Commit graph

48 commits

Author SHA1 Message Date
John Crispin
b7f115f22a ipq806x: drop ipq40xx support
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00
Dongming Han
04d3308b62 ipq806x: add support for GL.iNet GL-B1300
This patch adds support for GL.iNet GL-B1300

Specification:
- SOC:        IPQ4028 / QCA Dakota
- RAM:        256 MiB
- FLASH:      32 MiB
- ETH:        Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB:        1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1:      Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2:      Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT:      one reset and one WPS button
- LEDS:       3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART:       1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1

Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
  192.168.1.2 have that file.
- the wifi led will be flashing when writing image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2018-02-14 09:40:32 +01:00
David Bauer
1113fcdc80 ipq806x: mark AVM FB4040 switchport as untagged
This commit marks the CPUs switchport explicit as untagged.
Otherwise, an eth0.1 interface is created and the devices
LAN-ports are not working.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-02-11 16:02:52 +01:00
Sven Eckelmann
86e18f6706 ipq806x: add support for OpenMesh A42
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
  - 802.3af POE on Ethernet 1
  - 18-24v passive POE (mode B) on Ethernet 2

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 08:00:14 +01:00
Luis Araneda
7293499f71 ipq806x: Sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda
33f09cf151 ipq806x: convert to dt-based board-detection
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree

Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script

Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda
09e13bd341 ipq806x: add a helper variable with the vendor name stripped
This will allow to maintain the current syntax for LEDs config
when switching to a device tree compatible string boardname.

None of the current boards use a comma in the boardname, so they
will be unaffected.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:02 +01:00
Christian Lamparter
da6fdce365 base-files: unify get_dt_led helper function
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.

This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.

Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2017-12-14 09:29:30 +01:00
Roman Yeryomin
156f2df879 ipq806x: ipq4019: add ap-dk01.1-c1 board support
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)

First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize

Further upgrades via sysupgrade.

Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition

Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.

Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.

Changes since v2:
- based on dts(i) rework/cleanup submitted:
  http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2017-10-30 01:24:26 +02:00
Stefan Lippers-Hollmann
189433e543 ipq806x: nbg6817: sync MAC addresses to the upstream values
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.

interface	  new/ OEM MAC	old MAC

wlan-2.4g (phy1): ethaddr	undefined
wlan-5g   (phy0): ethaddr + 1	undefined
lan             : ethaddr + 2	ethaddr
wan             : ethaddr + 3	ethaddr + 1

This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2017-11-03 20:04:51 +01:00
Baptiste Jonglez
5889f92f7d ipq806x: Archer C2600: fix switch ports numbering
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device.  Fix the order so that they match.

Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
2017-08-24 08:39:12 +02:00
Mathias Kresin
f12a32630f treewide: use the generic board_name function
Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Pavel Kubelun
189239ade3 ipq806x: qca99xx: fix wifi calibration
As of now OTP is being correctly parsed and the driver requires to parse pre-caldata to follow corresponding routine.

Rename cal file into pre-calfile so the board initialized correctly with API 2 board data (board-2.bin).

Also remove the now unneeded for qca9984 board.bin symlink to 5GHz calfile.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-06-17 11:51:41 +02:00
Jo-Philipp Wich
3c3f7cfe4d ipq806x: fix EA8500 switch configuration
Do not assign the CPU port twice, this confuses LuCI and possible other
programs relying on topology information in board.json.

Ref: https://github.com/openwrt/luci/issues/1086

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-05-03 14:15:34 +02:00
Christian Lamparter
1cb406d019 ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB Nanya NT5CC128M16IP
FLASH:	32 MiB MXIC MX25L25635FMI
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
	1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:	Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one WLAN and one WPS button
LEDS:	Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1. The SoC's serial port is right
	next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
	header for it. Use a multimeter to figure out the pinout!

This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.

