In order to support the various board NAND layout that we support, introduce a
sub-profile similar to the one used by ar71xx.
These subprofiles provide a default implementation for most of the building
functions, while allowing each sub-profile to override any of these operations
in order to have a more specific behaviour, like Mamba expects for example.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44261
Some devices out there only have a NOR flash to store the rootfs on.
While using UBI is arguable on this kind of flash, this is something that should
be supported.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44260
We're going to need the MTD split related options for our NOR support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44259
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44255
The ubootloader of the M2M sets the reset bits for
both USB device and USB host during initialization
(to save a few mA of power during boot).
However, for the usb<->sata bridge to be properly
detected, it is necessary to clear both reset bits
as otherwise the kernel logs will just be filled
with:
usb 1-1: device descriptor read/64, error -145
...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44248
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
- budget is decremented with completed frames, so don't check if done is
smaller
- ACK the interrupt before processing further frames to fix a small race
condition.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44234
It fails to build because of missing of_irq_parse_raw and incompatible
irq_create_of_mapping.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44230
Replace the now defunct 062-mips_decompressor_build_fix.patch with another
patch that simply undefines the arch memset and memcpy defines to avoid
syntax errors in the redeclaration.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44223
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
Fix the WLAN MAC address to match the one printed on the label by using the
correct address from the ART instead of the address of the LAN interface.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44183
The mac address usually write in factory block. but sometime user erase this block , the mac address will change to ff:ff:ff:ff:ff:ff.
This patch is purpose to fix this issue.
Signed-off-by: wengbj <linux.c@foxmail.com>
SVN-Revision: 44166
This patch adds an entry in the uci-defaults' led-file to configure the
WAN and WLAN LEDs by default.
Signed-off-by: Vincent Wiemann <me@bibbl.com>
SVN-Revision: 44165
Changeset r43049 removed the "062-mips_decompressor_build_fix.patch" which is
still required to properly build the xburst kernel.
Fix the syntax error in the preprocessed code by explicitely undefining the
"memcpy" and "memset" macros prior to declaring the replacements functions.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44133
Using port-based VLANs depends on a non-standard
swconfig parameter, which compilcates things like
LuCI that don't know about it. This patch changes
the default to use 802.1q VLANs internally in the
switch, but without tagging packets since we have
two Ethernet ports.
iperf3 tests indicate no difference in performance
versus port-based VLANs when the CPU port is not
using tags.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 44122
* fix TSO features verify on mt7621 firewrt board
* improve tx clean up. no need to access uncached
memory. also use TX_DTX register instead of
read tx ring DONE bit
* mt7621 need napi weight 64 to get more performance
* remove netif_receive_skb, after kernel version
3.7 tcp4_gro_receive can handle tcp checksum.
on rt2880 use iperf tcp LAN to WAN throughput test.
with gro 135 Mbits/sec. without gro 80.4Mbits/sec.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44118
on mt7621 don't have tx vlan vid registers.
so set FE_REG_FE_DMA_VID_BASE to 0.
set rx vlan offload register to disable.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44117
the rx_buf_size now is 1534 when mtu is 1500.
the ethernet frame with vlan tag and FCS is 1522.
so the buffer is enough.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44116
Add global read-only swconfig attribute "arl_table" to display the
address resolution table.
So far the chip-specific part is implemented for AR8327/AR8337 only
as I don't have the datasheets for the other AR8XXX chips.
Successfully tested on TL-WDR4300 (AR8327rev2)
and TL-WDR4900 (AR8327rev4).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44104
Until a few years ago the page switch wait time was set to msleep(1)
what was changed to usleep_range(1000, 2000) later.
I can not imagine that a low-level operation like switching page
on register level takes so much time.
Most likely the value of 1ms was initially set to check whether
it fixes an issue and then remained w/o further checking whether
also a smaller value would be sufficient.
Now the wait time is set to 5us and I successfully tested this on
AR8327. IMHO 5us should be plenty of time for all supported chips.
