bdf76faa3e ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR900
The MR900 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR900 can be used instead.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49069
2016-03-23 12:52:09 +00:00
John Crispin
1cdd3403ba ar71xx: WNR1000v2: fix for random WLAN MAC
Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3
and WNR612v2.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 49051
2016-03-20 14:41:58 +00:00
John Crispin
4d6c4994fc ar71xx: Use PHY fixups for Open Mesh MR1750
The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.

This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.

Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49031
2016-03-16 09:27:14 +00:00
John Crispin
ebcce35be4 ar71xx: Use PHY fixups for Open Mesh MR900
The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.

This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.

Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49030
2016-03-16 09:27:11 +00:00
John Crispin
22c5f96c6b ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x
Some u-boot versions for QCA955x change the delays based on the link speed
during boot. This usually breaks the support of other linkspeeds when
OpenWrt is booted. It also conflicts with the
at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own
values in QCA955X_GMAC_REG_ETH_CFG.

The default RGMII values from the Atheros u-boot are currently used to
preset the existing mach files. These may have to be adjusted for boards
using different values but which are not currently set them explicitely in
OpenWrt.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Christian Beier <cb@shoutrlabs.com>
Cc: Chris R Blake <chrisrblake93@gmail.com>
Cc: Benjamin Berg <benjamin@sipsolutions.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Dirk Neukirchen <dirkneukirchen@web.de>
Cc: Christian Mehlis <christian@m3hlis.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 49029
2016-03-16 09:27:08 +00:00
John Crispin
be68f34708 ar71xx: Clear bits in ath79_setup_qca955x_eth_cfg
Some u-boot versions for QCA955x set currently not cleared bits depending
on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c
file is responsible to select the correct configuration bits and thus the
ath79_setup_qca955x_eth_cfg has to clear the unset.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49028
2016-03-16 09:27:04 +00:00
John Crispin
3fd98db818 ar71xx: Add support for the OMYlink OMY-X1
This patch adds support for the OMYlink OMY-X1

https://wiki.openwrt.org/toh/omylink/omy-x1

http://www.omylink.com/

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49026
2016-03-16 09:26:58 +00:00
John Crispin
05d73a2a73 ar71xx: Arduino Yun board 'WLAN RST' button support
This patch adds support for Arduino Yun board "WLAN RST" button.

Signed-off-by: Hirokazu MORIKAWA <morikw2@gmail.com>

SVN-Revision: 48983
2016-03-10 19:11:13 +00:00
John Crispin
346b1905fb ar71xx: add support for the Telldus TellStick ZNet Lite
Signed-off-by: Micke Prag <micke.prag@telldus.se>

SVN-Revision: 48977
2016-03-10 19:07:26 +00:00
Felix Fietkau
4802f611cb ar71xx: fix qca956x ethernet initialization
Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 48937
2016-03-07 08:45:01 +00:00
Felix Fietkau
3f971c0dc8 ar71xx: WNR612v2: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48924
2016-03-05 09:45:15 +00:00
Felix Fietkau
53b3872ddf ar71xx: WNR2000v3: enable control of all LEDs and buttons
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48922
2016-03-05 09:45:06 +00:00
Felix Fietkau
6bece706ec mac80211: ath9k: enable GPIO buttons
Enable platform-defined GPIO button support for ath9k device.
Key poller is activated for attached platform buttons.
Requires ath9k GPIO chip access.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48921
2016-03-05 09:45:03 +00:00
Felix Fietkau
a8c15c0204 mac80211: ath9k: enable platform WLAN LED name
Enable platform-supplied WLAN LED name for ath9k device.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 48879
2016-03-02 13:22:40 +00:00
Felix Fietkau
5be9e97a82 ar71xx: WNR612v2: fix for random WLAN MAC
Fix for invalid/random WLAN MAC address in WNR612v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48779
2016-02-25 13:31:38 +00:00
Felix Fietkau
3964ac919a ar71xx: WNR2000v3: fix for random WLAN MAC
Fix for invalid/random WLAN MAC address in WNR2000v3. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>

