Let's not confuse users about the revisions of their devices when we can
easily avoid it.
Not tested on real hardware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49107
Instead of adding the space when combining $model and $hwver, add the space
to the beginning of $hwver, so the resulting string won't end with a space
when $hwver is set to the empty string.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49106
There's no reason for us to be more lenient than the stock firmware, so
better check the HWREV as well to avoid bricked devices.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49105
This patch provides full GPIO support for WNR2200 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49101
Fix for invalid/random/duplicate WLAN MAC address in WNR2200.
Permanent platform MAC is calculated and assigned during system startup.
WLAN MAC follows wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49100
This patch adds support for the TP-Link TL-WR841N/ND to trunk. It is
similar to the already supported v10 - see [1]. I have added support
based on that topic; in the meantime it has been confirmed working
(see the forum thread, and also [2]).
Signed-off by Stijn Segers <francesco.borromini@inventati.org>
[1]: https://forum.openwrt.org/viewtopic.php?id=61309
[2]: https://forum.openwrt.org/viewtopic.php?id=63657
SVN-Revision: 49099
On most platforms the cmdline is supplied by the loader to the kernel.
When using an elf loader with cmdline the size is bloated by 512k.
For loader-elf platforms like the cpe510 better use loader-elf but patch
the cmdline into the kernel.
wdr1043: Tested loader still works using sysupgade image.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49080
The loader decompress a lzma compressed kernel. Some bootloaders
only support elf files like the tplink cpe510
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49079
This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49076
Not all mach-* files set all boards correctly in ETH_CFG. They depend on
some preset values by u-boot which were not previously modified by
ath79_setup_qca955x_eth_cfg. Avoiding to modify them in this function keeps
it backward compatible for these boards.
This reverts commit 119b8ab2c2eac237ec4e9c4d0ed53df22b5c6978.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49072
The default delays RXD 3. RDV 3, TXD 0, TXE 0 doesn't seem to work for some
boards. These boards depend on the preset values of u-boot which may
differ.
This reverts commit f2d4bb96b62512caa161dcc2867c91692fb16a38.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49071
The MR1750 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR1750 can be used instead.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49070
The MR900 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR900 can be used instead.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49069
Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3
and WNR612v2.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49051
The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.
This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.
Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49031
The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.
This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.
Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49030
Some u-boot versions for QCA955x change the delays based on the link speed
during boot. This usually breaks the support of other linkspeeds when
OpenWrt is booted. It also conflicts with the
at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own
values in QCA955X_GMAC_REG_ETH_CFG.
The default RGMII values from the Atheros u-boot are currently used to
preset the existing mach files. These may have to be adjusted for boards
using different values but which are not currently set them explicitely in
OpenWrt.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Christian Beier <cb@shoutrlabs.com>
Cc: Chris R Blake <chrisrblake93@gmail.com>
Cc: Benjamin Berg <benjamin@sipsolutions.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Dirk Neukirchen <dirkneukirchen@web.de>
Cc: Christian Mehlis <christian@m3hlis.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 49029
Some u-boot versions for QCA955x set currently not cleared bits depending
on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c
file is responsible to select the correct configuration bits and thus the
ath79_setup_qca955x_eth_cfg has to clear the unset.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49028
Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 48937
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48924
This patch add speed_mask parameter to Ethernet port LED initialization
during system startup. LEDs are configured to show amber light for 10 Mbps
link and green for 100 Mbps as described on device label.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48923
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
Enable platform-supplied WLAN LED name for ath9k device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48879
This patch moves the OOLITE profile code into the overarching Gainstrong
profile and deletes the old single profile file.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 48866
The ubdev01 profile defines its own MTDPARTS with smaller firmware
partition, so give it its own UBNT_BOARD in mkfwimage.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48828
This is the first patch of a series of three to tidy up the profiles for
Gainstrong devices. Right now there are two Gainstrong profiles, each
for a single device built by this manufacturer. This patch renames the
MiniBox profile to Gainstrong and updates the copyright notice.
The series applies cleanly to current trunk. Resent with the architecture in
the subject, forgot that the first time.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 48797
Fix for invalid/random WLAN MAC address in WNR612v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48779
Netgear WNR612v2 has no USB port yet default system image
includes USB kernel modules. This patch fixes that.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48778
Fix for invalid/random WLAN MAC address in WNR2000v3. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48777
- remove the suffix (N, ND) to indicate that the image is for all
WR841-models
- some of these models have a "N"-suffix, others have (ND)-suffix,
but the boards are the same - only difference is the detachable
antenna on "D"-models
- discussed this idea to remove the suffix in IRC with jow and Borromini
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
SVN-Revision: 48767
Netgear WNR2000v3 has no USB port yet default system image
includes USB kernel modules. This patch fixes that.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48701
This reverts commit r48276.
This can overwrite the caldata_backup partition, so the layout needs to
be changed in a different way.
Thanks to Arjen de Korte for spotting the issue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48456
According to the calling convention of the o32 ABI the caller
function must reserve stack space for $a0-$a3 registers in case
the callee needs to save its arguments.
The assembly code of the loader does not reserve stack space for
these registers thus when the 'loader_main' function needs to save
its arguments, those will be stored in the 'workspace' area instead
of the stack.
Because the workspace area is also used by other part of the code, the
saved register values gets overwritten and this often leads to failed
kernel boots.
Fix the code to reserve stack space for the registers to avoid this
error.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 48279
Change MTD on WNDR4300 and WNDR3700v4 to fully utilize the 128MB flash.
Credit to @Tuochenlyu on GitHub.
Signed-off-by: Chris Marchesi <chrism@vancluevertech.com>
SVN-Revision: 48276
Fully reset the chip like on a full up/down, but without the PHY
statemachine restart.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48228
My last bugfix (r47538) introduced a new bug in wndr3700_board_detect
(again...).
Assigning the result of ar71xx_get_mtd_offset_size_format to the model
variable before stripping of garbage using awk will cause all NUL bytes to
be removed before awk is applied, leading to model strings like
"NETGEAR WNDRMACv2NETGEAR", where a NUL byte after the v2 is supposed to
terminate the string.
Fix by calling ar71xx_get_mtd_offset_size_format twice, once piping to awk
directly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48075
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