However I couldn't test this due to missing hardware.
If other chips should need a longer wait time we can add the
wait time as a parameter to the ar8xxx_chip struct.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44103
Check for switch port link changes and
- flush ATU in case of a change
- report link change via syslog
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44102
The functionality to flush the address translation table contains two bugs
which luckily compensate each other.
1. Just setting the operation is not sufficient to perform the flushing.
The "active" bit needs to be set to actually trigger an action.
For the vtu operations this is implemented correctly.
2. ar8xxx_phy_read_status is called every 2s by the phy state machine
to check for link changes. This would have caused an ATU flush
every 2s.
Fix the chip-specific ATU flush functions and remove the ATU flush call
from ar8xxx_phy_read_status.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44101
TP-LINK TL-WR843ND v1 is the same model like wr41, but with
Power over Ethernet on wan port.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 44085
This adds a patch to target/linux/lantiq/patches-3.14
fixing a bug clock code on ar9. The current version returns
the wrong value for the fpi clock frequency in some
cases.
See discussion for further details:
https://lists.openwrt.org/pipermail/openwrt-devel/2015-January/030688.html
I'm not sure about the patch naming and numbering convention.
Do please let me know it this is not OK.
Many thanks,
Ben Mulvihill
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 44083
the GPIO controlling the rf filter is not configured properly by this patch.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44077
This patch is a follow up for my previous patch:
"ramips: add support for Intenso Memory 2 Move USB 3.0".
It fixes a couple of errors in the DTS (one of which broke
the gpio-buttons). The kmod-leds-gpio dependency has been
dropped as it is already part of the ramips target.
Furthermore the ramdisk/uImage image is generated by default
for the rt3050 subtarget. This image is needed to flash
OpenWrt for the first time onto the device via TFTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44072
The dLAN USB Extender profile was referecing binary packages which are not to
be included in any of the source-only feeds. Instead remove these references
and document how to use the 3rd party feed.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 44071
Ths will allow us to use early 3xx numbers for patches designed for
sending mainline.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44057
* use default timeout value
* print more debug ring info
* move timeout reset function to workqueue
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44043
This patch builds on the previous three to streamline support for the
Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44032
It seems the call to ltq_get_eth_mac() disappeared at some point. This
patch puts it where it currently most makes sense.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44031
Somewhere in the conversion of the MIPS architecture code to Device Tree
usage, there's been a failure to keep the separate variables holding the
kernel command line reconciled between the tree and the bootloader. This
patch restores previous functionality that broke.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44030
Currently this initscript fails if the macaddr has any leading zeroes.
This patch corrects the problem.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44029
The swconfig get_link attribute (at least) on AR8327/AR8337 doesn't
consider the autonegotiated flow control.
AR8327/AR8337 provide the info about autonegotiated rx/tx flow control
in bits 10 and 11 of the port status register.
Use these values to display info about autonegotiated rx/tx flow
control as part of the get_link attribute.
Successfully tested on TL-WDR4900 (AR8327 rev.4) and
TL-WDR4300 (AR8327 rev.2).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44023
AR8327/AR8337 allow to read the result of EEE autonegotiation.
If EEE is autonegotiated between the link partners, display
this as part of the swconfig get_link attribute.
eee100: 100MBit EEE supported by both link partners
eee1000: 1GBit EEE supported by both link partners
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44022
Users reported network issues with AR8327 which turned out to be caused
by EEE not working correctly with certain link partners (ticket 14597).
The workaround was to disable EEE on all ports (changeset 41577).
The issue was with certain link partners only, therefore this patch
allows to control usage of EEE per port via swconfig.
Still the default is to initially disable EEE on all ports.
Successfully tested on a TL-WDR4900 (AR8327 rev.4)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44021
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
The only reason this patch was helping was moving bcma init *after*
of_serial init. It was a bit of luck because both drivers use
device_initcall.
It isn't really a correct way to provide early logging.