SVN-Revision: 48777
2016-02-25 13:31:32 +00:00
John Crispin
cede06cebc ar71xx: Support for Ubiquiti UniFi AP AC LITE
Add support for the Ubiquiti UniFi AP AC LITE
Signed-off-by: P.Wassi <p.wassi at gmx.at>

SVN-Revision: 48711
2016-02-12 08:31:32 +00:00
John Crispin
13a85914ae ar71xx: Make code formatting consistent on ath79/machtypes.h
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 48706
2016-02-12 08:30:38 +00:00
John Crispin
d6cb792d21 ar71xx: Added support for TL-WA801NDv3
Signed-off-by: Tiziano Bacocco <tizbac2@gmail.com>

SVN-Revision: 48705
2016-02-12 08:30:28 +00:00
Felix Fietkau
b1431170ee ar71xx: register only the built-in switch MDIO bus, hook up eth0 to it, should hopefully fix regression reported in #21520
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48652
2016-02-07 21:00:11 +00:00
Felix Fietkau
a63fd6faf7 ar71xx: fix MDIO bus probe on QCA956x
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48651
2016-02-07 21:00:01 +00:00
Felix Fietkau
a5dd378a0e ar71xx: fold patch 622-MIPS-ath79-add-support-for-QCA956x-ethernet.patch into files/
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48650
2016-02-07 20:59:51 +00:00
Felix Fietkau
2530640f07 ar71xx: add support for linux 4.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48563
2016-01-30 13:19:53 +00:00
Felix Fietkau
e5b5cce442 ar71xx: fix a few include errors
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48562
2016-01-30 13:19:37 +00:00
John Crispin
9d4e076966 ar71xx: fix AR8337 switch initialization on dLAN pro 1200+ WiFi ac
unswap ports 0/6 (broken by 17b8dcd63100a6b9e35199882f38bdc2be640777)

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 48357
2016-01-19 10:16:11 +00:00
John Crispin
ed72c5f846 ar71xx: add support for Netgear WPN824N
Add support for Netgear WPN824N.
Hardware specs:
  * AR7240, 4 LAN ports, 1 WAN port
  * AR9285 WLAN
  * 32 MB RAM
  * 4 MB Flash
  * 16 LEDs (LAN, WAN and Power/Status contain two LEDs for dual color
    effect)
  * 3 Buttons (not supported)

Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>

SVN-Revision: 48356
2016-01-19 10:16:04 +00:00
Felix Fietkau
826cfa5773 ar71xx: fix ap152 support
- ethernet gigabit pll
- switch configuration
- sysupgrade

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 48187
2016-01-10 17:19:34 +00:00
John Crispin
9242d27b4a V2 ar71xx : Add Support for the Bitmain Antrouter R1
This patch adds support for the Bitmain Antrouter R1

http://wiki.openwrt.org/toh/bitmain/r1

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 48058
2016-01-01 21:21:13 +00:00
John Crispin
772f9d4e32 ar71xx: Add support for AirTight Networks C-55
This patch is to add support for the AirTight Networks C-55 Access Point

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47973
2015-12-23 14:43:35 +00:00
Felix Fietkau
814d70b2fd ar8216: rework/fix AR8337 MAC swap handling
In r45970 the MAC swap handling was made opt-in, however some boards
have been forgotten during the conversion. Since the reference design
uses this MAC swapping, and pretty much all known boards using this chip
seem to do so too, enabling the swapping is a more reasonable default
than leaving it disabled.

Change the code to still allow boards to opt-out of this.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47956
2015-12-20 14:25:45 +00:00
Felix Fietkau
3fa85af5ad ar71xx: Add ath79_register_m25p80_large to support >16MB SPI chips
The following patch is to add ath79_register_m25p80_large, which sets
is_flash to false to support bit banging. This is needed on some 32MB+
SPI chips, such as the S25FL256S1

