Commit graph

220 commits

Author SHA1 Message Date
Hauke Mehrtens
5b089e45a6 kernel: update 4.4 kernel to 4.4.42
Refresh patches on all 4.4 supported platforms.
Compile & run tested: lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-01-13 23:05:36 +01:00
Felix Fietkau
c2fc52ae22 kernel: remove DEVMEM/DEVKMEM platform overrides
Those options are handled via top-level menuconfig instead

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-10 13:48:53 +01:00
Pavel Kubelun
6ebb46a40a ipq806x: fix pvs1_bin voltage in ipq8065 DT
Fixing pvs1 bin voltage as found in GPL tarball and Qualcomm SDK.

Also adjusting smb208_s2a/b minimum voltage to reflect lowest value in pvs table.

Current ipq8065 devices in LEDE choose (based on eFuse data) pvs bin n4, that has
correct values in DT, but in future a new device may choose n1 or n6.

Without this change n1 is semi-correct and n6 is not available, because OPP driver
disregards bins with voltage values that regulator cannot supply.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2017-01-10 08:11:14 +01:00
Felix Fietkau
018d80007e kernel: remove ubifs xz decompression support
It has been unused, and less useful than squashfs for cases where flash
space usage matters.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-01-09 14:07:06 +01:00
Adrian Panella
d700c120bf ipq806x: EA8500 fix sysupgrade over stock firmware
When running sysupgrade for the first time over the second partition
(that still had stock firmware) the rootfs wasn't flashed as there
wasn't enough space.
This happend because stock also uses UBI, but the volume name wasn't
recognised and wasn't deleted before flashing.

Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-12-20 09:35:37 +01:00
dissent1
fef6a96d9e ipq806x: add thermal sensor driver
Allows to check cpu temperature.

Huge thanks to @hnyman for valuable assistance!

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-12-01 15:47:43 +01:00
Pavel Kubelun
2b71f958b1 ipq806x: increase coherent dma pool size
Cherry-picked and rebased from
https://source.codeaurora.org/quic/qsdk/system/openwrt/tree/?h=korg/linux-3.4.y/release/arugula_bb_cs

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-12-01 15:47:43 +01:00
Pavel Kubelun
8fca99266e ipq806x: add enable reg and masks for PRNG
Cherry-picked from https://source.codeaurora.org/quic/qsdk/system/openwrt/tree/?h=korg/linux-3.4.y/release/arugula_bb_cs

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-12-01 15:47:43 +01:00
Pavel Kubelun
550f71ec8d ipq806x: refactor rpm clock controller patches
RPM clock controller driver had made its way upstream and previous
approach of directly redoing a driver to support ipq806x is a no go anymore.

Thus reverting mentioned patches to upstream state and renaming
in correct patch numbering accordance.

To make the driver work on ipq806x boards we introduce a custom patch.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-12-01 15:47:43 +01:00
Kevin Darbyshire-Bryant
102cb4742c kernel: bump to 4.4.35
Refresh patches on all 4.4 supported platforms.

077-0005-bgmac-stop-clearing-DMA-receive-control-register-rig.patch
removed as now upstream.

Compile & run tested: ar71xx - Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2016-11-29 21:12:08 +01:00
Mathias Kresin
3228c2a682 ipq806x: more dts cleanup
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.

Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.

Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.

If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.

Use the usb pinmux settings from the nbg6817 gpl sources.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-11-27 15:33:54 +01:00
Henryk Heisig
e3caadc69d ipq806x: clean up dts files
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).

This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.

Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.

Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.

Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.

Change gpioexport to gpio pinmux.

Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.

Remove pcie pinmux from D7800.

Move pinctrl to correct place in NBG6817 and R7800.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-27 15:24:59 +01:00
Sebastian Quilitz
ae79c41286 ipq806x: add support for TP-Link Archer VR2600v
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.

It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.

To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.

Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
2016-11-24 22:37:40 +01:00
Henryk Heisig
c380772c19 ipq806x: c2600: change wan and lan led trigger to swconfig port
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-21 10:04:55 +01:00
Henryk Heisig
8b1731964b ipq806x: enable swconfig LED support
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-21 10:04:55 +01:00
Pavel Kubelun
70434c3f94 ipq806x: switch to upstream usb driver and backport fixes
Also removing fifo-resize property drom DT as it has been removed from the driver.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-21 09:58:42 +01:00
Felix Fietkau
b5ee86c4e5 ipq806x: remove device specific sysupgrade image checks
Replaced by image metadata

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-20 20:08:39 +01:00
Pavel Kubelun
27c355f8a4 ipq806x: fix build errors
Add missing patches that broke LEDE builder while updating WDT driver

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-19 17:57:09 +01:00
Felix Fietkau
9d6d7d9a0e ipq806x: append metadata to images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
Hannu Nyman
8459d85fa3 ipq806x: refresh patches
This patch refreshes the ipq806x kernel patches.

