Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree
compatible string directly. Always use the board_name function to get
the board name.
The admswconfig package still reads /proc/cpuinfo directly. The code
looks somehow broken and the whole adm5120 which uses this package
looks unmaintained. Leave it as it is for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.
The list of binaries is also slightly cleaned up and duplicates are
removed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
RAMFS_COPY_* are moved to platform.sh toplevel. The unneeded
linksys_preupgrade function is removed, and the nand_do_upgrade call is
moved to platform_do_upgrade.
Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.
Testing:
*Tested on IPQ40xx AP-DK04.1-C1:
a. NAND boot
b. ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This patch adds support for AVM FRITZ!Box 4040.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
Not planned:
- WAN<->LAN short-cut
- Qualcomm Secure Execution Environment
- ...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
When running sysupgrade for the first time over the second partition
(that still had stock firmware) the rootfs wasn't flashed as there
wasn't enough space.
This happend because stock also uses UBI, but the volume name wasn't
recognised and wasn't deleted before flashing.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
AP148 uses lowercase name as boardname, so we need to use this in
platform.sh as well.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48304
We're in process of cleaning nand_do_platform_check. Currently is leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
This follows ar71xx, lantiq and partially bcm53xx.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46945
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.
Known issues:
* 5 GHz wifi not working - there is no quantenna driver
* One of the USB ports is not working
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46796
Add full ubi and sysupgrade images for AP148 and add sysupgrade support
for ipq806x to allow updating the current installation.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46789