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47952
2015-12-19 11:32:20 +00:00
Felix Fietkau
3f184882e8 ar71xx: Kernel board definition for PowerCloud CR5000
Kernel part of support for the PowerCloud Systems CR5000.  The
    CR5000 is a dual-band 802.11n wireless router with 8MB flash,
    64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
    port gigabit ethernet switch.  The CR5000 was sold as hardware for
    the Skydog cloud-managed router service.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47940
2015-12-19 11:27:32 +00:00
Felix Fietkau
eef3b7acfb ar71xx: Kernel board definition for PowerCloud CR3000
Kernel part of support for PowerCloud CR3000.  The CR3000 is
    a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
    a four port fast ethernet switch, and a fast ethernet wan port which
    was sold by PowerCloud Systems as hardware for the Skydog
    cloud-managed router service.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47939
2015-12-19 11:27:25 +00:00
Felix Fietkau
4cc541756d ar71xx: Kernel board definition for PowerCloud CAP324
Kernel part of support for PowerCloud CAP324 Cloud AP.
    The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for
    the CloudCommand service for 'cloud' based managment of large numbers
    access points.

    The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
    and 128MB RAM and single gigabit ethernet port.  It can be powered via PoE
    or a power adaptor.

Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>

SVN-Revision: 47938
2015-12-19 11:27:19 +00:00
John Crispin
1f71f2220d ar71xx: add support for TRENDnet TEW-823DRU
Add support for TRENDnet TEW-823DRU:
- cpu: QCA9558 @720MHz
- flash: 16MB
- ram: 256MB
- 4+1 RJ45 100/1000Mbps
- wifi:  QCA9558 (bgn) and QCA9880-BR4A (ac)
- 1x USB 2.0

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 47927
2015-12-17 09:30:05 +00:00
John Crispin
abc84551c0 ar71xx: add support for Cisco's MR18
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>

Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>

SVN-Revision: 47878
2015-12-12 06:42:29 +00:00
Felix Fietkau
0b6271faf4 ar71xx: reorganize target patches/files to make it possible to add boards without adding patch files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47874
2015-12-11 21:12:14 +00:00
Felix Fietkau
0186d4c2c2 ar71xx: on wnr2200, revert the mac0/mac1, the ethernet interfaces are swapped. use MAC1 for wlan
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47873
2015-12-11 21:12:04 +00:00
Felix Fietkau
6e12ef7430 ar71xx: fix MAC address swapping on WNR2200 and fix the WLAN MAC address
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47871
2015-12-11 19:21:59 +00:00
John Crispin
eb8ff56684 ar71xx: Add support for Wallys DR344
This patch is for Wallys DR344 support under OpenWRT

Signed-off-by: Philippe Duchein <wireless-dev@duchein.net>

SVN-Revision: 47847
2015-12-11 15:04:47 +00:00
John Crispin
1a092ce0e0 ar71xx: add GL-Domino Pi support V3
This is the patch for GL-Domino Pi V3. Updated against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47622
2015-11-24 18:30:50 +00:00
John Crispin
a04c3e73a3 ar71xx: add GL-AR300 support V3
This is the patch for GL-AR300 V3, tested against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47621
2015-11-24 18:30:19 +00:00
John Crispin
72093bd528 ar71xx: add GL-AR150 support V3
This is the 3rd version. Modified against the latest trunk.

Signed-off-by: alzhao<alzhao@gmail.com>

SVN-Revision: 47620
2015-11-24 18:29:59 +00:00
John Crispin
99fd9a7041 ar71xx: add support for the devolo dLAN Hotspot
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 47554
2015-11-21 21:24:18 +00:00
Hauke Mehrtens
fa137d51f5 ar71xx: add Arduino Yun
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
7e2976fa83

The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.

Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 47451
2015-11-10 23:13:09 +00:00
Felix Fietkau
7f75961e38 ar71xx: add support for TP-LINK TL-WR941ND v6 (international version)
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.

This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 47420
2015-11-08 20:39:18 +00:00
Felix Fietkau
ae7e7239b8 ar71xx: Add support for ZyXEL NBG6616.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>

SVN-Revision: 47405
2015-11-07 12:51:39 +00:00
John Crispin
632c92094a ar71xx: Bitmain Antminer S1/S3 set GPIO for USB Power
Antminers using the stock bootloader will not hash without this GPIO set.
Applies to DD and CC

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 47261
2015-10-26 09:01:28 +00:00
John Crispin
fb152a810c ar71xx: Send power to USB port on WNR2200
This patch fixes ticket #15267 by enabling power on the
WNR2200's USB port. At present, the USB port on the WNR2200
is non-functional due to it not receiving power.

