Commit graph

662 commits

Author SHA1 Message Date
Mathias Kresin
91e11bec74 ramips: fix mt7628 eval board pinmux
There is no pinmux group "jtag" for mt7628 and the pinmux driver fails
to load due to the use of the not existing group.

Fixes: FS#1515

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-25 20:33:27 +02:00
Mathias Kresin
e988b0fe0d ramips: mt7620: fix double use of pins
The pins are used as (LED) GPIOs and can't be used at the same time as
hardware controlled ephy (LED) pins.

Fixes: FS#1500

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-17 08:40:56 +02:00
Felix Fietkau
07b4e49abb ramips: fix usb phy compatible string (should fix FS#1489)
In the new USB phy driver, it checks the compatible string before
attempting to iomap its mem resource and do the extra PHY init

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-13 13:13:53 +02:00
Vianney le Clément de Saint-Marcq
bcf2125142 ramips: add support for Zorlik ZL5900V2
The Zorlik ZL5900V2 is an unbranded clone of HAME MPR-A1/2.  It is
marketed as "3G Wi-Fi Router".  Only the PCB has the model name
"ZL5900V2" printed on it.

Specifications:
- Ralink RT5350F (360 MHz)
- 32 MB RAM
- 8 MB Flash
- 802.11bgn 1T1R
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (Type-A)
- 5200 mAh battery

The ramdisk image (not the squashfs sysupgrade image) can be flashed
through the web interface (named "GoAhead") of the factory firmware.
However, as the factory firmware does not cleanly unmount the rootfs
before flashing, the device may hang instead of rebooting after
successful write.  Power cycling the device gets you in OpenWrt where
the squashfs image may be flashed through normal sysupgrade procedure.

Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
2018-04-08 09:53:50 +02:00
Zheng Qian
80a94aacaf ramips: add support for the YouHua WR1200JS
YouHua tech WR1200JS is an AC1200 router with 5 1Gb ports (4 Lan, 1 Wan)
and 1 USB 2.0 port.

Devices is base on MediaTek MT7621AT + MT7603E + MT7612E.

Specification:

- MT7612AT (880 MHz)
- 128 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 2T2R 2.4 GHz (MT7603E)
- 2T2R 5 GHz (MT7612E)
- 1x USB 2.0
- 10x LED (Power 2G 5G WPS Internet LAN4-1 USB)
- 3x button (reset wifi wps)
- DC jack for main power input (12V)

Installation:

1.) Press reset key 5 sec and restore the factory default
2.) Login webUI and change username to root and set a
    new password
3.) Visit http://192.168.2.254/adm/telnetd.shtml and
    turn on the telnet service
4.) Copy openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin
    to a usb pan
5.) Plug the usb pan to the router, telnet to the router
    and login by root
6.) cd /media/sda1 and check the initramfs file is there
7.) exec command:
    mtd_write write openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin Kernel
8.) reboot and visit 192.168.1.1

Signed-off-by: Zheng Qian <sotux82@gmail.com>
2018-04-08 09:52:48 +02:00
Giuseppe Lippolis
1680ae7eae ramips: add dwr-512 jboot firmware configuration
The previous fw version require the replacement of the stock bootloader
with u-boot. This prevent an easy stock restore of the original fw.

Now a proper fw util has been developed to manage the stock jboot
bootloader. Therefore make sense have a fw image for the stock
bootloader.

The old fw configuration (u-boot) is not compatible with the new one
and will not be supported anymore.

So at the end 2 image can be generated:

1) factory image with jboot bootloader
     openwrt-ramips-rt305x-dwr-512-b-squashfs-factory.bin
2) sysupgrade image with jboot bootloader
     openwrt-ramips-rt305x-dwr-512-b-squashfs-sysupgrade.bin

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2018-04-08 09:51:06 +02:00
Vianney le Clément de Saint-Marcq
eda27d7557 ramips: fix usbphy DT nodes on linux 4.14
The Ralink USB PHY driver merged into mainline has a slightly different
device tree binding than the patch that was used with linux 4.9.
The new driver requires a `ralink,sysctl` node pointing to the `syscon`
node.

This patch also sets `#phy-cells` to 0, as recommended by the mainline
documentation [1].

[1] Documentation/devicetree/bindings/phy/ralink-usb-phy.txt

Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
2018-04-07 17:53:34 +02:00
Piotr Dymacz
10ea53f900 ramips: add U-Boot env support for ALFA Network AC1200RM
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-04-06 23:11:00 +02:00
John Crispin
424a9ae128 ramips: implement hardware NAT offload for MT7621
Supports IPv4 flow offloading on MT7621 for Routing, SNAT and DNAT

Supported are regular ethernet->ethernet connections, including one
802.1q VLAN and/or PPPoE encapsulation

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-06 19:37:53 +02:00
Giuseppe Lippolis
6525bffc0a ramips: add support for DLINK DWR-921-C1
The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.

Specification:

  * MediaTek MT7620N (580 Mhz)
  * 64 MB of RAM
  * 16 MB of FLASH
  * 802.11bgn radio
  * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  * 2x external, detachable (LTE) antennas
  * UART header on PCB (57600 8n1)
  * 6x LED (GPIO-controlled)
  * 1x bi-color Signal Strength LED (GPIO-controlled)
  * 2x button
  * JBOOT bootloader

The status led has been assigned to the dwr-921-c1:green:sigstrength (lte
signal strength) led. At the end of the boot it is switched off and is
available for lte operation. Work correctly also during sysupgrade
operation.

Installation:
Apply factory image via d-link http web-gui.

How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
    blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
    curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2018-04-04 08:42:35 +02:00
INAGAKI Hiroshi
e3bf92edf5 ramips: fix switch and MAC address for WHR-G300N
WHR-G300N has 5 ethernet ports (lan: 4, wan: 1), but there was no
correct configuration in 02_network script and 6 ports was configured
on the switch.
Also, since the MAC address was not acquired from factory partition,
incorrect values was set to LAN and WAN interfaces.

This commit fixes these issues.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-03-23 20:31:49 +01:00
Peter Lundkvist
d13b05741a ramips: add support for TP-Link TL-WR902AC v3
TP-Link TL-WR902AC v3 is a pocket-size dual-band (AC750) router
based on MediaTek MT7628N + MT7650E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet

* MT7650 ac chip isn't not supported by LEDE/OpenWrt at the moment.
  Therefore 5Ghz won' work.

Flash instruction:

The only way to flash LEDE image in TL-WR902AC v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr902ac-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[drop p2led_an pinmux, this pin isn't used as gpio, fix whitespace issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-18 22:22:38 +01:00
Pawel Dembicki
a5bd8de0bd ramips: add support for D-Link DWR-116-A1/2
The DWR-116-A1/2 Wireless Router is based on the MT7620N SoC.

Specification:

  MediaTek MT7620N (580 Mhz)
  32 MB of RAM
  8 MB of FLASH
  802.11bgn radio
  5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  2x external, non-detachable antennas
  UART (J1 in A1, JP1 in A2) header on PCB (57600 8n1)
  6x LED (GPIO-controlled), 2x button
  JBOOT bootloader

Known issues:
WAN LED is drived by uartl tx pin. I decide to use this pin as
uartlite tx pin.

Installation:
Apply factory image via http web-gui.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-03-18 22:22:38 +01:00
Mathias Kresin
d482356322 ramips: mt7620n: add mdio node and disable port4 by default
Revert the changes I applied to aa5014dd1a ("ramips: mt7620n: enable
port 4 as EPHY by default").

The driver expects a node mdio-bus to be present, regardless of the
actual node status. If the node is missing the driver fails to load  with

  mtk_soc_eth 10100000.ethernet: no mdio-bus child node found

Disable port4 by default again. If the port is enabled but not present, a
"invalid port id 4" warning is shown during boot.

Fixes: FS#1428

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-13 20:18:15 +01:00
Giuseppe Lippolis
aa5014dd1a ramips: mt7620n: enable port 4 as EPHY by default
According to the datasheet the mt7620n have a fixed switch configuration
with 5 ephy (10/100) port. No RGMII configuration is possible.

Drop the mdio node as well. Without RGMII, the mdio node doesn't make any
sense

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[drop mdio node, enable port4 by default]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-06 19:49:06 +01:00
Roman Yeryomin
f5984e0a0c ramips: mt7621: add Mediatek AP-MT7621A-V60 EVB support
This board has:
- mt7621 SoC
- 8MB SPI flash
- 128MB RAM
- 5x ethernet ports from internal (SoC) switch
- 1x ethernet port sitting on gmac2 and IC+ phy (not yet supported)
- 3x PCIe slots
- 1x USB 2.0 and 1x USB 3.0
- sound based on wm8960
- SDXC card slot (full size)

First fw write from interactive u-boot menu, interrupt with 2.
After that sysupgrade.

Tested both with 4.9 and 4.14

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-02-24 16:05:28 +01:00
Benjamin Valentin
2d8eeca842 ramips: enable power LED and second uart on GL-MT300N-V2
The device has a second uart accessible via pin headers, so enable it.

There is also a green power led which was not enabled previously.
Enable it too and use it as status LED.