Now we have earlyprintk support in bcm53xx we can drop this patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43981
Malta ramdisk images are no longer copied to output due to a recent change.
This change reimplements copying of ramdisk images for Malta builds.
Signed-off-by: Eric Schultz <eschultz@prplfoundation.org>
SVN-Revision: 43970
The mvebu image makefile define something almost identical to the generic
implementation found in include/image.mk.
Switch to this implementation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SVN-Revision: 43969
The mvebu image Makefile directly calls the padjffs2 utility, while there's an
generic make function to do just that. Switch to it
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SVN-Revision: 43968
Since the driver doesn't know anything about (M)STP
we just hard-set the ports to be enabled if they are
part of the VLAN.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43938
- eliminate MV_CPUPORT; not necessary since we define
the CPU port(s) via Device Tree
- add STU and expand VTU operations
- update register names to match those of 88E61xx rather than
mvswitch's 88E6060
- use more consistent formatting
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43937
3.3 produced *.dtb files in arch/arm/boot/ while 3.14 will produce those
in arch/arm/boot/dts/, adjust the image makefile accordingly.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43925
Most of the devices we support have between 16MiB and 32MiB of RAM
available.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43924
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43883
This patch fixes a wrong mask operation for the rt2880-compatible ralink devices.
The mask operation reads the actual flags and then logical combines it with the pin flag it want to set.
Unfortunally, for rising as for falling interrupt flags the actual flag status of the rising interrupts was used.
That caused a problem if you want to use more than one falling GPIO interrupt.
Now the correct (seperated) actual status is used for both, falling and rising.
Signed-off-by: Jonas Arndt <info@greenwire-elektronik.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43882
Move all AR8327/AR8337-specific driver code into a separate source file
ar8327.c and adjust patches so that ar8327.c is compiled if
CONFIG_AR8216_PHY is set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43845
Move several structure definitions and #defines from ar8216.c
to ar8216.h and move AR8327/AR8337 header stuff into a new
header file ar8327.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43844
modules build during the kernel compile phase are ignored anyway,
all modules should be built using KernelPackage in
package/kernel/linux/modules/*
selecting the appropriate config symbols there rather than in
target/linux/*/config-*
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43842
The following patches unfortunately didn't hit the kernel stable
branches yet, therefore cherrypicking them for OpenWRT here:
* bridge: fix netfilter/NF_BR_LOCAL_OUT for own, locally generated queries
* bridge: multicast: enable snooping on general queries only
* bridge: multicast: add sanity check for general query destination
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
SVN-Revision: 43841
This will allow simple sysupgrade-s including simpler reverting to the
original firmware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43799
After the changes make ubinize.cfg optional in image.mk, ubifs
generation can now safely be enabled again.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43789
kernel lock debugging unveiled that we should not call
of_reset_control_get inside a clock's enable operation (see below)
move of_reset_control_* previously used in pllb_clk_enable to new
pllb_clk_prepare and pllb_clk_unprepare functions.
