The 5GHz radio of this device uses an mt7610e PCI-E chip, which has
been recently started to be supported.
mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
mt76x0e 0000:01:00.0: ASIC revision: 76100002
mt76x0e 0000:01:00.0: Firmware Version: 0.1.00
mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specify firmware partition format to denx,uimage in compatible DTS property.
2 uimage-fw partitions found on MTD device firmware
Creating 2 MTD partitions on "firmware":
0x000000000000-0x00000017f72b : "kernel"
0x00000017f72b-0x000000f70000 : "rootfs"
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Flash partitions were moved under partition table node, but addition of
compatible property was omitted which lead to following boot failure:
VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
1f00 16384 mtdblock0
(driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Fixes: e4d9217f (ramips: improve BDCOM WAP2100-SK support)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since we do nothing special for mxs based boards,
we can simply use the generic existing code.
We just need to convert scripts to use the DT
compatible strings.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Update the OpenVPN package to version 2.4.6, refresh patches and drop
menuconfig options which are not supported upstream anymore.
Also fix the x509-alt-username configure flag - it is not supported
by mbedtls and was syntactically wrong in the Makefile - and the
port-share option which has been present in menuconfig but not been
used in the Makefile.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The 5 GHz radio of this device uses an mt7610e pci-e chip, which has
been recently added support.
Tested on the actual device as AP and client, TCP throughput ~90 Mbps
U/D.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Add support for UniElec U7621-06 variant with 512MB RAM and 64MB flash.
Additional specs are below:
CPU: MT7621 (880Mhz)
Bootloader: Ralink U-Boot
Flash: 64MB
- U-Boot identifies as Macronix MX66L51235F
- kernel identifies as MX66L51235l (65536 Kbytes)
RAM: 512MB
Rest of the details as per commit 46ab81e405 ("ramips add support for
UniElec U7621-06")
Signed-off-by: Nishant Sharma <nishant@unmukti.in>
[use generic board detection, add firmware partition compatible, extend
firmware partition to use all of the remaining flash space, add a
maximum image size matching the firmware partition size]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the generic board detection for the board instead of the target
specific one. Mark the sysupgrade image compatible with the former used
userspace boardname to allow an upgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit adds support for the ROSINSON WR818 WiFi-Router
SoC: Qualcomm Atheros QCA9563,
FLASH: Winbond W25Q128FV 16MBytes,
WiFi: QCA9563 b/g/n 3x3 450Mbit/s,
USB: 1x USB 2.0 Type A, 1x USB2.0 Type C,
IN: WPS/Reset button GPIO1,
OUT: Power LED red, Internet LED red, WLAN LED red,
LAN1 LED red, LAN2 LED red, System LED red,
UART: RX-GPIO18, TX-GPIO22,
Tested and working:
- Ethernet (LAN + WAN)
- WiFi
- OpenWRT sysupgrade
- Button
- LEDs
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.1.1
- Go to "Administration" -> "Firmware Upgrade"
- Upload the OpenWrt sysupgrade image
Signed-off-by: Rosy Song <rosysong@rosinson.com>
The board doesn't come in different flash type flavours, hence there is
no need to keep a dtsi + dts for this purpose.
While at it, fix some whitespace issues.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The RavPower WD03 is a mt7620n based baord. With the change applied, I2C
should work now with the RavPower WD03.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit adds firmware partition compatible for the
TP-Link Archer C58 v1 and Archer C59 v1.
Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds firmware partition compatible for the
OCEDO Raccoon and OCEDO Koala.
Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specify firmware partition format (denx,uimage) by compatible string
for ELECOM WRC-300GHBK2-I.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
With ed25e3ac02 ("ramips: fix some clocks in mt7621.dtsi") the
cpuclock node was dropped from the mt7621.dtsi without removing the
references to this node from the GB-PC1/PC2 dts files.
Remove them now, to fix the build error.
Signed-off-by: Mathias Kresin <dev@kresin.me>
It has to be <board>:<colour>:<function> and is expected exactly this
way by the userspace scripts.
While at it, fix some whitespace issues in the dts file and rename the
flash node as required upstream.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Multicast ARL entries can have multiple destination ports. Get and dump
all destination ports of each entry, not just the lowest.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
Use the generic board detection instead of the target specific one as
all recent additions are doing.
Setup the USB led via devicetree (a58535771f) and include the required
driver by default. Merge the led userspace setting with an existing
identical case.
Use the wps led for boot status indication.
Move the partitions into a partition table node (6031ab345d) and drop
needless labels. Drop misplaced cells properties (53624c1702).
Cleanup the pinmux and only switch pins to gpio functions which a
referenced as gpio in the dts.
Match the maximum image size with the size of the firmware partition.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The sd function of the nd_sd group configures two of the groups pins as
gpios. The pins are used as PCIe reset/power.
Due to the driver load order, the pins are configured way to late if
triggered by the sd-card driver.
To not introduce another kind of driver load order dependency and
configure the pins as early as possible, means during pinmux driver
load.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In case the nd_sd group is set to the sd-card function, Pins 45 + 46 are
configured as GPIOs. If they are blocked by the sd function, they can't
be used as GPIOs.
Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit dcdc6d9dad.
Even if described this way in the datasheet, it causes a bootloop on a
RT-N56U (v1):
of-flash 1c000000.nor-flash: do_map_probe() failed for type cfi_probe
of-flash 1c000000.nor-flash: do_map_probe() failed
VFS: Cannot open root device “(null)” or unknown-block(0,0): error -6
Fixes: FS#1930
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the generic board detection instead of the target specific one as
all recent additions are doing.
Add the wireless led according the gpio number from the datasheet.
Rename the board part of the leds to match the name used for the
compatible string. Finally, do not hijack the wps led for boot status
indication longer than necessary.
Merge userspace config into existing cases.
Include the manufacture Name in the dts model string.
Signed-off-by: Mathias Kresin <dev@kresin.me>
dfa4ede interface: fix return code of __interface_add()
a82a8f6 netifd: fix resource leak on error in netifd_add_dynamic()
fa2403d config: fix resource leaks on error in config_parse_interface()
85de9de interface: fix memory leak on error in __interface_add()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Remove the source-only flag from ath79, its supposed to replace ar71xx after next stable release but buildbots are not currently generating images for it.
So in order to expand testing as much as possible and prepare for moving to ath79 lets enable the buildbots to actually build the target.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Lava LR-25G001 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN)
- 2x external, detachable antennas
- 1x USB 2.0
- UART (J3) header on PCB (57600 8n1)
- 8x LED (3x GPIO-controlled), 2x button
- JBOOT bootloader
Known issues:
- Work only three Gigabit ports (3/5, 1 WAN and 2LAN)
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Some boards have external switches different than mt7530.
This patch allow to use mdio-mode without 0x1f register.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Driver crash when 'phydev->adjust_link' isn't provided.
This patch check if 'phydev->adjust_link' exist before
call the method.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
For a long time the mt7621 uses a fixed cpu clock which causes a problem
if the cpu frequency is not 880MHz.
This patch fixes the cpu clock calculation and adds the cpu/bus clkdev
which will be used in dts.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
The memc node from mt7621.dtsi has incorrect register resource.
Fix it according to the programming guide.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>