Signed-off-by: Benjamin Valentin <benjamin.valentin@volatiles.de>
2018-02-23 07:54:29 +01:00
Piotr Dymacz
f1c193c27e ramips: add support for ALFA Network AWUSFREE1
ALFA Network AWUSFREE1 is an USB Wi-Fi N300 adapter based on MT7628.

Specification:

- MT7628AN (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (MT7628) with external FEM (RFFM4203)
- 2x detachable antennas (RP-SMA)
- ASIX AX88772 USB to Ethernet bridge (connected with MT7628 PHY0)
- 4x LED (2 driven by GPIO)
- 1x button (reset)
- 1x mini USB for host and main power input
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Power device with reset button pressed and release it after ~5 sec.
2. Setup static IP 192.168.1.2/4 on your PC.
3. Go to 192.168.1.1 in browser and upload "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 23:40:11 +01:00
Roman Yeryomin
6b6dc2b3e3 ramips: mt7621: fix usb init
In 4.14 reg-names is required to identify resources.
Otherwise init fails with:

[    5.900501] xhci-mtk 1e1c0000.xhci: invalid resource
[    5.910499] xhci-mtk: probe of 1e1c0000.xhci failed with error -22

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-02-22 17:25:38 +01:00
INAGAKI Hiroshi
e1d4aa36b0 ramips: add support for Tama W06
Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek
MT7688AN.

Specification:

- MT7688AN (575 MHz)
- 64 MB of RAM (DDR2 SDRAM)
- 16 MB of Flash (SPI)
- 1T1R 2.4 GHz
- 1x 10/100/1000 Mbps Ethernet
- 4x LEDs (GPIO connected: 3), 1x button
- 1x USB 2.0 Type-A (host)
- UART header on PCB (GND, RX, TX, Vcc from RJ45 side)

Flash instruction using sysupgrade image:
1. Connect micro-USB cable for power supply into W06 and turn on the
router
2. Connect to wifi with SSID "tama-*" with password. Complete SSID and
password are listed on the back of the router
3. Access to 192.168.1.1 and login with user name "admin" and password
empty
4. In firmware update(ファームウェア更新) page, click "参照" button
and click "ブラウザー" button to open file browser, select the
sysupgrade image and press OK button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-02-20 19:25:17 +01:00
Mathias Kresin
cb741654e5 ramips: improve GnuBee Personal Cloud Two support
Use the generic board detection for the GnuBee Personal Cloud Two
instead of the target specific one as all recent additions are doing.

Fixup the pinmux to set all pins used as GPIO to the function GPIO.
Request pins where used.

Drop the i2c from the dts. There is nothing connected. While at it fix an
indentation issue and use references instead of duplicating the whole
node path.

Use the same switch config as for the GB-PC1 and drop the led trigger for
the not supported IP1001 phy connected to second rgmii.

Fixes: c60a21532b ("ramips: Add support for the GnuBee Personal Cloud Two")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
George Hopkins
13f9e40602 ramips: add support for D-Link DAP-1522 A1
D-Link DAP-1522 is a wireless bridge/access point with 4 LAN
ports and a dual-band wireless chipset.

Specifications:
- Ralink RT2880
- 32 MB of RAM
- 4 MB of Flash
- 4x 10/100/1000 Mbps Ethernet (RTL8366SR)
- 802.11abgn (RT2850)

Flash Instructions:
1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin
2. Open the web interface and upload the image

Signed-off-by: George Hopkins <george-hopkins@null.net>
2018-02-13 11:18:07 +01:00
Rosen Penev
c60a21532b ramips: Add support for the GnuBee Personal Cloud Two
The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com
It is a low-cost, low-power, network-attached storage device.

Specifications:

- SoC: MediaTek MT7621AT
- RAM: DDR3 512 MB
- Flash: 32 MB
- Six SATA ports for 3.5" Drives
- One SDcard
- One USB 3.0
- Two USB 2.0
- Gigabit Ethernet: Three Ports
- UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
- Three GPIOs available on a pin header

Flash instructions:

The GnuBee Personal Cloud Two ships with libreCMC installed.
libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
As such one can upgrade using the webinterface or sysupgrade.

Das U-Boot has multiple options for recovery or updates including :

- USB
- http
- tftp

Errata:
- While there are three ethernet ports, the third requires support for
  the second GMAC. This will come in kernel 4.14.
- The first hard drive slot has a clearance issue with the two fan
  headers. Workaround is to pull the headers out and connect the pins to
  jumper wires.
- Using this device as a NAS is problematic with the 4.9 kernel as many
  /dev/sdX reads throw silent errors. The current theory behind this is
  some kind of unhandled DMA mapping error in the kernel. This is not an
  issue with kernel 4.4.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-02-13 10:01:52 +01:00
Henryk Heisig
14951e8f8e ramips: add support for TP-Link Archer C50 v3
TP-Link Archer C50 v3 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7612E.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Flash instruction:

The only way to flash LEDE image in ArcherC50v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Henryk Heisig
e39a240ba2 ramips: ArcherC20v4: use common TP-Link dtsi file
and remove common part from dts file.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Henryk Heisig
368a7f4cec ramips: change the TP-Link dtsi filename
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-11 16:04:16 +01:00
Daniel Golle
32f120b783 ramips: various fixes for zbt-we1226
Convert userspace code to use generic device-tree compatible board
detection method.  Users of the existing code will have to use
sysupgrade -F once to switch to the new generic board naming.
Properly setup pinctrl fixing the switch port LEDs.

Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226)
Reported-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-02-06 03:00:33 +01:00
Jackson Ming Hu
21d3643828 ramips: add support for Widora Neo 32MB flash revision
Widora has updated their Widora Neo board recently.

The new model uses 32MB WSON-8 factor SPI flash
instead of the original 16MB SOP-8 factor SPI flash.

All the other hardware components are the same as
the first revision.

Detailed hardware specs listed below:

CPU: MTK MT7688AN
RAM: 128MB DDR2
ROM: 32MB WSON-8 factor SPI Flash (Winbond)
WiFi: Built-in 802.11n 150Mbps?
Ethernet: 10/100Mbps x1
Audio codec: WM8960
Other IO: USB OTG;
	  USB Power+Serial (CP2104);
	  3x LEDs (Power, LAN, WiFi);
	  2x Keys (WPS, CPU Reset)
	  1x Audio In/Out
	  1x IPEX antenna port
	  1x Micro SD slot

Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-23 23:31:09 +01:00
Mathias Kresin
a411881a40 ramips: add flash size postfix to Widora neo
Rename the Widora neo by adding a flash size prefix. Move the common parts
into a dtsi to be prepare everything for upcomming support of the 32MB
version.

Migrate the Widora neo to the generic board detection as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-23 23:31:09 +01:00
Rosen Penev
c25d9cbde8 ramips: Fix GB-PC1 cpuclock again
The intended frequency is 900 MHz, not 90.

Fixes: 7059ab48a6 ("ramips: fix cpuclock for the GB-PC1")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-01-24 07:33:42 +01:00
Daniel Golle
9c4fe103cb ramips: add support for ZBT-WE1226
MT7628NN (580MHz), 8MB SPI NOR, 64MB DDR2 RAM

Everything except for the switch LEDs works great.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-01-23 02:56:57 +01:00
Serg Studzinskii
eb58b14d27 ramips: tl-wr840n-v5: increase firmware partition for 4Mmtk layot
According to console log during TP-Link TL-WR840N v5 OEM firmware update
procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store
router's configuration settings, is erased and recreated again during every
OEM firmware update procedure, thus does not contain any valuable factory data.
So it is conviniant to use this extra 64kB erase block for jffs overlay due
limited flash size on this device like it used on TP-Link's ar71xx boards.

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
2018-01-18 08:04:18 +01:00
Maxim Anisimov
5bdd238b63 ramips: add support for TP-Link Archer C20 v4
TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
  work.

Flash instruction:

The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-01-15 21:45:43 +01:00
Maxim Anisimov
ff1e895530 ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1
This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1"
because of TPLINK released new TP-Link Archer C20 v4. Additionally
migration to the generic board detection has been made.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-01-15 21:45:43 +01:00
Piotr Dymacz
5352669c2c ramips: add support for ALFA Network AC1200RM
ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.

Specification:

- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers

Flash instruction (do it under U-Boot, using UART and TFTP server):

Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Rosen Penev
7059ab48a6 ramips: fix cpuclock for the GB-PC1
The GnuBee PC1 stock bootloader runs at 900Mhz. This fixes bad clock drift when running the platform.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-01-12 08:02:51 +01:00
Mathias Kresin
6912e55e71 ramips: add missing soc compatibles to dts
Add SoC compatibles where missing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-09 22:05:46 +01:00
Mathias Kresin
4dd51788dd ramips: fix Omega2 compatible string
Change the compatibel from Omega to Omega2 and add the compatible string
where missing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-29 22:32:34 +01:00
Mathias Kresin
c7776d4c55 ramips: fix Linkit smart 7688 support
Use a more appropriate compatible string. Fix the wireless led GPIO and
add the default wireless trigger. Use the wireless LED for boot state
indication as well.