This patch defines an additional GPIO pin, but none of the
current GPIO definitions have been modified.

Signed-off-by: Riley Baird <BM-2cVqnDuYbAU5do2DfJTrN7ZbAJ246S4XiX@bitmessage.ch>

SVN-Revision: 47236
2015-10-19 18:18:12 +00:00
John Crispin
8d8a937272 ar71xx: Add Gainstrong MiniBox v1.0 support to trunk
This patch supersedes the v1 from September 17th.

Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.

The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).

Fixed items:

- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.

Compiles fine, has been confirmed working by owners on 15.05.

Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?

Thank you

Signed-off by: Stijn Segers <francesco.borromini@inventati.org>

SVN-Revision: 47234
2015-10-19 17:55:25 +00:00
John Crispin
257e76a3df ar71xx: Bitmain Antminer S1 & S3 cleanup
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 47221
2015-10-19 10:10:02 +00:00
Felix Fietkau
896d3e3e13 ar71xx: Add WeIO Board Support
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.

Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]

SVN-Revision: 47036
2015-09-24 09:08:47 +00:00
John Crispin
ac75fc8d98 ar71xx: add support for ap152 reference board
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46972
2015-09-16 08:33:14 +00:00
John Crispin
f6607a4bec ath79: dev-eth: fix QCA9561 set phy interface mode and mask
QCA9563 and QCA9561 are two series of Qualcomm SoC Dragonfly. The only different
is QCA9563 w/o internal switch. It has one GMAC with SGMII interface. But they
have the same device ID(0x1150). So they share the same codes.

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46971
2015-09-16 08:33:04 +00:00
John Crispin
0dbced8a48 ar71xx: add TP-LINK TL-WDR3320 v2 support
This patch adds support for TP-LINK TL-WDR3320 v2.

This router uses a chinese version 2 firmware header,.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 46934
2015-09-14 20:12:16 +00:00
John Crispin
aba20334a4 ar71xx: add kernel support for the OpenMesh MR1750 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46926
2015-09-14 20:10:43 +00:00
Felix Fietkau
2ce833060a target: ar71xx: add support for COMFAST CF-E316N v2 board
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 46852
2015-09-11 16:31:35 +00:00
John Crispin
af60c367b7 ar71xx: add support for TP-Link TL-WDR6500 v2
Signed-off-by: Weijie Gao <hackpascal@gmail.com>

This patch adds support for TP-Link TL-WDR6500 v2.

The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.

SVN-Revision: 46663
2015-08-17 06:24:04 +00:00
John Crispin
4463bc017b ar71xx: Add support for Black Swift
Add support for the Black Swift board:
http://www.black-swift.com/

Took relevant parts and slightly adapted from:
https://github.com/blackswift/openwrt/blob/master/bsb.patch

Signed-off-by: Bruno Randolf <br1@einfach.org>

SVN-Revision: 46651
2015-08-17 06:16:54 +00:00
John Crispin
5cd49bb067 ar71xx: add support for Onion Omega
This patch adds support for the Onion Omega.

https://onion.io/omega

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>

SVN-Revision: 46458
2015-07-24 09:09:49 +00:00
John Crispin
b98205c946 ar71xx: Add support for AP147-010 reference board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46457
2015-07-24 09:09:42 +00:00
Felix Fietkau
d26e8d9439 Revert "ar71xx: Add support for Cisco-Linksys WAP4410N" (r46250)
The commit is incomplete, it does not even build the mach-* file

This reverts commit 6e6adcf7a197b1802cb728ddcccf05f890ca0574

SVN-Revision: 46425
2015-07-19 17:58:27 +00:00
John Crispin
1eccdb4fd4 ar71xx: add support for the devolo dLAN pro 1200+ WiFi ac
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 46342
2015-07-14 07:37:03 +00:00
John Crispin
02984a6e09 ar71xx: add support for the devolo dLAN pro 500 Wireless+
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 46338
2015-07-14 07:32:33 +00:00
John Crispin
e8161f4764 ar71xx: compex wpe72 add space to include statement
Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46284
2015-07-09 07:04:14 +00:00
John Crispin
8a1cca04ca ar71xx: compex wpj531 register usb support
Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46283
2015-07-09 07:03:54 +00:00
John Crispin
3802ce01a9 ar71xx: compex wpj531 fix setting mac address on ethernet
Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46282
2015-07-09 07:01:55 +00:00
John Crispin
4b28adc066 ar71xx: compex wpj531 fix ethernet registration
In fb6f62e97733312053ab593fcf68eea47a21169e several settings
are set on the ethernet device, but they are not working.