use a container to carry runtime information.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2742 lockdep_trace_alloc+0xb8/0xfc()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.26 #6
[<c001a6ac>] (unwind_backtrace) from [<c0016dec>] (show_stack+0x10/0x14)
[<c0016dec>] (show_stack) from [<c0194f68>] (dump_stack+0x7c/0x94)
[<c0194f68>] (dump_stack) from [<c0021b50>] (warn_slowpath_common+0x68/0x8c)
[<c0021b50>] (warn_slowpath_common) from [<c0021ba4>] (warn_slowpath_fmt+0x30/0x40)
[<c0021ba4>] (warn_slowpath_fmt) from [<c0061b30>] (lockdep_trace_alloc+0xb8/0xfc)
[<c0061b30>] (lockdep_trace_alloc) from [<c00cb740>] (kmem_cache_alloc+0x1c/0xf8)
[<c00cb740>] (kmem_cache_alloc) from [<c01d33c8>] (of_reset_control_get+0xe8/0x12c)
[<c01d33c8>] (of_reset_control_get) from [<c0269228>] (pllb_clk_enable+0x14/0xbc)
[<c0269228>] (pllb_clk_enable) from [<c0265738>] (__clk_enable+0x54/0xa0)
[<c0265738>] (__clk_enable) from [<c0265acc>] (clk_enable+0x18/0x2c)
[<c0265acc>] (clk_enable) from [<c04325f8>] (oxnas_pcie_probe+0x3b8/0x6a0)
[<c04325f8>] (oxnas_pcie_probe) from [<c01f2510>] (platform_drv_probe+0x18/0x48)
[<c01f2510>] (platform_drv_probe) from [<c01f1070>] (driver_probe_device+0xd8/0x24c)
[<c01f1070>] (driver_probe_device) from [<c01f1298>] (__driver_attach+0x70/0x94)
[<c01f1298>] (__driver_attach) from [<c01ef728>] (bus_for_each_dev+0x4c/0x98)
[<c01ef728>] (bus_for_each_dev) from [<c01f0818>] (bus_add_driver+0xcc/0x1e8)
[<c01f0818>] (bus_add_driver) from [<c01f169c>] (driver_register+0xa0/0xe8)
[<c01f169c>] (driver_register) from [<c01f2568>] (platform_driver_probe+0x20/0xa4)
[<c01f2568>] (platform_driver_probe) from [<c0013a3c>] (do_one_initcall+0x90/0x140)
[<c0013a3c>] (do_one_initcall) from [<c0421d38>] (kernel_init_freeable+0x1e4/0x2c0)
[<c0421d38>] (kernel_init_freeable) from [<c000c214>] (kernel_init+0x8/0x104)
[<c000c214>] (kernel_init) from [<c0008768>] (ret_from_fork+0x14/0x2c)
---[ end trace 5f17ed2f61e0683f ]---
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43787
accidentally #if was used instead of #ifdef, thus gcc warned
about CONFIG_ATA_LEDS being undefined...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43786
This is a 3.14.x backport of:
"mvneta: Fix TSO and checksum for non-acceleration vlan traffic"
Upstream commits:
817dbfa5d1bc276a72c1a577310382008e8aca0a
2d39d120781a5770573dc6ed672a5a562f541aea
Fixes vlan tagging on SoC interfaces for the WRT1900AC. Useful
when using mvsw6171 driver.
Signed-off-by: Mark Milburn <mark.a.milburn@gmail.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43781
safed one level of indention by using 'continue' instead of a
lengthy if-clause.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: use logic-AND instead of '?' operator when checking for hw bug 6320
SVN-Revision: 43768
- replaced // comments by /* comments */
- added line-breaks where needed
- fixed white-space according to kernel style
- fixed some obvious spelling mistakes in comments and printks
- removed some unneeded left-overs imported from vendor code-base
- replaced printk(...) by libata macros where possible
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43767
locking for 2nd port and hwraid was added from vendor's GPL code which
doesn't comply with current kernel coding style.
- moved all global variables into host_priv
- renamed locks
- sanetized acquire() and release() parameter list
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43766
and no longer compile-in ext4 filesystem now that sata_oxnas is
also built as a module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43765
Set defaults health led to a timer heartbeet (200/800)
and populate network for:
- GuruplugServerPlus
- SheevaPlug
- SheevaPlug with eSATA
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
SVN-Revision: 43752
This maps the LAN ports to eth0 and WAN port to eth1.
Since there are two interfaces the 802.1q VLAN mode
is unnecessary and left disabled. Port-based VLANs
are used instead.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43750
When there is no device connected to the controller we should not start
the controller. This also changes between PCIe 1.0 and PCIe 2.0 speed
based on the device. This code is based on code from the new Broadcom
PCIe controller driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43748
This patch adds soc support for QCA9561 and TP9343.
TP9343 is a reduced version of QCA9561, which can be found in TP-LINK routers in China.