Remove the GPIO pinmux for pins not exposed on the board.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-23 15:35:52 +01:00
Henryk Heisig
39e9bfb181 ramips: add support for TP-Link TL-MR3420 v5
TP-Link TL-MR3420 v5 are simple N300 router with
5-port FE switch and non-detachable antennas.
Its very similar to TP-Link TL-WR841N V13.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 8x LED, 2x button, power input switch

Flash instruction:

The only way to flash LEDE image in mr3420v5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-12-23 15:35:52 +01:00
Mathias Kresin
198da20401 ramips: fix devicetree compat strings
"PandoraBox" is not the name of the manufacturer, it's a firmware made by
the manufacturer actually. Their official English name is "D-Team".

PBR-M1 is the only one they use "PandoraBox" as a brand name. Their other
products are using "Newifi" as their trademark (including Y1 and Y1S which
used to be OEM products for Lenovo).

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-21 01:05:16 +01:00
Jackson Ming Hu
c0e131b436 ramips: add support for newifi d2
Previously Newifi D2 could only use PandoraBox M1's firmware.
It works fine, but LED GPIO is different.
As a result, a separated DTS file for this device should be implemented.

Hardware spec:

* CPU: MTK MT7621A
* RAM: 512MB
* ROM: 32MB SPI Flash
* WiFi: MTK MT7603+MT7612
* Button: 2 buttons (reset, wps)
* LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) &
       2 dual-color LEDs (Power, Internet)
* Ethernet: 5 ports, 4 LAN + 1 WAN

Installation method:

Same as Newifi D1, users may need to request unlock code from the device
manufacturer. Otherwise, a SPI flash programmer may be necessary to get
the firmware flashed. After the device is unlocked, press and hold reset
button before power cable plugs in. Then go to http://192.168.1.1 to
upload and flash the firmware package.

Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
2017-12-21 01:05:16 +01:00
Andrew Crawley
fe6f298b07 ramips: add support for Vonets VAR11N-300
The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet
cable, one extra Ethernet port, and an internal antenna, based on the
MediaTek MT7620n chipset.

Specs:
- MT7620n WiSoC @ 600MHz
- 32 MB SDRAM
- 4 MB SPI flash
- 2T2R 2.4GHz WiFi-N
- 1 attached 10/100 Ethernet cable (LAN)
- 1 10/100 Ethernet port (WAN)
- 1 attached USB / barrel 5vdc power cable
- 5 LEDs (see notes below)
- 1 reset button
- 1 UART (3 pads on board)

Installation:

The stock firmware does not support uploading new firmware directly,
only checking the manufacturer's site for updates.  This process may be
possible to spoof, but the update check uses some kind of homebrew
encryption that I didn't investigate.  Instead, you can install via a
backdoor:

1. Set up a TFTP server to serve the firmware binary
(lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin)
2. Factory reset the device by holding the reset button for a few
seconds.
3. Open the web interface (default IP: 192.168.253.254)
4. Log in with the "super admin" credentials: username `vonets`,
password `vonets26642519`.
5. On the "Operative Status" page, click the text "System Uptime", then
quickly click the uptime value.
6. If successful, an alert dialog will appear reading "Ated start", and
the device will now accept telnet connections.  If the alert does not
appear, repeat step 5 until it works (the timing is a bit tricky).
7. Telnet to the device using credentials "admin / admin"
8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin
-r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g
<tftp-server-ip>`
9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4`
10. Reboot

Tested:
- LAN / WAN ethernet
- WiFi
- LAN / WAN / status LED GPIOs (see notes below)
- Reset button
- Sysupgrade

Notes:

LEDs:

The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue
LED for WiFi, and a pair of "status" LEDs connected to the same GPIO
(the blue LED lights when the GPIO is low, and the green when it's
high).  I was unable to determine how to operate the WiFi LED, as it
does not appear to be controlled by a GPIO directly.

Recovery:

The default U-boot installation will only boot from flash due to a
missing environment block.  I generated a valid 4KB env block using
U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an
external programmer.  After this, it was possible to enter the U-boot
commandline interface and download a new image via TFTP (`tftpboot
81b00000 <image-filename>`), but while I could boot this image
sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted
the flash chip.  The sysupgrade file can be written to flash at 0x50000
using an external programmer.

Signed-off-by: Andrew Crawley <acrawley@gmail.com>
2017-12-21 01:05:16 +01:00
Mathias Kresin
95fe3c51e5 ramips: fix polarity in gpio-export node
If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to
enable something, the pin is ACTIVE_HIGH. The same applies to
GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-18 09:32:27 +01:00
Zoltan HERPAI
58e0673900 ramips: add support for Asus RT-N11P / RT-N12+ / RT-N12E b1
This is a variant of the MT7620N-based Asus routers.

Specifications:

- MT7620N (580 MHz)
- 32 MB RAM
- 8 MB Flash
- 5x 10/100Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas
- UART (J2) header on PCB (115200 8n1)

Flash instructions:

1. Configure PC with static IP 192.168.1.75/24
2. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds. All 4 LEDs will
   start to blink, which is when the router will accept firmware files via TFTP.
   No known limitations on firmware filenames, just send it with a TFTP client
   to 192.168.1.1.
3. Router will download file from server, write it to flash and reboot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2017-12-06 17:51:31 +01:00
INAGAKI Hiroshi
18cc8d520c ramips: add missing reset button for Nexx WT1520
This commit adds missing the GPIO key used as reset button.
Nexx WT1520 has a GPIO key for factory reset, but it's not defined in
WT1520.dtsi and cannot use it.

Drop the UART (full) from the device tree source file, it was never
used for this board. Adjust the kernel bootargs accordingly.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note about dropped UART (full) to the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-28 20:59:02 +01:00
Mathias Kresin
aa82141d9b ramips: use pinmux nodes from dtsi
Use the pinmux nodes from the included dtsi file instead of adding
duplicate nodes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-22 08:21:53 +01:00
Mathias Kresin
b69ceb0c3d ramips: add missing pinmuxes to SoC dtsi
Add pinmuxes defined by some board which are including the dtsi files
to the dtsi files itself. Allows to reduce duplication.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-22 08:21:52 +01:00
Mathias Kresin
e142173e8d ramips: backport MT7628 pinmux fixes
According to the datasheet the REFCLK pin is shared with GPIO#37 and
the PERST pin is shared with GPIO#36.

While at it fix a typo inside the pinmux setup code. The function is called
refclk and not reclk.

Update device tree source files accordingly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-22 08:21:52 +01:00
Mathias Kresin
a783185e28 ramips: fix DCH-M225 support
Setting the pins of the UARTF group to GPIO+I2S at the time the I2C
driver loads is to late for the wps GPIO button.

The gpio-keys driver fails to load since the pin used by the wps button
is not yet set to GPIO. The wps button with the rfkill keycode is
essential for this wireless only board.

Add the missing sound and I2C kernel modules corresponding to the
device nodes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-22 08:21:52 +01:00
Felix Fietkau
9996480b0e ramips: add support for ZBT WE3526
This is a variant of the ZBT WG3526 with a few minor modifications.
The wifi chips are swapped, and there is no GPIO controllable status
LED. There is also no SATA port.

Specifications:

- MT7621AT (880 MHz)
- 512 MB RAM
- 16 MB Flash (SPI NOR)
- 5x 1Gbps Ethernet (built-in switch)
- MT7612E 802.11ac 5 GHz WLAN
- MT7603E 802.11n 2.4 GHz WLAN

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-16 12:52:55 +01:00
Piotr Dymacz
fa36bea470 ramips: add support for UniElec U7628-01
UniElec U7628-01 is a router platform board based on MediaTek MT7628AN.
The device has the following specifications:

- MT7628AN (580MHz)
- 64/128/256 MB of RAM (DDR2)
- 8/16 MB of flash (SPI NOR)
- 5x 10/100 Mbps Ethernet (MT7628 built-in switch)
- 1x 2T2R 2.4 GHz Wi-Fi (MT7628)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 2.0 port
- 7x single-color LEDs (GPIO-controlled)
- 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe)
- 1x reset button
- 1x UART header (4-pins)
- 1x SDXC/GPIO header (10-pins, connected with microSD slot)
- 1x DC jack for main power (12 V)

The following has been tested and is working:

- Ethernet switch
- miniPCIe slot (tested with modem and Wi-Fi card)
- miniSIM slot
- sysupgrade
- reset button
- USB 2.0 port*

Due to a missing driver (MMC over GPIO) this is not supported:

- microSD card reader

* Warning:
USB buses in miniPCIe and regular A-type socket are connected together,
without any proper analog switch or USB HUB.

Installation:

This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.

Use the following command to perform the sysupgrade (for the 128MB
RAM/16MB flash version):

sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin

Recovery:

This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.

SDXC/GPIO header (J3):

 1. SDXC_D3  / I2C_SCLK
 2. SDXC_D2  / I2C_SD
 3. SDXC_D1  / I2S_DI
 4. SDXC_D0  / I2S_WS
 5. SDXC_CMD / I2S_CLK
 6. SDXC_CLK / GPIO0
 7. SDXC_CD  / UART_RXD1
 8. UART_TXD1
 9. 3V3
10. GND

Other notes:

1. The board is available with different amounts of RAM and flash. We
have only added support for the 128/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
46ab81e405 ramips: add support for UniElec U7621-06
UniElec U7621-06 is a router platform board based on MediaTek MT7621AT.
The device has the following specifications:

- MT7621AT (880 MHz)
- 256/512 MB of RAM (DDR3)
- 8/16/32/64 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x ASMedia ASM1061 (for mSATA and SATA)
- 2x miniPCIe slots (PCIe bus only)
- 1x mSATA slot (with USB 2.0 bus for modem)
- 1x SATA
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 3.0
- 12x LEDs (3 GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x FPC connector for LEDs (20-pin, 0.5 mm pitch)
- 1x DC jack for main power (12 V)

The following has been tested and is working:

- Ethernet switch
- miniPCIe slots (tested with Wi-Fi cards)
- mSATA slot (tested with modem and mSATA drive)
- miniSIM slot
- sysupgrade
- reset button
- microSD slot

Installation:

This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.

