ramips: add support for Lava LR-25G001
The Lava LR-25G001 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN) - 2x external, detachable antennas - 1x USB 2.0 - UART (J3) header on PCB (57600 8n1) - 8x LED (3x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - Work only three Gigabit ports (3/5, 1 WAN and 2LAN) Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This commit is contained in:
Pawel Dembicki
John Crispin
parent
b85fe43ec8
commit
20b09a2125
7 changed files with 210 additions and 3 deletions
|
|
@ -195,6 +195,10 @@ kn_rf|\
|
|||
kng_rc)
|
||||
set_wifi_led "$boardname:green:wifi"
|
||||
;;
|
||||
lava,lr-25g001)
|
||||
ucidef_set_led_netdev "wlan2g" "WiFi 2.4GHz" "$boardname:green:wlan2g" "wlan1"
|
||||
ucidef_set_led_netdev "wlan5g" "WiFi 5GHz" "$boardname:green:wlan5g" "wlan0"
|
||||
;;
|
||||
linkits7688)
|
||||
ucidef_set_led_wlan "wifi" "wifi" "linkit-smart-7688:orange:wifi" "phy0tpt"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -353,6 +353,7 @@ ramips_setup_interfaces()
|
|||
ucidef_add_switch "switch0" \
|
||||
"4:lan" "6@eth0"
|
||||
;;
|
||||
lava,lr-25g001|\
|
||||
tew-691gr|\
|
||||
tew-692gr|\
|
||||
wlr-6000)
|
||||
|
|
@ -475,7 +476,8 @@ ramips_setup_macs()
|
|||
;;
|
||||
dlink,dwr-116-a1|\
|
||||
dlink,dwr-118-a2|\
|
||||
dlink,dwr-921-c1)
|
||||
dlink,dwr-921-c1|\
|
||||
lava,lr-25g001)
|
||||
wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000)
|
||||
lan_mac=$(macaddr_add "$wan_mac" 1)
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -56,7 +56,8 @@ case "$FIRMWARE" in
|
|||
case $board in
|
||||
dlink,dwr-116-a1|\
|
||||
dlink,dwr-118-a2|\
|
||||
dlink,dwr-921-c1)
|
||||
dlink,dwr-921-c1|\
|
||||
lava,lr-25g001)
|
||||
wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000)
|
||||
wifi_mac=$(macaddr_add "$wan_mac" 1)
|
||||
jboot_eeprom_extract "config" 0xE000
|
||||
|
|
|
|||
|
|
@ -295,7 +295,8 @@ platform_check_image() {
|
|||
dlink,dwr-116-a1|\
|
||||
dlink,dwr-118-a2|\
|
||||
dlink,dwr-921-c1|\
|
||||
dwr-512-b)
|
||||
dwr-512-b|\
|
||||
lava,lr-25g001)
|
||||
[ "$magic" != "0404242b" ] && {
|
||||
echo "Invalid image type."
|
||||
return 1
|
||||
|
|
|
|||
182
target/linux/ramips/dts/LR-25G001.dts
Normal file
182
target/linux/ramips/dts/LR-25G001.dts
Normal file
|
|
@ -0,0 +1,182 @@
|
|||
/dts-v1/;
|
||||
|
||||
#include "mt7620a.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "lava,lr-25g001", "ralink,mt7620a-soc";
|
||||
model = "LAVA LR-25G001";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status;
|
||||
led-failsafe = &led_status;
|
||||
led-running = &led_status;
|
||||
led-upgrade = &led_status;
|
||||
};
|
||||
|
||||
gpio-keys-polled {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_status: status {
|
||||
label = "lava,lr-25g001:green:status";
|
||||
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi2g {
|
||||
label = "lava,lr-25g001:green:wifi2g";
|
||||
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi5g {
|
||||
label = "lava,lr-25g001:green:wifi5g";
|
||||
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
usbpower {
|
||||
gpio-export,name = "usbpower";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
mx25l12805d@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "jboot";
|
||||
reg = <0x0 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@10000 {
|
||||
label = "firmware";
|
||||
reg = <0x10000 0xfe0000>;
|
||||
};
|
||||
|
||||
config: partition@ff0000 {
|
||||
label = "config";
|
||||
reg = <0xff0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ohci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ðernet {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;
|
||||
|
||||
port@5 {
|
||||
status = "okay";
|
||||
phy-mode = "rgmii";
|
||||
mediatek,fixed-link = <1000 1 1 1>;
|
||||
};
|
||||
|
||||
mdio-bus {
|
||||
status = "okay";
|
||||
mediatek,mdio-mode = <1>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
phy-mode = "rgmii";
|
||||
qca,ar8327-initvals = <
|
||||
0x04 0x87300000 /* PORT0 PAD MODE CTRL */
|
||||
0x0c 0x00000000 /* PORT6 PAD MODE CTRL */
|
||||
0x7c 0x0000007e /* PORT0_STATUS */
|
||||
0x94 0x00000000 /* PORT6_STATUS */
|
||||
|
||||
>;
|
||||
};
|
||||
|
||||
phy1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
phy2: ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
phy3: ethernet-phy@3 {
|
||||
reg = <3>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
mt76x0e@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mtd-mac-address = <&config 0xe07e>;
|
||||
mtd-mac-address-increment = <(2)>;
|
||||
mediatek,mtd-eeprom = <&config 0xe08a>;
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "uartf", "i2c";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -352,6 +352,21 @@ define Device/microwrt
|
|||
endef
|
||||
TARGET_DEVICES += microwrt
|
||||
|
||||
define Device/lava_lr-25g001
|
||||
DTS := LR-25G001
|
||||
DEVICE_TITLE := LAVA LR-25G001
|
||||
DLINK_ROM_ID := LVA6E3804001
|
||||
DLINK_FAMILY_MEMBER := 0x6E38
|
||||
DLINK_FIRMWARE_SIZE := 0xFE0000
|
||||
KERNEL := $(KERNEL_DTB)
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := mkdlinkfw | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := mkdlinkfw | pad-rootfs | mkdlinkfw-factory
|
||||
DEVICE_PACKAGES := jboot-tools kmod-usb2 kmod-mt76 kmod-mt76x0-common \
|
||||
kmod-mt76x0e
|
||||
endef
|
||||
TARGET_DEVICES += lava_lr-25g001
|
||||
|
||||
define Device/miwifi-mini
|
||||
DTS := MIWIFI-MINI
|
||||
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
||||
|
|
|
|||
|
|
@ -1,3 +1,4 @@
|
|||
CONFIG_AR8216_PHY=y
|
||||
CONFIG_ARCH_BINFMT_ELF_STATE=y
|
||||
CONFIG_ARCH_CLOCKSOURCE_DATA=y
|
||||
CONFIG_ARCH_DISCARD_MEMBLOCK=y
|
||||
|
|
@ -57,6 +58,7 @@ CONFIG_DTB_RT_NONE=y
|
|||
# CONFIG_DTB_VOCORE2 is not set
|
||||
CONFIG_DTC=y
|
||||
CONFIG_EARLY_PRINTK=y
|
||||
CONFIG_ETHERNET_PACKET_MANGLE=y
|
||||
CONFIG_FIXED_PHY=y
|
||||
CONFIG_GENERIC_ATOMIC64=y
|
||||
CONFIG_GENERIC_CLOCKEVENTS=y
|
||||
|
|
|
|||
Loading…
Reference in a new issue