* use build step mktplinkfw with extra arguments
* remove now unused mktplinkfw-chn-v2
* use Device/tplink
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47175
Allow to pass extra arguments to mktplinkfw step. Some board requires
an extra argument to create a valid image.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47174
These profiles covered by new image/Makefile descriptions. Only the old format uses
MultiProfile macro
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47173
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]
SVN-Revision: 47036
QCA9563 and QCA9561 are two series of Qualcomm SoC Dragonfly. The only different
is QCA9563 w/o internal switch. It has one GMAC with SGMII interface. But they
have the same device ID(0x1150). So they share the same codes.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
SVN-Revision: 46971
This patch adds kernel and userspace support for the Ubiquiti Networks airGateway Pro.
Signed-off-by: Matthew Reeve <mreeve at tenxnetworks.com>
SVN-Revision: 46961
This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46934
The GPIO pins for "POE passthrough" of Ubiquiti Nanostation models are the
following:
* Ubiquiti Nanostation M XM: Pin 8
* Ubiquiti Nanostation M XW: Pin 2
The previous definition of the pins was mixed up between XM and XW model.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46922
To make the lzma-loader build with binutils 2.25.1 it is needed to
remove the .MIPS.abiflags section otherwise I get the following compile
error:
mips-openwrt-linux-musl-objcopy -O binary -R .reginfo -R .note -R .comment -R .mdebug -S loader loader.bin
mips-openwrt-linux-musl-objcopy: Warning: Writing section `.text' to huge (ie negative) file offset 0xffffffff80a00000.
mips-openwrt-linux-musl-objcopy:loader.bin[.text]: File truncated
This should close#20487.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46893
Increase space for kernel and also introduce a 8M flash target into the
Makefile.
Signed-off-by: Attila Lendvai <attila@lendvai.name>
SVN-Revision: 46862
According to the AR7242 datasheet section 2.8, AR724X CPUs use a 40MHz
input clock as the REF_CLK instead of 5MHz.
The correct CPU PLL calculation procedure is as follows:
CPU_PLL = (DIV * REF_CLK) / REF_DIV / 2.
This patch is compatible with the current calculation procedure with default
DIV and REF_DIV values.
Test on both AR7240, AR7241 and AR7242.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46856
This adds full support (sans sysupgrading from vendor firmware) for the COMFAST
CF-E316N v2 (aka CF-E316V2, CF-E316N-V2 and CF-E316Nv2.0, no FCC ID) by
Shenzhen Four Seas Global Link Network Technology Co., Ltd (this company is
actively refusing to provide GPL'd sources for the OpenWrt version they ship
with the device, damn them).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 46852
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds support for TP-Link TL-WDR6500 v2.
The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.
SVN-Revision: 46663
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds flash layout parser for TP-Link firmwares which have a 64kb
bootloader.
This is used for TP-Link TL-WDR6500 v2.
SVN-Revision: 46662
Instead of each target defining it the same, move the KDIR_TMP
definition to include/image.mk. In addition Image/Build/SysupgradeNAND
already requires KDIR_TMP to be set, so it makes sense to have it
globally defined.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46592
Variables dependend on JFFS2_BLOCKSIZE and NANDBLOCK_SIZE are used
for template generation, so need to be present before inclusion of
image.mk in target image Makefiles.
So move all declarations to before any includes.
Fixes: r42878 ("image.mk: clean up and parallelize mkfs calls")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46564
The generic kernel cmdline parser ignores argv[0], this caused a
regression for all lzma-loader based boards with linux 4.1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 46544
This patch adds support for the Onion Omega.
https://onion.io/omega
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: Boken Lin <bl@onion.io>
Tested-by: Jacky Huang <huangfangcheng@163.com>
SVN-Revision: 46458
There are a few NETGEAR devices which don't terminate the model name in the
ART with a NUL byte, at least some NETGEAR WNDR3700v2. The current awk
expression doesn't match 0xFF bytes, so AR71XX_MODEL contains lots of
trailing 0xFF garbage in this case.
Fix this by matching for the first non-printable character and explicitly
setting LC_CTYPE=C (probably not strictly necessary on OpenWrt, but will
definitely work like this, even when awk supports locales and LANG is set).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46455
As r46245 disabled the board.bin template workaround, 5GHz wifi stopped working
on these devices. This adds them to the calibration data loading introduced in
r46244 and thus makes 5GHz work again for these devices.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>
SVN-Revision: 46415
To improve reproducibility, prevent the inclusion of timestamps
in the gzip header.
Signed-off-by: Reiner Herrmann <reiner@reiner-h.de>
SVN-Revision: 46361
In fb6f62e97733312053ab593fcf68eea47a21169e several settings
are set on the ethernet device, but they are not working.
Fix Ethernet by setting the right values.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 46281
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46280
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.
This patch makes all boards use the first method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46244
This device is identical to the TL-WR740N v5, it even uses the same HWID (which
wasn't the case for older TL-WR741ND revisions).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46238
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46234
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46206
r45954 ("ar71xx: fix 100/10mbps ethernet link issues on mynet range
extender") introduced a pdata based modification of the tx_clk_dly. But it
was not checked if pdata actually existed. This caused a page fault on all
devices which didn't have at803x_platform_data specified for an at803x
based device.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46200
Update firmware name and md5sum. MAC-address location remains
unchanged from previous version.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46196
- it should be BOARDNAME instead of BOARD_NAME
- kernel partition should be padded to 1536k (somehow this padding was lost in translation to BuildCode in bc797c73f6328941b2194d144385655ad9297e7c)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 46193
EPG5000 uses ath79 nvram functions, but does not select it. This breaks
build if no other board support enabling nvram support is selected.
Closes#19952.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46190
r46161 updated headers also touched by it, so it needed to be refreshed
as well.
Closes#20033.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46165
TP-Link ships wr740n v5.0 to Romania (so probably everywhere except
China) with 4 MB flash and 32 MB memory (confirmed by their local
support). This patch adds support for the v5.0 clone of v4, i just
tested it on my own v5.0 router and it works.
Signed-off-by: Daniel Petre <daniel.petre@posteo.net>
SVN-Revision: 46115
The hardware should be almost the same as TL-WR720N-v3. WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>". Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 46046
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>
SVN-Revision: 46044