Use the following command to perform the sysupgrade (for the 256MB
RAM/16MB flash version):

sysupgrade -n -F lede-ramips-mt7621-u7621-06-256M-16M-squashfs-sysupgrade.bin

Recovery:

This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.

LEDs list (top row, left to right):

- LED_WWAN# (connected with pin 42 in LTE/mSATA slot)
- Power (connected directly to 3V3)
- CTS2_N (GPIO10, configured as "status" LED)
- TXD2 (GPIO11, configured as "led4", without default trigger)
- RXD2 (GPIO12, configured as "led5", without default trigger)
- LED_WLAN# (connected with pin 44 in wifi0 slot)

LEDs list (bottom row, left to right):

- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- LED_WLAN# (connected with pin 44 in wifi1 slot)

Other notes:

1. The board is available with different amounts of RAM and flash. We
have only added support for the 256/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.

2. The manufacturer offers five different wireless cards with MediaTek
chipsets, based on MT76x2, MT7603 and MT7615. Images of the board all
show that the miniPCIe slots are dedicated to specific Wi-Fi cards.
However, the slots are generic.

3. All boards we got access to had the same EEPROM content. The default
firmware reads the Ethernet MAC from offset 0xe000 in factory partition.
This offset only contains 0xffs, so a random MAC will be generated on
every boot of the router. There is a valid MAC stored at offset 0xe006
and this MAC is shown as the WAN MAC in the bootloader. However, it is
the same on all boards we have checked. Based on information provided
by the vendor, all boards sold in small quantities are considered more
as samples for development purposes.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-14 22:36:46 +01:00
Robert Marko
d0ef27594a ramips: add support for TP-Link TL-WR840N v5
TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and
non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 1x LED (GPIO-controlled), 1x button

* LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
  Orange LED is registered so you can later use it for your own purposes.

  Flash instruction:

  Unlike TL-WR840N v4 flashing through WEB UI works in v5.
  1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image.
  2. Go to 192.168.0.1
  3. Flash the sysupgrade image through Firmware upgrade section of WEB UI.
  4. Wait until green LED stops flashing and use the router.

Notes:
TFTP recovery is broken since TP-Link reused bootloader code for v4 and
that does not take into account only 4 MB of flash and bricks the device.
So do not use TFTP Recovery or you will have to rewrite SPI flash.
They fixed it in later GPL code,but it is unknown which version of
bootloader you have.

After manually compiling and flashing bootloader from GPL sources TFTP
recovery works properly.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-08 23:25:05 +01:00
Edmunt Pienkowsky
9786b53efb ramips: fix Youku-YK1 support
Remove the ephy-pins from the ethernet device tree node. The ephy-pins
are useed to controll the ePHY LEDs and this board doesn't have these.
Instead one of the ePHY pins is used in GPIO mode to control the WAN
LED.

Use the switch LED trigger to control the WAN LED. Move the power LED
handling to diag.sh to show the boot status via this LED.

Add the missing kernel packages for USB and microSD card reader to the
default package selection.

Fix the maximum image size value. The board has a 32MByte flash chip.

Fixes: FS#1055

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
[make the commit message more verbose, remove GPIO pinmux for pins not
used as GPIOs]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-27 11:19:38 +02:00
Kevin Darbyshire-Bryant
bca01fddb3 ramips: remove erroneous "wdt rst" DTS entries
Remove reference to pinmux group "wdt rst" on EW1200, ZBT-WG2626 and
ZBT-WG3526 devices. "wdt rst" is a pinmux function and not a pinmux
group.

Fixes the following error message during boot:

  rt2880-pinmux pinctrl: invalid group "wdt rst" for function "gpio"

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2017-10-25 18:48:51 +02:00
Mathias Kresin
dcf62cb24e ramips: don't enable usb for the WT3020-4M
That device does not have a USB port. It as the same board as the
WT3020-8M, but without soldered USB port port. Also the case lacks the
opening for the port.

Reported-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-25 08:45:05 +02:00
Daniel Kucera
6f008af3f0 ramips: add support for Kimax U25AWF-H1
Kimax U-25AWF-H1 is is a 2,5" HDD Enclosure with Wi-Fi/Eth conection
and battery, based on MediaTek MT7620A.

Patch rewritten from: https://forum.openwrt.org/viewtopic.php?pid=305643

Specification:

- MT7620A CPU
- 64 MB of RAM
- 16 MB of FLASH
- 802.11bgn WiFi
- 1x 10/100 Mbps Ethernet
- USB 2.0 Host
- UART for serial console

Flash instruction:
1. Download lede-ramips-mt7620-u25awf-h1-squashfs-sysupgrade.bin
2. Open webinterface a upgrade
3. After boot connect via ethernet to ip 192.168.1.1

Signed-off-by: Daniel Kucera <daniel.kucera@gmail.com>
[fix reset button gpio, don't add a lan/wan vlan config for single
port board, add -H1 suffix do make sure that this revision of the
board is supported/tested]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-14 10:48:29 +02:00
Sergey Ryazanov
c9f66b1eb9 ramips: keep Archer C20 Power LED On during boot
Keep Archer C20 Power LED in the same state as it was configured by
bootloader (keep it hightlighed) to avoid unexpectable LED turning off
during kernel boot.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-10-04 20:08:15 +02:00
Kevin Darbyshire-Bryant
f2107fc328 ramips: improve Xiaomi Mi Router 3G support
This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d

Improvements:

- Remove software watchdog as hardware watchdog now working as per
  commit 3fbf3ab44f for all mt7621
  devices.

- Reset button polarity corrected - length of press determines reboot
  (short press) vs. reset to defaults (long press) behaviour.

- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
  link and blink on activity.  Green LEDs driven directly by switch
  indicating any link speed and tx activity.

- USB port power on/off GPIO exposed as 'usbpower'

- Add access to uboot environment settings for checking/setting uboot
  boot order preference from user space.

Changes:

- Front LED indicator is physically made of independent Yellow/Amber,
  Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
  indicator, hence the colour behaviour is similar to an RGB LED. RGB
  LEDs are not supported at this time because they produce colour results
  that do not then match colour labels, e.g. enabling 'mir3g:red' and
  'mir3g:blue' would result in a purple indicator and we have no such
  label for purple.
  The yellow, red & blue LEDs have been split out as individual yellow,
  red & blue status LEDs, with yellow being the default status LED as
  before and with red's WAN and blue's USB default associations removed.

- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
  layout. eth0.1 is LAN, eth0.2 is WAN

- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
  leakage between kernel switch init and uci swconfig

uboot behaviour & system 'recovery'

uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed

last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2.  last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok.  If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.

NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.

Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.

Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.

Installation - from stock.

Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
  lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
  from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
  wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot

Recovery - to stock.

Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)

Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'

All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot

The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted.  Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2017-09-28 09:20:36 +02:00
Zoltan Gyarmati
6a5b62f503 ramips: RT5350F-OLINUXINO: enable ttyS1
The RT5350F's second UART pins are available on the base module and on
the EVB as well, so enable it in the device tree.
 In order to keep the origian serial port numbering (ttyS0 is the serial
console), aliases added for the UART devices.

Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
2017-09-28 09:20:36 +02:00
Zoltan Gyarmati
9d8d3d4501 ramips: RT5350F-OLINUXINO: enable i2c
The RT5350F i2c pins is available on the base module and on
the EVB as well, so enable it in the dts.

Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
2017-09-28 09:20:36 +02:00
Zoltan Gyarmati
c1d19b107b ramips: RT5350F-OLINUXINO: invert WiFi LED polarity
The polarity of WLAN_ACT LED on the base module needs to inverted
in order to be 'on' when the WiFi interface is active

Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
2017-09-28 09:20:36 +02:00
Zoltan Gyarmati
862b820f15 ramips: introduce RT5350F-OLINUXINO.dtsi
The RT5350F-OLINUXINO(-EVB).dts files' content are nearly the same, so to avoid
code duplication this patch creates RT5350F-OLINUXINO.dtsi file which
covers the base board's features. The corresponding RT5350F-OLINUXINO.dts
just includes the new .dtsi and the RT5350F-OLINUXINO-EVB.dts adds the EVB
specific GPIO config.

Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
2017-09-28 09:20:36 +02:00
Kevin Darbyshire-Bryant
3fbf3ab44f ramips: fix missing mediatek wdt
mediatek MT7621 soc watchdog DTS id was renamed from "mtk,mt7621-wdt" to
"mediatek,mt7621-wdt" when driver upstreamed to kernel 4.5

Update mt7621.dtsi & mt7628an.dtsi definitions to match upstreamed
kernel.

