Commit graph

33 commits

Author SHA1 Message Date
Mathias Kresin
56b8ac1e86 treewide: consolidate upgrade state set
Set the (sys)upgrade state when sourcing the stage2 script instead of
setting the state for each target individual.

This change fixes the, due to a missing state set, not working upgrade
led on ath79 and apm821xx.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
INAGAKI Hiroshi
4645a6d318 ipq806x: add support for NEC Aterm WG2600HP
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.

Specification:

- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
  - RX, TX, NC, GND, Vcc from power connector side
  - baudrate: 115200 bps

Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
  /dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
  fw_setenv ipaddr "192.168.0.1"
  fw_setenv serverip "192.168.0.2"
  fw_setenv autostart "yes"
  fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
  bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 20:46:01 +02:00
Christian Mehlis
0c7e78930b ipq806x: add support for Compex WPQ864
Hardware highlights:
- SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU
- RAM: (512MB or 1GB) DDR3 System Memory
- Storage: 32MB NOR (Cypress S25FL256S1)
           256MB NAND (Micron MT29F2G08ABBEAH4)
- Ethernet: 5 x 1G via QCA8337N
- USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket
- PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared)
- SIM Card Slot: 2 x Slot
- Buttons: Reset Button
- LEDs: 18x, 8x GPIO controllable
- Buzzer

The correct amount of RAM will be passed by the bootloader.

In contrast to the documentation provided by Compex, the third PCIe
doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST
for PCIe0 and PCIe2.

So far, no one was able to get USB 3.0 working with the 1GB RAM version,
while it works fine for my 512MB version. Since USB 3.0 doesn't work with
the Compex firmware for the 1G variant either, it could be a hardware
issue with these boards.

OpenWrt will be installed to the NAND flash. Make sure to have a full
working image on the NOR flash. It will be the backup in case anything
goes wrong.

It has been observed that an image loaded via tftpboot might have
bitflips. Hence the extra step to create a crc32 checksum to allow to
compare the checksum with the one from the source file prior to flashing.

In all cases it is necessary to set the following u-boot parameter to an
empty (whitespace) value, to ensure that the chosen bootargs of the dts
isn't overwritten or set to bogus - not working - values:

  (IPQ) # set bootargs " "
  (IPQ) # set fsbootargs " "
  (IPQ) # saveenv

The sysupgrade image can be installed directly on flash using u-boot (put
jumper in JP13 (leave JP9 open) to boot from nand):

  (IPQ) # set serverip 192.168.1.20
  (IPQ) # set ipaddr 192.168.1.1

  (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin
  (IPQ) # crc32 0x42000000 $filesize

  (IPQ) # nand erase 0x1340000 0x4000000
  (IPQ) # nand write 0x42000000 0x1340000 $filesize

The initramfs image can be started using:

  (IPQ) # set fdt_high 0x48000000
  (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb
  (IPQ) # bootm 0x44000000

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-15 08:17:10 +01:00
John Crispin
b7f115f22a ipq806x: drop ipq40xx support
Signed-off-by: John Crispin <john@phrozen.org>
2018-03-14 19:04:50 +01:00
Stefan Lippers-Hollmann
4baffa02ce ipq806x: switch to full dual-boot for the nbg6817 sysupgrade support
Instead of writing to the currently booted partition set, this
implements full dual-boot support for sysupgrade by always writing to
the other, currently inactive, partition set and toggling the dualflag
after a successful flash.

The currently active/ booted partition set is determined by parsing
/proc/cmdline for its rootfs parameter (supplied by the DTS), instead
of reading from the 0:DUAL_FLAG mtd, in order to prevent (potentially)
bricking both partition sets.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-02-13 12:45:00 +01:00
Stefan Lippers-Hollmann
42fe7b3bbe ipq806x: request the first free loop device dynamically for the nbg6817 sysupgrade
Instead of hardcoding /dev/loop0, it's safer to query for the first
free loop device and assign that dynamically. While /dev/loop0 is a
reasonable assumption immediately following "losetup --detach-all",
detaching the mounted overlay is no longer strictly necessary once
dual-boot support has been added for the nbg6817.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-02-13 12:45:00 +01:00
Stefan Lippers-Hollmann
b36cf0be30 ipq806x: use absolute the device path in $kernel for the nbg6817 sysupgrade
Harmonize the variable usage for $kernel and $rootfs to always contain
the full device path, instead of just its basename.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-02-13 12:45:00 +01:00
Mathias Kresin
b6868e2f47 ipq806x: fix ZyXEL NBG6817 sysupgrade
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.

It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.