The qca956x_wmac has not yet been supported by ath9k.
tested on TL-WDR6500 and TL-WR882N v1 (Chinese version)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 43744
Remove read/write/rmw member functions from ar8xxx_priv
There seems to be no real benefit of the ar8xxx_priv member functions
read/write/rmw as one implementation exists for each of them only.
Especially ar8xxx_mii_rmw is assigned to priv->rmw first and then
mapped to ar8xxx_rmw.
Rename the ar8xxx_mii_.. functions to ar8xxx_.. and use them directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43742
Create helpers mii_read32 / mii_write32 for 32 bit MII ops.
Rename r3 variable to page in ar8xxx_mii_write to make it consistent
with the other ar8xxx_mii_xxxx functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43741
Factor out chip-specific parameters from ar8xxx_probe_switch.
Move the ar8xxx_chip definitions after the swops definitions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43740
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
This will allow us to drop it in the future. This patch doesn't change
the final mtdpart.c, it remains the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43696
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
It moves firmware patch code behind an extra check on board_name.
Otherwise it will calculate firmware checksum for unaffected boards.
It also reduce boottime by a md5 calculation and removes error message
on boot if firmware not found.
SVN-Revision: 43679
Restoring the config for kernel 3.14 didn't contain that change already
made to config-3.18.
It is needed to make squashfs in the kernel match the compression settings
for ARCH=arm in the framework.
If set to ARMTHUMB, boot fails due to squashfs being unreadable if the
filesystem was generated for wth ARM BCJ filter.
in include/image.mk: BCJ_FILTER:=-Xbcj $(LINUX_KARCH)
Thus the ARM filter is used for all ARM targets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43640
it should needs to depend on imx and mxs
also remove duplicate kmod definition from mxs target
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43627
The target au1000 has at least 2 different models, the
'InternetBox' and the 'MeshCube' which look very similar
from the kernel point of view but are totally different
devices which base on the same design. Populating /tmp/sysinfo
now. The 1st one has an issue which leads to a random
mac-address after each boot which is corrected now via
reading the bootloader-env. The real fix would be
converting to DTS, this is only a workaround now.
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 43626
This is required because it has to be called at very precise moment. See
comment in driver for details.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43611
similar to mv_sata, use nr-ports attribute from device tree.
import and adapt locking code from vendor GPL sources.
add dma controller handling, it may be used in future to avoid
full core resets similar to the vendor SDK's "progressive cleanup"
function.
this is still very dirty and aimed to first of all do things
quite exactly like the reference code. and it somehow works.
obviously there is lots of room for improvement :)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43598
sata_oxnas.c is obviously a refactored version of sata_ox820.c
which does contain this header.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43597
According to the vendor tarball, the TD-w8900GB's flash has 64k erase
block size, but CFE spans two blocks. So fixup the image offset
accordingly but keep block size at its default (64k).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: add commit message, add image offset, change nvram offset]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43572
This adds some updates to the NAND driver and refreshed the config.
Most of these changes are done in preparation for mainling it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43546
This adds some updates to the PCIe driver and refreshed the config.
Most of these changes are done in preparation for mainling it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43545
This brings ssb and bcma to wireless-testing tag master-2014-12-05
In addition it also adds the ARM-BCM5301X-Add-IRQs-to-Broadcom-s-bus-
axi-in-DTS-f.patch which adds the irq number in a way it is done in the
mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43544
I don't see that we're in an atomic context so there's no need to
busy-wait. Therefore replace the delay with sleep calls.
See also Documentation/timers/timers-howto.txt. It states:
"In general, use of mdelay is discouraged and code should
be refactored to allow for the use of msleep."
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43539
Replace the fixed wait time of 1s with polling for BMCR_RESET
to be cleared on all PHYs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43538
This reverts commit c81ddddde5fd193802d511b42eb7b108aac17136 on
https://gitorious.org/openwrt-oxnas/openwrt-oxnas.git
which removed patches and config for 3.14.
[arm_introduce-dma-fiq-irq-broadcast patch was renamed to match 3.18]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43520