Restores hardward watchdog functionality on mt7621 devices under linux
4.9

Tested on: MIR3G

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2017-09-22 10:28:59 +02:00
Jiawei Wang
9c500db896 ramips: fix used MAC addresses for Phicomm K2P
The factory partition of the Phicomm K2P contains two MAC addresses.
The lower MAC address is at offset 0xe006 and the higher one is at
offset 0xe000.

Use the lower MAC address as base mac-address which the switch driver
increments by one for the second (wan) vlan.

The MAC addresses are still inverted in contrast to the stock firmware
where the lower MAC address is used for wan. But at least the use of a
MAC address not intended/reserved for this particular board is fixed.

Signed-off-by: Jiawei Wang <me@jwang.link>
2017-09-15 07:14:29 +02:00
Kristian Evensen
133815ad8f ramips: fix D240 mini-PCIe power control GPIOs
In commit b11c51916c ("ramips: Improve Sanlinking D240 config") I made
a mistake with regards GPIO numbering. And in addition to specifying the
wrong GPIO for controling the power of one of the mini-PCIe, I recently
discovered that the power of both slots can be controlled.

This patch specifies the correct GPIO for the left-most mini-PCIe slot
of the D240 (labeled power_mpcie2 since the slot is attached to SIM2),
and adds a GPIO that can be used to control the power of the other
mini-PCIe slot (labeled power_mpcie1).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[do not use the gpio active macros for the gpio-export value]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-09-13 08:07:54 +02:00
Maxim Anisimov
161a3be5ad ramips: add support for TP-Link Archer C20 v1
TP-Link Archer C20 v1 is a router with 5-port FE switch and
non-detachable antennas. It's very similiar to TP-Link Archer C50.
Also it's based on MediaTek MT7620A+MT7610EN.

Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 8x LED (GPIO-controlled*), 2x button, power input switch
- 1 x USB 2.0 port

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the blue part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
  work.

Factory image notes:

These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device.

We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash. So, to flash this device we must
to prepare image using original firmware from tp-link site with uboot.

Flash instruction:

Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot.
There are two ways to flash the device to LEDE:

1) Using tftp mode with UART connection and original LEDE image

 - Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp
   server directory
 - Configure PC with static IP 192.168.0.66/24 and tftp server.
 - Connect PC with one of LAN ports, power up the router and press
   key "4" to access U-Boot CLI.
 - Use the following commands to update the device to LEDE:

    setenv serverip 192.168.0.66
    tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin
    erase tplink 0x20000 0x7a0000
    cp.b 0x80060000 0x20000 0x7a0000
    reset

 - After that the device will reboot and boot to LEDE

2) Using tftp mode without UART connection but require some
   manipulations with target image

 - Download and unpack TP-Link Archer C20 v1 firmware from original web
   site
 - Split uboot.bin from original firmware by this command (example):

    dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1

 - Create ArcherC20V1_tp_recovery.bin using this command:

    cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin

 - Place ArcherC20V1_tp_recovery.bin in tftp server directory.
 - Configure PC with static IP 192.168.0.66/24 and tftp server.
 - Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
 - Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2017-09-13 08:07:54 +02:00
Kristian Evensen
79440ea756 ramips: Add support for ZBT WE1026-5G
The ZBT WE1026-5G
(http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up
to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the
ZBT WE826 image could be used. However, as the name implies, the -5G
comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz
radio, the addition of 5GHz means that a separate image is needed for
the WE1026-5G. I suspect that this image will also work on the previous
WE1026, but I don't have a device to test with.

The WE1026-5G has following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x 5GHz wifi (MT7612)
* 1x button.
* 3x controllable LEDs.

Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).

Not working:
* The 5GHz WIFI LED is completely dead. I suspect the issue is the same
as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is
controlled by the driver, and mt76 (currently) does not support this.

Not tested:
* SD card reader.

Notes:
* The modem (labeled 3G/4G) and power LEDs are controlled by the
hardware.
* There is a 32MB version of this device available, but I do not have
access to it. I have therefor only added support for the 16MB version,
but added all the required infrastructure to make adding support for the
32MB version easy.

Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.

Recovery:
If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the
reset button pressed for ~5sec when booting to start the web server. Set the
address of the network interface on your machine to 192.168.1.2/24, and
point your browser to 192.168.1.1 to access the recovery UI. From the
recovery UI you can upload a firmware image.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-09-11 17:17:05 +02:00
Kristian Evensen
80829022b0 ramips: add support for the HNET C108
The HNET C108
(http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a
mifi based on MT7602A, which has the following specifications:

* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port. Only power is connected, this port is meant for
charging other devices.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
* 6000 mAh battery.
* 5x controllable LEDs.

Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).

Not working (also applies to the factory firmware):
* Wifi LED. It is always switched on, there is no relation to the
up/down state or activity of the wireless interface.

Not tested:
* SD card reader.

Notes:
* The C108 has no dedicated status LED. I therefore set the LAN LED as
status LED.

Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.

Recovery:
If you brick the device, the C108 supports recovery using TFTP. Keep the
reset button pressed for ~5sec when booting to trigger TFTP. Set the
address of the network interface on your machine to 10.10.10.3/24, and
rename your image file to Kernal.bin.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-09-09 09:55:13 +02:00
L. D. Pinney
e9eb6e7bb3 ramips: set ethernet mac address for VoCore2
This patch sets the mac address for the VoCore2 devices.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
2017-08-23 15:09:05 +02:00
Pavel Kubelun
6e283cdc0d ramips: add Xiaomi Mi Router 3G support
This commit adds support for Xiaomi Mi WiFi Router 3G.

Short specification:
 - MT7621AT + MT7603EN + 7612EN
 - 256MB DDR3 RAM
 - 128MB NAND flash
 - 1+2 x 1000M Ethernet
 - 1x USB 3.0 port
 - reset button
 - yellow, blue, red leds

Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: mtd erase kernel0
- run: reboot

Originally stock firmware has following partitions:
 - ...
 - kernel0 (primary kernel image)
 - kernel1 (secondary kernel image, used by u-boot in failsafe routine)
 - rootfs0 (primary rootfs)
 - rootfs1 (secondary rootfs in case primary fails)
 - overlay (used as ubi overlay)

This commit squashes rootfs0, rootfs1 and overlay partitions into 1, so
it can be used by LEDE fully for package installation, resulting in 117,5MiB.

This device lacks hw watchdog, so adding softdog instead (stock does the same).

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-08-23 14:59:12 +02:00
L. D. Pinney
df3295f50e ramips: add support for the VoCore2 Lite
The VoCore2 Lite uses the same PCB as the Vocore2.
This patch moves the common VoCore2 parts into dtsi.

Removed memory node in the device tree source file.
Memory is detected automatically.

http://vocore.io/
http://vonger.net/
http://vonger.cn/

Specifications:
- SoC: MediaTek MT7688AN
- RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H
- Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG
- Wireless: Built into MT7688AN with onboard IPEX connector

Firmware installation:
- VoCore2-Lite ships with firmware forked from OpenWrt.
- Installation from the bootloader is recommended.
- If using luci/sysupgrade use the -n option (do not keep settings)
  original firmware uses a modified proprietary MediaTek wireless driver.
- The wireless is disabled by default in LEDE.
- If reverting to factory firmware using the bootloader is recommended.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Tested by: Noble Pepper <noblepepper@gmail.com>
2017-08-11 18:12:56 +02:00
Mathias Kresin
8c9f847a80 ramips: fix WHR-1166D WAN port
By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.

Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.

Fixes: FS#670

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-11 18:12:56 +02:00
Thibaut VARENE
370aacf532 ramips: ArcherC50v1: fix wlan2g MAC address
By default the wlan eprom contains the generic ralink MAC which is not
the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses
are decremented from the ethernet MAC.

This patch fixes the MAC address for wlan2g in line with OFW.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-08-06 09:22:03 +02:00
Mathias Kresin
313ce3afbb ramips: move common parts into dtsi
Move the common parts of boards with multiple flash size variants into
dtsi files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 19:37:41 +02:00
L. D. Pinney
70b192f573 ramips: update device tree source files
Use the GPIO dt-bindings macros and add compatible strings in the
ramips device tree source files.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 19:37:40 +02:00
Thibaut VARENE
695f5ea85a ramips: Add support for Netgear EX3800
The Netgear EX3800 is essentially an EX3700 with a mains output socket.

Both devices use the exact same firmware image (original firmware is named
EX3700-EX3800-version.chk).

This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and
updating the necessary glue.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-08-03 00:11:25 +02:00
Mathias Kresin
419fa7a15f ramips: cleanup AsiaRF AWM002 eval board support
Cleanup the dtsi files and remove one layer of dtsi. Set the size of
the firmware partition to a value matching the flash size from the
board (variant) name.

Remove the usb led trigger. There is neither a default config for the
usb led trigger nor a LED for usb activity indication.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 00:11:25 +02:00
Mathias Kresin
b82ac84229 ramips: drop AsiaRF AWM003 eval board
Everything is identical to the AWM002 8m eval board. No need to
duplicate it once more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 00:11:25 +02:00
Mathias Kresin
60f6c2b2eb ramips: drop Edimax BR-6425 support
Code to build an image for the Edimax BR-6425 never existed.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 00:07:56 +02:00
Mathias Kresin
1eb1916c5f ramips: add missing partitions
The partitions were lost during migration to device tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 00:07:56 +02:00
Thibaut VARENE
a6f6f8df23 ramips: Archer C50v1: fix power led
01_leds had a workaround for the power led to compensate for the
inverted GPIO state. This patch was missing from my previous commit.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[add the power led default-state which was omitted in the last commit
by me]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-29 12:06:35 +02:00
Thibaut VARENE
0c81bc2969 ramips: Archer C50v1: fix LEDs active levels
All LEDs GPIOs are active low on this device.