Fix Ethernet by setting the right values.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46281
2015-07-09 06:59:18 +00:00
John Crispin
08790c5ee8 ar71xx: Add support for Cisco-Linksys WAP4410N
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.

Signed-off-by: Ryan A Young <rayoung@utexas.edu>

SVN-Revision: 46250
2015-07-07 18:06:39 +00:00
John Crispin
d535218230 ar71xx: add support for D-Link DIR-615 rev. Ix board
Based on trunk r46212.

Signed-off-by: Jaehoon You <teslamint@gmail.com>

SVN-Revision: 46248
2015-07-07 13:48:39 +00:00
John Crispin
f7ffbbc5fc ar71xx: Use *_eth_cfg helper for Open Mesh MR900 boards
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46241
2015-07-07 13:47:39 +00:00
John Crispin
055663201b ar71xx: Add Support for the Bitmain Antminer S3
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner

http://wiki.openwrt.org/toh/bitmain/s3

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46236
2015-07-07 13:46:54 +00:00
John Crispin
9f2b8b3902 ar71xx: allow pci calibration fixup to work with ar9344
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 46235
2015-07-07 13:46:44 +00:00
Felix Fietkau
b26077026f ar71xx: add support for ap143
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46208
2015-07-07 08:06:05 +00:00
Felix Fietkau
c9e433206f ar71xx: rework patch for qca953x/956x
Patch cherry-picked from the following location:
https://www.codeaurora.org/cgit/quic/qsdk/oss/system/openwrt/commit/?h=release/coconut_ioe4531_2.0&id=5c357bf6c763e4140dddcc9a3bc5f005525a9c0e

Changelist,
    - add more register defines
    - add EHCI support
    - fix GPIO pin count to 18
    - fix chained irq disabled
    - fix GMAC0/GMAC1 initial
    - fix WMAC irq number to 47
    - merge the changes of dev-eth.c from the patch to file.

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 46207
2015-07-07 08:05:55 +00:00
Felix Fietkau
7acbd52055 ar71xx: fix ethernet initialization on QCA953x-based boards (TP-Link TL-WR841N/ND v9, Compex WPJ531)
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 46206
2015-07-07 08:05:50 +00:00
John Crispin
be755a99d6 ar71xx: add kernel support for EnGenius EPG5000.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>

SVN-Revision: 46047
2015-06-18 18:21:33 +00:00
John Crispin
e85f3471ba ar71xx: add support for TL-WR720N-v4.
The hardware should be almost the same as TL-WR720N-v3.  WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>".  Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 46046
2015-06-18 18:21:23 +00:00
John Crispin
8399be545a ar71xx: add support for compex wpj531
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj531-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46045
2015-06-18 18:21:15 +00:00
John Crispin
694dd581eb ar71xx: Add Support for the Bitmain Antminer S1
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner

http://wiki.openwrt.org/toh/bitmain/s1

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>

SVN-Revision: 46044
2015-06-18 18:21:05 +00:00
Felix Fietkau
4a9d726200 ar8216: Fix problem with AR8337 MAC swap handling
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.

Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.

The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 45970
2015-06-14 17:43:50 +00:00
Felix Fietkau
28d8972c25 ar71xx: fix 100/10mbps ethernet link issues on mynet range extender
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.

The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.

The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.

Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 45954
2015-06-14 17:41:01 +00:00
John Crispin
66950455b7 ar71xx: Add support for the Meraki MR12 & MR16
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.

Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>

SVN-Revision: 45726
2015-05-23 15:27:22 +00:00
Luka Perkov
2a9ebfb503 ar71xx: add status led found on ew-dorin boards
Signed-off-by: Catrinel Catrinescu <cc@80211.de>

SVN-Revision: 45656
2015-05-10 07:47:04 +00:00