Fixes: 33f09cf151 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-18 07:22:37 +01:00
Sven Eckelmann
86e18f6706 ipq806x: add support for OpenMesh A42
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
  - 802.3af POE on Ethernet 1
  - 18-24v passive POE (mode B) on Ethernet 2

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 08:00:14 +01:00
Luis Araneda
7293499f71 ipq806x: Sort occurrences of boardame alphabetically
This restores the alphabetical sort that was present
before the renaming of boardname.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Luis Araneda
33f09cf151 ipq806x: convert to dt-based board-detection
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree

Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script

Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2018-01-13 07:33:03 +01:00
Stefan Lippers-Hollmann
9a221c6d69 ip806x: nbg6817: sysupgrade support both targets for kernel/ rootfs partitions
With this commit and the previous "nbg6817: don't hardcode the rootfs location
by using append-rootblock instead" applied, it is possible to boot- and
sysupgrade from both dual-boot sets (the primary mmcblk0p4+mmcblk0p5 or the
alternative mmcblk0p7+mmcblk0p8). However the sysupgrade support does not
toggle between both dual-boot sets between firmware upgrades so far.

The partition map of the eMMC used in the nbg6817 is:

Found valid GPT with protective MBR; using GPT.
Disk /dev/mmcblk0: 7471104 sectors, 3.6 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): XXX
Partition table holds up to 12 entries
First usable sector is 34, last usable sector is 7471070
Partitions will be aligned on 2-sector boundaries
Total free space is 1 sectors (512 bytes)

Number  Start (sector)    End (sector)  Size       Code  Name
   1              34            8225   4.0 MiB     FFFF  rootfs_data
   2            8226           16417   4.0 MiB     FFFF  romd
   3           16418           18465   1024.0 KiB  FFFF  header
   4           18466           26657   4.0 MiB     FFFF  kernel
   5           26658          157729   64.0 MiB    FFFF  rootfs
   6          157730          159777   1024.0 KiB  FFFF  header_1
   7          159778          167969   4.0 MiB     FFFF  kernel_1
   8          167970          299041   64.0 MiB    FFFF  rootfs_1
   9          299042          823329   256.0 MiB   FFFF  bu1
  10          823330         7471069   3.2 GiB     FFFF  bu2

rootfs_data is the ext4 formatted overlay of the OEM firmware, LEDE
ignores it due to its (too) small size.

romd/ bu1 are initialized with zeroes (0x00) and unused.

bu2 is formatted with ext4 and used for streamboost and other optional
functionality by the OEM firmware, it is reformatted during factory
resets of the OEM firmware.

header/ header_1 contains version information for the corresponding
vendor firmwares installed to kernel/rootfs or kernel_1/ rootfs_1, the
format hasn't been completely reverse engineered so far and remains
left untouched by LEDE:

V1.00(ABCS.2)C0:
 00000000  00 00 a7 74 01 32 f0 00  56 31 2e 30 30 28 41 42  |...t.2..V1.00(AB|
 00000010  43 53 2e 32 29 43 30 00  ff ff ff ff ff ff ff ff  |CS.2)C0.........|
 00000020  ff ff ff ff ff ff ff ff  00 00 d5 dc 4e 42 47 36  |............NBG6|
 00000030  38 31 37 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |817.............|
 00000040  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00000060  ff ff ff ff ff ff ff ff  ff ff ff ff 00 00 22 a3  |..............".|
 00000070  00 1c 70 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |..p.............|
 00000080  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00000800  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
 *
 00100000

V1.00(ABCS.5)C0:
 00000000  00 00 bf 94 01 46 d8 00  56 31 2e 30 30 28 41 42  |.....F..V1.00(AB|
 00000010  43 53 2e 35 29 43 30 00  ff ff ff ff ff ff ff ff  |CS.5)C0.........|
 00000020  ff ff ff ff ff ff ff ff  00 00 d6 5a 4e 42 47 36  |...........ZNBG6|
 00000030  38 31 37 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |817.............|
 00000040  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00000060  ff ff ff ff ff ff ff ff  ff ff ff ff 00 00 c0 2c  |...............,|
 00000070  00 1c 58 00 ff ff ff ff  ff ff ff ff ff ff ff ff  |..X.............|
 00000080  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
 *
 00010000  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
 *
 00100000

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2017-10-29 03:11:51 +01:00
Mathias Kresin
e4e984f2a0 treewide: use only board_name function to get name
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.

The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Mathias Kresin
f12a32630f treewide: use the generic board_name function
Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Matthias Schiffer
438dcbfe74
base-files: automatically handle paths and symlinks for RAMFS_COPY_BIN
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.

The list of binaries is also slightly cleaned up and duplicates are
removed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:26:32 +02:00
Matthias Schiffer
08a94ecaee
ipq806x: upgrade: fix RAMFS_COPY_*
RAMFS_COPY_* are moved to platform.sh toplevel. The unneeded
linksys_preupgrade function is removed, and the nand_do_upgrade call is
moved to platform_do_upgrade.

Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-11 17:19:23 +02:00
Ram Chandra Jangir
e178d51a04 ipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 board
This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.