WAN and POWER states were inverted. Add default state for power.

Tested on Archer C50v1.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-07-29 09:24:32 +02:00
L. D. Pinney
45dbd65850 ramips: mt7621: add compatible strings
Add compatible strings to all mt7621 based device tree source files to
fix formal issues.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
2017-07-29 09:24:32 +02:00
Oliver Fleischmann
a92c64e8ae ramips: add support for Loewe WMDR-143N
The WMDR-143N is a small module originally used as a Wifi client
in some Loewe smart TV sets. It is sold cheaply at german surplus
shops. The module contains a RT3662 SOC.

Specifications:

- 500 MHz CPU Clock
- 1x 10/100Mbps Ethernet (pin header)
- 32 MB of RAM
- 8 MB of FLASH
- 2T3R 2.4/5 GHz (SOC internal)
- 3 Antennas on PCB
- UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX
  and RX are 3,3V only! The square hole is pin 1
- Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND)
  The square hole is pin 1

The original firmware has two identical kernel/rootfs images and
two "Factory" calibration data blocks in flash. The LEDE image
leaves only the first "Factory" block in place and uses both
"Kernel" blocks and the redundant "Factory" block together to gain
enough space for the jffs2 partition.

Flash instructions:

You need UART and Ethernet connections to flash the board. Use
the LEDE "sysupgrade.bin" image with tftp.

Apply power to the board and in the first 5 seconds, hit 2 to
select TFTP upload. The bootloader asks for board- and server IP
addresses and filename.

Alternate method: With the vendor firmware running, assign an IP
address to the ethernet port, tftp the firmware image to
/tmp and write to mtd4 ("KernelA").

Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de>
[remove pinctrl node from dts, no pin is used as GPIO]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-27 09:13:27 +02:00
John Crispin
6acb53c526 ralink: fix rcu_sched stalls on mt7621
there were 2 bugs
*) core1 came up with a bad bogo mips, looks like the clock needed time to stabilize
*) HPT frequency was not set making r4k timers not come up properly

Signed-off-by: John Crispin <john@phrozen.org>
2017-07-26 09:14:20 +02:00
L. D. Pinney
77645ffcd9 ramips: add support for the GnuBee Personal Cloud One
The GnuBee Personal Cloud One crowdfunded on https://www.crowdsupply.com
    It is a low-cost, low-power, network-attached storage device.

    Specifications:

    - SoC: MediaTek MT7621AT
    - RAM: DDR3 512 MB
    - Flash: 32 MB
    - Six SATA ports for 2.5" Drives
    - One micro SDcard
    - One USB 3.0
    - Two USB 2.0
    - Gigabit Ethernet: 1 x WAN and 1 x LAN
    - UART 3.5mm Audio Jack or 3 pin header - 57600 8N1
    - Four GPIOs available on a pin header

    Flash instructions:

    The GnuBee Personal Cloud One ships with libreCMC installed.
    libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt.
    As such one can upgrade using the webinterface or sysupgrade.

    Das U-Boot has multiple options for recovery or updates including :

    - USB
    - http
    - tftp

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use switchdev led trigger, all interfaces are in vlan1; rename leds
according to board.d setting; remove ge2 group from the pinmux, this
group doesn't exist in the driver]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-25 21:02:53 +02:00
Giuseppe Lippolis
786f7426c2 ramips: fix wps button gpio for DWR-512
The WPS button is at GPIO#7.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-07-25 21:02:53 +02:00
Paul Wassi
c51c976db8 ramips: DTS: VoCore2 improvements/fixes
The VoCore2 features 128MB of RAM, therefore set
memory in DTS to 128*1024*1024 = 0x8000000
The board's LED is connected to GND, set it to
ACTIVE_HIGH here.
Make serial console working again on kernel 4.9 by
change of pinmux configuration.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-07-25 21:02:53 +02:00
Alex Maclean
f683385e73 ramips: add support for TP-Link RE350
The TP-Link RE350 is a wall-wart AC1200 range extender/access point with
a single gigabit ethernet port and two non-detachable antennas, based on
the MT7621A SoC with MT7603E and MT7612E radios.

Firmware wise it is very similar to the QCA based RE450.

SoC: MediaTek MT7621A (880MHz)
Flash: 8MiB (Winbond W25Q64)
RAM:   64MiB (DDR2)
Ethernet: 1x 1Gbit
Wireless: 2T2R 2.4Ghz (MT7603E) and 5GHz (MT7612E)
LEDs: Power, 2.4G, 5G (blue), WPS (red and blue), ethernet link/act
(green)
Buttons: On/off, LED, reset, WPS

Serial header at J1, 57600 8n1:
Pin 1 TX
Pin 2 RX
Pin 3 GND
Pin 4 3.3V

Factory image can be uploaded directly through the stock UI.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2017-07-25 21:02:53 +02:00
Chuanhong Guo
a4c84b2d73 ramips: add support for Phicomm K2P
It uses one MT7615D radio chip with DBDC mode enabled. This mode allows
this single chip act as an 2x2 11n radio and an 2x2 11ac radio at the
same time. However mt76 doesn't  support it currently so there is no
wireless available.

Specification:
- SoC: MediaTek MT7621AT
- Flash: 16 MB
- RAM: 128 MB
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Wireless radio: MT7615D on PCIE0
- UART: 1 x UART on PCB - 57600 8N1

Issue:
- Wireless radio doesn't work due to the lack of driver.

Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2,then follow the instruction to
   set device and tftp server IP address and input the firmware
   file name.U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2017-07-20 19:10:29 +02:00
John Marrett
4531bc4267 ramips: fix GL-inet GL-MT300N-V2 WAN/LAN MAC address
Correct MAC address lookup to appropriate offset based on vendor
source.

Override the WAN MAC to use the same address as LAN. The switch driver
increments the base MAC address for the WAN vlan but the stock firmware
uses the same MAC address for all interfaces.

Based on vendor source commit
https://github.com/domino-team/lede-1701/commit/efb0518

Signed-off-by: John Marrett <johnf@zioncluster.ca>
2017-07-15 07:02:59 +02:00
Piotr Dymacz
24043a0d2e ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.

The difference between these two models is in number of available
LEDs, buttons and power input switch.

This work is partially based on GitHub PR#974.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
  switch

* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Factory image notes:

These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.

We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.

Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.

The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".

Flash instruction:

Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

To access U-Boot CLI, keep pressed "4" key during boot.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Pavlo Samko
82f9486142 ramips: add support for TRENDnet TEW-638APB V2
This patch add support for the TRENDnet TEW-638APB V2.

Specification:
- SoC: Ralink SoC RT3052F
- Flash: 4MB
- RAM: 32MB
- Ethernet: 1x LAN (100 Mbps)
- Wireless: 2.4GHz b/g/n, 2x external antenna
- Buttons: 1x Reset, 1x WPS
- LEDs: Power (green), Ethernet (green), WPS (green and orange),
  Wireless (green)
- UART: 1x UART on PCB (3.3V, GND, RX, TX) - 57600 8N1

Installation

via vendor firmware:
- upload sysupgrade.bin image

via TFTP:
- stop uboot into tftp-load into option "2"
- upload sysupgrade.bin image

Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
2017-06-17 15:38:19 +02:00
小桥
a3332f2aa2 ramips: fix Phicomm K1S(PSG1208) pinmux
Use gpio function for pins with LEDs.

Signed-off-by: 小桥 <29551030@qq.com>
2017-06-12 21:08:54 +02:00
Sven Roederer
9715beb04c ramips: add support for Ubiquiti EdgeRouter X-SFP
This patch adds support for the Ubiquiti EdgeRouter X-SFP and
improves support for the EdgeRouter X (PoE-passthrough).

Specification:
- SoC: MediaTek MT7621AT
- Flash: 256 MiB
- RAM: 265 MiB
- Ethernet: 5 x LAN (1000 Mbps)
- UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
- EdgeRouter X:
  - 1 x PoE-Passtrough (Eth4)
  - powered by Wallwart or passive PoE
- EdgeRouter X-SFP:
  - 5 x PoE-Out (24V, passive)
  - 1 x SFP (unknown status)
  - powered by Wallwart (24V)

Doesn't work:
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.

Installation

via vendor firmware:
- build an Initrd-image (> 3MiB) and upload the factory-image
- initrd can have luci-mod-failsafe
- flash final firmware via LuCI / sysupgrade on rebooted system

via TFTP:
- stop uboot into tftp-load into option "1"
- upload factory.bin image

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2017-06-07 06:33:33 +02:00
Enrico Mioso
acd8649b18 ramips: let the "reserved" MTD partition be RO for R6220
The "reserved" partition should probably be read-only, just in case. Even
not knowing it's content, other devices have marked it as such, so it
seems a good idea to do so also for this device.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Mathias Kresin <dev@kresin.me>
CC: Hanqing Wong <hquu@outlook.com>
2017-05-31 08:45:02 +02:00
Russell Senior
b76248dd96 ramips: remove fictional LEDs from AsiaRF AWM00x device tree
Neither the AsiaRF AWM002 or AWM003 actually has an LED on the module
board.  The ld1 and ld2 do not represent actual LEDs.  These pins might
connect to LEDS on an eval board or other carrier board, but that is
outside the scope of this device tree file.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2017-05-27 07:01:39 +02:00
Kyson Lok
abbfcc8525 ramips: add support for GL-inet GL-MT300N-V2
This patch adds supports for the GL-inet GL-MT300N-V2.

Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)

Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 08:04:15 +02:00
Ørjan Malde
5f932988c3 ramips: add support for Asus RT-AC51U
Specification:
 - SoC: MediaTek MT7620A (580 MHz)
 - RAM: 64 MiB (Winbond W9751G6JB-25)
 - Flash: 16 MiB (Spansion S25FL128SAIF00)
 - LAN: x4 100M
 - WAN: x1 100M
 - Others: USB 2.0, reset button, wps button and 9 LEDs

Issues:
 - 5 GHz band is not functional (missing driver support)

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75;
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the sysupgrade
   image, and press upload

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin
 tftp> quit

Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
2017-05-10 08:45:12 +02:00
Alexey Belyaev
a7cbf59e0e ramips: add new device ZyXEL Keenetic as kn
This device exactly same as NBG-419N but with USB port and USB Led.

Specification:

- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0

Installation via serial console (57600 8N1) from TFTP server
 - rename the firmware to something shorter, for example
   "sysupgrade.bin" (max. 32 chars)
 - copy firmware TFTP server's directory
 - when you power on device, and see U-Boot log, immediatly push "2"
   once.
 - You will see this message:
     2: System Load Linux Kernel then write to Flash via TFTP.
        Warning!! Erase Linux in Flash then burn new one. Are you sure?
 - Push "y", and enter: device IP, then TFTP server's IP, and then
   image firmware file name.

The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).

Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-10 08:45:12 +02:00
Sven Roederer
4c3953ba29 ramips: use GPIO_ACTIVE macros in UBNT-ERX.dts
- reorder includes
- use GPIO_ACTIVE_LOW macro instead of hardcoded "1"

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2017-05-06 09:49:00 +02:00
Jo-Philipp Wich
a45cde9118 ramips: ZTE-Q7: fix switch driver initialization in DTS (FS#716)
Add the changes suggested by FS#716 to fix the switch driver initialization
on the ZTE Q7.

Also remove the `pinctrl-names` field obsoleted by the changes.

Reported-by: Harry Lau <harrylwc@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-04-27 10:44:28 +02:00
Mathias Kresin
bd2727fb25 ramips: ZBT-WE826: include the correct dtsi
Fix a copy/paste error and include the ZBT-WE826 dtsi instead of the
ZBT-WG3526 one.

Fix the syntax error in the ZBT-WE826 dtsi to prevent an compile error.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-27 09:39:34 +02:00
Mathias Kresin
2ddaf96a77 ramips: add ZBT-WE826 32MB variant
The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the
device tree source file, rename the currently supported 16 MByte
version and add the 32 MByte variant.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
3cfc909c54 ramips: rename Digineo AC1200 Pro to ZBT-WG3526 32MB
The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with
unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and
add the sdhci kernel module to use it for multiple clones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
619d68bfc9 ramips: prepare ZBT-WG3526 for hardware variants
The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the
current supported 16MByte version to indicate which flash size variant
is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Jiawei Wang
ff258effd5 ramips: add support for ZBT-WE1326
Specification:
- SoC: MT7621AT, MT7603EN and MT7612EN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 512 MiB (EM6GE16EWXD-12H)
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Others: USB 2.0, micro SD slot, reset button and 8 x LEDs

Issues:
- Two LEDs for 2.4 GHz and 5 GHz Wi-Fi do not work, can't find GPIOs.
- The pwr LED is not GPIO controllable

How to install:
- The original firmware is OpenWrt, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Signed-off-by: Jiawei Wang <buaawjw@gmail.com>
2017-04-25 19:29:59 +02:00
Alexey Belyaev
187624f759 ramips: fix ZyXEL Keenetic Omni/Omni II GPIOs
Each GPIO bank has only 24 gpios. Use and enable the correct banks for
GPIOs > 24.

Signed-off-by: Alexey Belyaev <spider@spider.vc>
2017-04-25 19:29:59 +02:00
Alexey Belyaev
3549bad814 ramips: fix ZyXEL Keenetic Omni switch config
The wan port is connected to switch port 0. Fix the mediatek,portmap as
well as the default switch config.

Signed-off-by: Alexey Belyaev <spider@spider.vc>
2017-04-25 19:29:59 +02:00
Daniel Golle
c6fe325587 ramips: rename PSG1218 to match label
Fix previous commit to be less ambigous:
PSG1218 rev.A = 5 ports, external PA, heatsinks
PSG1218 rev.B = 4 ports, internal PA, no heatsinks

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 02:55:36 +02:00
Daniel Golle
c5a7dc49d1 ramips: split Phicomm PSG1218 and PSG1218K2C
PSG1218 got only 4 Ethernet ports and WAN on port 3 while
PSG1218K2C got 5 Ethernet ports and WAN on port 4
Switch to use kmod-kt76x2 instead of kmod-mt76 for both devices while
at it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 02:29:21 +02:00
Mathias Kresin
b4be4617b5 ramips: add RP-N53 pcie wireless eeprom
Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata.
Disable the 2.4GHz band as this band has no antennas attached but is
enabled in the eeprom/caldata.

Fixes: FS#691

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
21abb7492c ramips: fix WHR-600D eeprom dt property
Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as
this board have a RT5592 and uses the rt2x00 driver. The mediathek
device tree bindings do not work here.

Fixes: FS#691

Fixes: d8dd207ea6 ("ramips: use the ralink,mtd-eeprom device tree property")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-13 08:18:57 +02:00
Mathias Kresin
c59469b908 ramips: fix Xiaomi MiWiFi Nano firmware partition size
Even the commit message of the patch adding support for the MiWiFi Nano
says that a 16 MB flash chip is used. Extend the firmware partition to
make use of all available flash space.

Fixes: FS#622

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-03-24 08:09:39 +01:00
Vaclav Svoboda
815cc2a69a ramips: add support for Zbtlink ZBT-WE2026
This patch adds support for the Zbtlink ZBT-WE2026.

Specification:
- SoC: MediaTek MT7620N (580MHz)
- RAM: 64 MiB
- Flash: 8 MiB SPI
- LAN: 4x100M
- WAN: 1x100M

Installation through bootloader webserver:
- With the power unplugged press and hold reset button.
- Plug power and hold reset button until LED starts to blink.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
2017-03-17 08:58:50 +01:00
Joseph C. Lehner
de33a4cef0 ramips: add support for Netgear EX3700
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the device's web
interface or via nmrpflash.

Co-authored-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Paul Oranje <por@xs4all.nl>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-03-12 09:28:19 +01:00
Hanqing Wong
38bee61dab ramips: add support for Netgear R6220
This patch adds support for the Netgear R6220, aka Netgear AC1200 and
R6220-100NAS.

Specification:
- SoC: MediaTek MT7621ST (880 MHz)
- Falsh: 128 MiB (Macronix MX30LF1G08AA-TI)
- RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
- Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- Serial baud rate of Bootloader and factory firmware: 57600

Installation through telnet:
- Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port
  on the router.
- Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
  (login if required, default: admin password)
- You will see "Debug Enabled!"
- Telnet 192.168.1.1 and login with "root"
- ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for
  example.
- cd /mnt/shares/myUdisk
- mtd_write write rootfs.bin Rootfs
- mtd_write write kernel.bin Kernel
- reboot

nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.

Signed-off-by: Hanqing Wong <hquu@outlook.com>
2017-03-12 09:28:05 +01:00
Kristian Evensen
b11c51916c ramips: Improve Sanlinking D240 config
* The left most mini-PCIe slot (the one attached to SIM2) can be
power-cycled by setting GPIO 0 to high/low.

* The D240 only needs the MT76x2 module, so update makefile to reflect this.
Note that until the default mt7620 target is updated, then kmod-mt76 (and thus
kmod-mt7603) will be selected by default.

v2->v3:
* Indentation error.

v1->v2:
* Rename gpio and remove redundant comment (thanks Piotr Dymacz)

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-03-11 08:36:52 +01:00
Francois Goudal
9b35815f0f ramips: add support for Afoundry EW-1200
This device features both a 2.4 and 5Ghz radio, and supports
802.11a/b/g/n/ac modes.
It has 5 Gb-Ethernet ports and a USB 3.0 host port.

It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi
chipsets, together with 128MB of RAM and 16 MB of SPI Flash.

The stock firmware is in fact based on some openwrt barrier breaker, with a
mediatek SDK kernel, and an afoundry custom made web interface (not LuCI
based).
Firmware update page on the stock web interface can not accept sysupgrade
images, it bricks the device.
At this point, the only working solution I found was to connect to the
serial console port (available on J4 header) and to use opkg to install
dropbear.
Then scp the sysupgrade file in the device's /tmp and run sysupgrade from
console without preserving configuration files.