There was a large PR for ipq806x in the queue when the kernel patches
were refreshed for 4.4.32, so currently there is quite much fuzz for
ipq806x.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2016-11-17 14:23:01 +01:00
Pavel Kubelun
5aace5a5fb ipq806x: fixes for R7800 and C2600
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
3ac5eb9141 ipq806x: fix Netgear R7500v2 memory
Netgear R7500v2 has 512MB of RAM with 2MB reserved block in the end of memory region.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
bb8f5162fd ipq806x: fix pci pins
Fix pci pins drive-strength according to oem sources.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
84781cb6dc ipq806x: add vlans during switch init into R7800 DT
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
77b6bfc2f5 ipq806x: add support for RPM message RAM
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
dissent1
07d0c1b947 ipq806x: add support for RPM clock controller
The patch #179 for RPM has initially been made for apq806x board. It has been modified to support ipq806x instead of apq8064.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
506dc815b9 ipq806x: add CPU idle states
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
793d448a51 ipq806x: backport upstream wdt driver
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-16 10:59:30 +01:00
Pavel Kubelun
524d7a7cde ipq806x: fix pcie reset gpios
Fix perst-gpios property in accordance to the driver, so it stops spamming that it can't parse it.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-08 11:17:10 +01:00
Felix Fietkau
3616666126 ipq806x: fix zyxel image build error
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
Felix Fietkau
fcf90318c5 ipq806x: clean up the kernel config and reduce kernel image size by disabling some unnecessary code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
Felix Fietkau
fddd532612 ipq806x: fix a kconfig issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-04 13:06:35 +01:00
Pavel Kubelun
b2135f3ba5 ipq806x: update DT in accordance to new drivers And add some more DT nodes
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
681f28990d ipq806x: switch to generic cpufreq driver cpufreq-dt
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver

Also switching to ondemand frequency scaling as it is fixed now

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
a154a3d8be ipq806x: add opp patches for voltage scaling
Preparing for cpufreq driver switch to generic cpufreq-dt

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
8749fb7894 ipq806x: update clk-qcom patches
Preparing for cpufreq driver switch to generic cpufreq-dt

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Pavel Kubelun
bf7166e545 ipq806x: fix leds, sata port for Netgear R7800 and minor fixes - renamed leds in correct color accordance - blink power led with white during boot and with amber when flashing firmware - fixed usb leds - enabled unused wps and rfkill leds as wlan leds. Now rfkill led is for 2.4GHz and wps - 5GHz WIFI - removed unneeded bootargs - removed unneeded pci pins from R7800 DT (driver already handles it in proper way) and add tx offsetting - nand ecc step size - fixed sata ports
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-11-03 08:28:16 +01:00
Cezary Jackiewicz
dafbc94f95 ipq806x: TP-Link Archer C2600: convert old usbdev trigger to new usbport
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
2016-11-03 08:21:32 +01:00
Pavel Kubelun
8f7e58c0fe ipq806x: add reserved memory node in Netgear R7800
KERNEL BUG: BAD_PAGE_STATE in process appears here and there during intensive memory usage.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-10-31 16:48:04 +01:00
Henryk Heisig
0744b6a044 ipq806x: ArcherC2600: export usb power pins
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 16:40:54 +01:00
Henryk Heisig
dbf2feb2b3 ipq806x: ArcherC2600: devictree cleanup
add blank lines and use macros for GPIOs

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 16:40:28 +01:00
André Valentin
1465bebd74 ipq806x/nbg6817: add sysupgrade support
Add new way of flashing to mmc devices based on rootfs split with loop devices.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:47 +02:00
André Valentin
a0ed7af6c6 ipq806x/nbg6817: add support for ZyXEL NBG6817
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:46 +02:00
Rafał Miłecki
0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Felix Fietkau
a92f57599c ipq806x: add back end-of-UBI marker for a few factory images (FS#228)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-18 09:30:57 +02:00
Henryk Heisig
bcfb535730 ipq806x: C2600: change leds colour name
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Henryk Heisig
4bdf615878 ipq806x: add support for indicating the boot and upgrade state using four leds
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Pavel Kubelun
9677bfbb0f ipq806x: fix wlan mac for Netgear R7800
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-10-06 08:01:33 +02:00
dissent1
eb7307cb94 ipq806x: update Netgear R7800 device tree
-add spi pins
-move mdio and rgmii pinctrl from gmac and mdio into pinmux node
-add i2c4 pinctrl into rpm node
-add pin details into several nodes
-update gmac1 and gmac2 parameters
-update mdio phy0 and phy4 registers by ddwrt devs findings
-fix i2c4 pin drive-strengh
-remove pcie pins as it's already present in ipq8065 DT

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-09-30 10:15:23 +02:00
Mathias Kresin
1cd0a4c688 image: add KERNEL_SIZE to the default device vars
This reverts commit ec37a56587 and fixes
the underlying issue.
2016-09-13 19:36:41 +02:00