Install Procedure:
 0. It's highly recommended to connect to the serial port.
    The serial settings are listed above.
 1. install a u-boot image for AVM Fritz!Box 4040
    (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
    <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
 2. upload the initramfs.itb image via tftp (u-boot listens to
    192.168.1.1 - use binary transfer mode!)
 3. connect to the FB4040 and use sysupgrade sysupgrade.bin
    to install the image.

Works:
	- Switch and Ethernet (99%)
        - Buttons (WLAN, WPS)
        - FLASH (1 x 32MiB NOR Chip)
        - WLAN2G and WLAN5G
        - CPUFREQ scaling
        - PRNG
        - serial
        - Crypto Accelerator
        - sysupgrade (Read the flash instructions to avoid bricking)
        - full LEDE Install (Read the flash instructions to avoid bricking)
	- LEDs (Power, WAN, Info (red and amber), LAN)
          The LEDs are connected to the QCA8075 LED ports.
	  The AR40xx driver contains a gpio-controller to
	  handle these special "GPIOs".
        - USB Both 3.0 and 2.0 ports
        - many packages from other ARMv7 boards
          (This does include the RaspberryPi Model 2!)
        - ...

Not planned:
	- WAN<->LAN short-cut
	- Qualcomm Secure Execution Environment
        - ...

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Jo-Philipp Wich
ea269c37b8 ar71xx/ipq806x/mediatek/mvebu: fix network defaults
After "73d923e base-files: emit tagged switch configuration by default"
some default network configurations are broken because the lan and wan
ifnames are forcibly set to untagged netdevs.

Adjust the offending set_interfaces_lan_wan() calls to use the proper
tagged device names.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-02-07 09:32:28 +01:00
Hannu Nyman
c980147527 ipq806x: fix wireless macs
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.

Fixes: FS#451

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-02-03 19:31:45 +01:00
Zhang Jingye
71a39b8690 ipq806x: Fix wireless support for Netgear Nighthawk X4S D7800
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.

This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.

Signed-off-by: Zhang Jingye <934526987@qq.com>
2017-01-18 12:05:18 +01:00
Mathias Kresin
3228c2a682 ipq806x: more dts cleanup
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.

Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.

Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.

If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.

Use the usb pinmux settings from the nbg6817 gpl sources.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:33:54 +01:00
Henryk Heisig
e3caadc69d ipq806x: clean up dts files
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).

This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.

Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.

Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.

Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.

Change gpioexport to gpio pinmux.

Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.

Remove pcie pinmux from D7800.

Move pinctrl to correct place in NBG6817 and R7800.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-27 15:24:59 +01:00
Sebastian Quilitz
ae79c41286 ipq806x: add support for TP-Link Archer VR2600v
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.

It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.

To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.

Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
2016-11-24 22:37:40 +01:00
Henryk Heisig
c380772c19 ipq806x: c2600: change wan and lan led trigger to swconfig port
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-21 10:04:55 +01:00
Pavel Kubelun
5aace5a5fb ipq806x: fixes for R7800 and C2600
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
bf7166e545 ipq806x: fix leds, sata port for Netgear R7800 and minor fixes - renamed leds in correct color accordance - blink power led with white during boot and with amber when flashing firmware - fixed usb leds - enabled unused wps and rfkill leds as wlan leds. Now rfkill led is for 2.4GHz and wps - 5GHz WIFI - removed unneeded bootargs - removed unneeded pci pins from R7800 DT (driver already handles it in proper way) and add tx offsetting - nand ecc step size - fixed sata ports
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Cezary Jackiewicz
dafbc94f95 ipq806x: TP-Link Archer C2600: convert old usbdev trigger to new usbport
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-11-03 08:21:32 +01:00
André Valentin
a0ed7af6c6 ipq806x/nbg6817: add support for ZyXEL NBG6817
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:46 +02:00
Henryk Heisig
bcfb535730 ipq806x: C2600: change leds colour name
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Henryk Heisig
4bdf615878 ipq806x: add support for indicating the boot and upgrade state using four leds
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Pavel Kubelun
9677bfbb0f ipq806x: fix wlan mac for Netgear R7800
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-10-06 08:01:33 +02:00
Cezary Jackiewicz
9417293366 ipq806x: Archer C2600: Renaming LED accordance with the standard
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
2016-08-24 00:21:34 +02:00
Alexis Green
c34f953fef ipq806x: Build image for Netgear Nighthawk X4 R7500v2
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-08-22 17:24:48 +02:00
Adrian Panella
184087f4f1 ipq806x: enable ieee80211 phy hotplug and patch macaddress
Calibration data for QCA99x0 in this device has bogus macaddress.
The data cannot be modified directly, as it breaks checksum control.
Instead change the macaddress from phy add hotplug event.

Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-22 19:32:06 +02:00
Pavel Kubelun
823242185b ipq806x: add initial support for Netgear R7800
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-06-22 19:32:06 +02:00
Adrian Panella
3d067c0132 ipq806x: base-files: add support for Linksys EA8500
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-13 22:51:42 +02:00
Signed-off-by: Henryk Heisig
8ee30ade17 ipq806x: add diag.sh script
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-06-05 23:23:57 +02:00
Ash Benz
7d963efc40 ipq806x/base-files: extract ath10k caldata
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
Ash Benz
98b50f0bef ipq806x/base-files: Add Archer C2600 LEDs and board
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
John Crispin
dc92917409 image / basefiles: make console password configurable
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
Signed-off-by: John Crispin <john@phrozen.org>
2016-04-18 21:53:07 +02:00
John Crispin
78a6a9aec3 ipq806x: Add support for Netgear D7800
Signed-off-by: Tathagata Das <tathagata@alumnux.com>

SVN-Revision: 48360
2016-01-19 10:16:36 +00:00
Jo-Philipp Wich
67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
Jo-Philipp Wich
08848936dd all: remove redundant board.d/00_model files
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47753
2015-12-04 11:07:06 +00:00
Jo-Philipp Wich
527ec2af59 all: remove dummy ucidef_set_interface_loopback() from board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47744
2015-12-03 23:13:00 +00:00
Jo-Philipp Wich
80a3e65a9d kirkwood, ipq806x: fix board.d script permissions
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47735
2015-12-03 22:42:13 +00:00
Jo-Philipp Wich
4615944c71 ipq806x: switch from uci-defaults to board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47730
2015-12-03 21:13:12 +00:00
Jonas Gorski
8b4df1efd5 ipq806x: add support for Netgear Nighthawk X4 R7500
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.

Known issues:
 * 5 GHz wifi not working - there is no quantenna driver
 * One of the USB ports is not working

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46796
2015-09-04 14:46:06 +00:00
John Crispin
0ddebefc74 ipq806x: add db149 support to OpenWrt init scripts
DB149 is a IPQ8064 based platform. This patch adds the init scripts to
detect it, configure the network accordingly, and generate a flashable
image for it.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45537
2015-04-21 07:15:47 +00:00
John Crispin
de7100d818 ipq806x: initialize the network on AP148
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 44522
2015-02-24 12:00:04 +00:00
John Crispin
3c1f6e358d ipq806x: Add support for IPQ806x chip family
Patches are generated using the "format-patch" command from the
following location:
*https://www.codeaurora.org/cgit/quic/kernel/galak-msm/log/?h=apq_ipq_base
*rev=0771849495b4128cac2faf7d49c85c729fc48b20
Patches numbered 76/77/102/103 have already been integrated in 3.14.12,
so they're not in this list.

All these patches are either integrated are pending integration into
kernel.org, therefore these patches should go away once the kernel
gets upgraded to 3.16.

Support is currently limited to AP148 board but can be extended to other
platforms in the future.

These changes do not cover ethernet connectivity.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 42334
2014-08-30 09:32:58 +00:00