Signed-off-by: Francois Goudal <francois@goudal.net>
2017-03-01 22:29:50 +01:00
ZengFei Zhang
edae3479e6 ramips: add support for HiWiFi HC5962
This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com

Short specification:

 - MT7621AT + MT7612EN + 7603EN
 - 256MB DDR3 RAM
 - 128MB NAND flash
 - 1+3 x 1000M Ethernet
 - 1x USB 2.0 port. 1x USB 3.0 port.
 - reset button
 - UART pad on PCB (JP3: TX, RX, GND, 3.3V)

Flash instruction:

1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin
2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/
3, use the following commands:
   $ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware
   $ mtd erase firmware_backup && reboot
After reboot you should be able to login as root via SSH on 192.168.1.1

Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
2017-02-28 23:46:02 +01:00
Wang JiaWei
d48cc5e044 ramips: add support for HiWiFi HC5661A
HC5661A is almost the same as HC5661 but MT7628AN is used instead of MT7620A.

- MT7628AN
- 128 MiB DDR2 RAM (W971GG6KB-25)
- 16 MiB SPI NOR flash (W25Q128)
- SD slot (not work yet)
- 1+4 x 100M Ethernet
- 802.11 b/g/n Wi-Fi
- 3 x LED
- 1 x button
- UART pad on PCB (JP1: TX, RX, GND, 3.3V)

The factory flash layout seems different from HC5661.
"hwf_config" is renamed to "oem" and its size changes to 0x20000.
It is modified accordingly in the dts file.

0x000000000000-0x000000030000 : "u-boot"
0x000000030000-0x000000040000 : "hw_panic"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000160000 : "kernel"
0x000000160000-0x000000fc0000 : "rootfs"
0x000000bb0000-0x000000fc0000 : "rootfs_data"
0x000000fc0000-0x000000fe0000 : "oem"
0x000000fe0000-0x000000ff0000 : "bdinfo"
0x000000ff0000-0x000001000000 : "backup"
0x000000050000-0x000000fc0000 : "firmware"

To install LEDE, enabled the "developer mode",
which will *void your warranty* and open the SSH server at port 1022.

sysupgrade -n -F lede-ramips-mt7628-hc5661a-squashfs-sysupgrade.bin

SD slot:
- Tried to add modules kmod-sdhci kmod-sdhci-mt7620, and corresponding dts block.
- It will block WAN + 3xLAN ports, only one LAN works.
- I'm not sure why, everything else works fine.

Signed-off-by: Wang JiaWei <buaawjw@gmail.com>
2017-02-27 11:39:31 +01:00
Furong Xu
00343e18f2 ramips: fix PWM pin mux conflict in dtsi
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict

[    0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[    0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[    0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0  on device rt2880-pinmux
[    0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back

Keep PWM disabled.

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-16 09:09:09 +01:00
Daniel Golle
d57223259b ramips: replace remaining instances of ralink, port-map
Some boards were apparently forgotten when ralink,portmap was renamed
to mediatek,portmap -- probably because they used the long obsolete
ralink,port-map attribute.
If this commit breaks ethernet wan/lan assignment, this is because
the port-map attribute wasn't actually parsed, you'll have to replace
"wllll" by "llllw" in the dts file belonging to that board (and send
a patch doing that!)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-02-15 09:12:40 +01:00
Giuseppe Lippolis
35c60d18c5 ramips: export slic IRQ line in dwr-512
The DWR-512 embeds the hw slic device si3210. This device have the IRQ line
attached to the gpio1. This patch export the gpio1 with proper name and
parameters to the sysfs.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-15 07:45:54 +01:00
Furong Xu
a9fdb35740 ramips: Clean duplicated status property for Omega2 WMAC in dtsi
At the tail of dtsi, wmac is enabled twice, clean the first one

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-14 12:19:56 +01:00
Giuseppe Lippolis
85766c8d70 ramips: fixed sms led polarity into dwr-512 DT
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-14 12:19:35 +01:00
Kristian Evensen
bb7068f26c ramips: add support for Sanlinking D240
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-02-05 22:23:28 +01:00
Giuseppe Lippolis
f9f636b94e rt5350: added pcm interface in .dtsi
Added the missing audio pcm interface in the .dtsi file for the rt5350
device. The update has been verified from the data get from the datasheet
and is very similar to the mt7620a.dtsi

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-03 05:10:13 +01:00
Mathias Kresin
a0888ecbaf generic: rtl8366rb: fix compatible string
Use a vendor prefix as it has to be for all not core driver. Update the
compatible string in the device tree files accordingly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 00:46:03 +01:00
Mathias Kresin
2c4d81310f ramips: fix Sercomm NA930 compatible string
The Sercomm NA930 is not a mt7620a evaluation board and shouldn't use
the eval board compatible string.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 00:46:03 +01:00
Mathias Kresin
2281f9929b ramips: remove Planex CS-QR10 sound device tree node
The comptible string is neither added by any LEDE patch nor exists in
in the kernel. Drop the sound node which was obviously added
accidentally with 9195d8da ("ramips: DTS rework").

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 00:45:55 +01:00
Mathias Kresin
05b1fcc70b ramips: cleanup SPI flash device tree properties usage
Use only the jedec,spi-nor compatible string. Everything else either
never worked or is only support to keep compatibility.

Remove the linux,modalias property. It is obsolete since kernel 4.4.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-02 22:48:54 +01:00
Felix Fietkau
dabdd123c9 mt76: update to the latest version
Uses upstream code to parse DT supported band/frequency information.
Update existing .dts files to the new format and remove unnecessary
overrides.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-01 17:49:55 +01:00
Felix Fietkau
2340de62a6 ramips: remove DT pcie nodes for GL-MT300A/N
These devices don't have a secondary wifi chip

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-01 17:49:54 +01:00
FUKAUMI Naoki
6b0b526a4f ramips: add support for Buffalo WCR-1166DS
Buffalo WCR-1166DS is a small wireless router with

 - MT7628AN + MT7612E
 - 64MiB DDR2 SDRAM
 - 16MiB SPI flash
 - 2T2R 11ac/a/b/g/n Wi-Fi
 - 2x 10/100M ethernet switch
 - 8x programmable LED
 - 3x button
 - UART pad on PCB (J2: 3.3V, GND, TX, RX)

factory image can be installed via stock web UI.

due to the "dual image" function in the bootloader, the second half of
the SPI flash ("firmware2" partition) cannot be used as a part of the
file system.

Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
2017-01-31 11:10:58 +01:00
Felix Fietkau
bc32f7deb5 ramips: add missing DTS pcie node for WSR-600
Enables PCI bus and support for the MT7603 and RT5592 chips

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-31 10:27:38 +01:00
Tobias Wolf
99eb6f97e5 ramips: enable rlt8366s Green Feature for F5D8235 V1
Enable the green feature for the board by default.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2017-01-27 11:10:10 +01:00
Tobias Wolf
d43046e0f6 ramips: add rlt8366s initvals to the F5D8235 V1 DTS
Before this change only port 4 of F5D8235 V1 worked at 1000Mpbs.

Comparing the current driver with the GPL_BELKIN_F5D8235-4_v1000
v1.01.24 sources showed that additional steps are required to set-up
the rlt8366s switch correctly.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2017-01-27 11:10:10 +01:00
Vitaly Chekryzhev
9a53e1bdf9 ramips: ZyXEL Keenetic Omni/Omni2: export gpio usb power
Export gpio usb to allow power management of USB port.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-26 16:39:08 +01:00
Vitaly Chekryzhev
e8c265b2cc ramips: ZyXEL Keenetic Viva: export gpio usb power
Export gpio usb to allow power management of USB port.

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
2017-01-26 16:39:08 +01:00
Joseph C. Lehner
0cc04d05f6 ramips: fix EX2700 wireless mac
On some EX2700 devices, the MAC address from the eeprom data differs
from the actual MAC address. Fix that, and cleanup the DTS file
while we're at it.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
2017-01-26 13:53:57 +01:00
Thibaut VARENE
7fb11c8ed2 ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-01-18 12:06:16 +01:00
BangLang Huang
2a7f669016 ramips: fix mac address of miwifi-mini
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
2017-01-18 12:05:14 +01:00
Lazar Demin
ab90f15c89 ramips: Added Onion Omega2 and Omega2+
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>
2017-01-15 17:43:14 +01:00
Yo Abe
29097b95ba ramips: fix WLI-TX4-AG300N boot and network
Partition label "linux" prevents the root file system to be mounted at
boot time leading to a kernel panic. After changing it to "firmware",
the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data"
are correctly recognized.

The attached IP175C 10/100 MBit switch cannot connect to a link with
fixed 1000Mbit speed. The correct link speed is 100MBit. The switch
is detected and can be configured via mdio bus and should allow two
separable VLANs to be configured for the 4 available ports.

Signed-off-by: Yo Abe <abe.geel@gmail.com>
[picked from openwrt/PR#330]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-13 08:32:35 +01:00
Andrew Yong
3f31029b19 ramips: add support for VoCore2
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
2017-01-13 08:32:35 +01:00
L. D. Pinney
b28e94d4bf ramips: MiWiFi Nano fixes
Use the the dt-bindings macros and add the reset button.

Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.

Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-01-02 19:16:54 +01:00
Mathias Kresin
0cf581ca3a ramips: use new image build code for more devices
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-12-24 10:03:38 +01:00