Testing:
 *Tested on IPQ40xx AP-DK04.1-C1:
   a. NAND boot
   b. ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2017-06-07 06:33:33 +02:00
Christian Lamparter
1cb406d019 ipq806x: add ipq4019 fritz4040 support
This patch adds support for AVM FRITZ!Box 4040.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB Nanya NT5CC128M16IP
FLASH:	32 MiB MXIC MX25L25635FMI
ETH:	Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
	1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:	Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:	Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one WLAN and one WPS button
LEDS:	Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1. The SoC's serial port is right
	next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
	header for it. Use a multimeter to figure out the pinout!

This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.

Install Procedure:
 0. It's highly recommended to connect to the serial port.
    The serial settings are listed above.
 1. install a u-boot image for AVM Fritz!Box 4040
    (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
    <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
 2. upload the initramfs.itb image via tftp (u-boot listens to
    192.168.1.1 - use binary transfer mode!)
 3. connect to the FB4040 and use sysupgrade sysupgrade.bin
    to install the image.

Works:
	- Switch and Ethernet (99%)
        - Buttons (WLAN, WPS)
        - FLASH (1 x 32MiB NOR Chip)
        - WLAN2G and WLAN5G
        - CPUFREQ scaling
        - PRNG
        - serial
        - Crypto Accelerator
        - sysupgrade (Read the flash instructions to avoid bricking)
        - full LEDE Install (Read the flash instructions to avoid bricking)
	- LEDs (Power, WAN, Info (red and amber), LAN)
          The LEDs are connected to the QCA8075 LED ports.
	  The AR40xx driver contains a gpio-controller to
	  handle these special "GPIOs".
        - USB Both 3.0 and 2.0 ports
        - many packages from other ARMv7 boards
          (This does include the RaspberryPi Model 2!)
        - ...

Not planned:
	- WAN<->LAN short-cut
	- Qualcomm Secure Execution Environment
        - ...

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
2017-03-22 09:45:18 +01:00
Adrian Panella
d700c120bf ipq806x: EA8500 fix sysupgrade over stock firmware
When running sysupgrade for the first time over the second partition
(that still had stock firmware) the rootfs wasn't flashed as there
wasn't enough space.
This happend because stock also uses UBI, but the volume name wasn't
recognised and wasn't deleted before flashing.

Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-12-20 09:35:37 +01:00
Sebastian Quilitz
ae79c41286 ipq806x: add support for TP-Link Archer VR2600v
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.

It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.

To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.

Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
2016-11-24 22:37:40 +01:00
Felix Fietkau
b5ee86c4e5 ipq806x: remove device specific sysupgrade image checks
Replaced by image metadata

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-20 20:08:39 +01:00
Felix Fietkau
9d6d7d9a0e ipq806x: append metadata to images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-11-19 11:24:10 +01:00
André Valentin
1465bebd74 ipq806x/nbg6817: add sysupgrade support
Add new way of flashing to mmc devices based on rootfs split with loop devices.

Signed-off-by: André Valentin <avalentin@marcant.net>
2016-10-26 12:37:47 +02:00
Henryk Heisig
4bdf615878 ipq806x: add support for indicating the boot and upgrade state using four leds
Signed-off-by: Henryk Heisig hyniu@o2.pl
2016-10-15 11:36:50 +02:00
Alexis Green
c34f953fef ipq806x: Build image for Netgear Nighthawk X4 R7500v2
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-08-22 17:24:48 +02:00
Pavel Kubelun
823242185b ipq806x: add initial support for Netgear R7800
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
2016-06-22 19:32:06 +02:00
Adrian Panella
3d067c0132 ipq806x: base-files: add support for Linksys EA8500
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
2016-06-13 22:51:42 +02:00
Ash Benz
14515cc271 ipq806x/base-files: Add support for Archer C2600
Signed-off-by: Ash Benz <ash.benz@bk.ru>
2016-05-27 15:50:17 +02:00
John Crispin
78a6a9aec3 ipq806x: Add support for Netgear D7800
Signed-off-by: Tathagata Das <tathagata@alumnux.com>

SVN-Revision: 48360
2016-01-19 10:16:36 +00:00
Jonas Gorski
25ce154605 ipq806x: fix sysupgrade for AP148
AP148 uses lowercase name as boardname, so we need to use this in
platform.sh as well.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 48304
2016-01-18 10:46:58 +00:00
Rafał Miłecki
ffcb268437 ipq806x: add platform_pre_upgrade for sysupgrade
We're in process of cleaning nand_do_platform_check. Currently is leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.

The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.

This follows ar71xx, lantiq and partially bcm53xx.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 46945
2015-09-15 16:05:10 +00:00
Jonas Gorski
8b4df1efd5 ipq806x: add support for Netgear Nighthawk X4 R7500
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.

Known issues:
 * 5 GHz wifi not working - there is no quantenna driver
 * One of the USB ports is not working

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46796
2015-09-04 14:46:06 +00:00
Jonas Gorski
89815d4645 ipq806x: build images and add sysupgrade support for AP148
Add full ubi and sysupgrade images for AP148 and add sysupgrade support
for ipq806x to allow updating the current installation.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 46789
2015-09-04 14:45:00 +00:00