Commit graph

19451 commits

Author SHA1 Message Date
Daniel Gimpelevich
379fe50672 ramips: fix gigabit switch PHY access on MDIO
When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.

Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Daniel Gimpelevich
5a6229a93d ramips: remove superfluous & confusing DT binding
Mediatek has a reference platform that pairs an MT7620A with an MT7530W,
where the latter responds on MDIO address 0x1f while both chips respond on
0x0 to 0x4. The driver special-cases this arrangement to make sure it's
talking to the right chip, but two different ways in two different places.
This patch consolidates the detection without the current requirement of
both tests to be separately satisfied in the DTS.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Daniel Gimpelevich
f72fa883b3 ramips: add support for Edimax BR-6478AC v2
Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie.
Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated.

Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Macronix MX25L6405D
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7612E 5GHz 802.11ac
- Switch: Mediatek MT7530W Gigabit Switch
- USB: Yes 1 x 2.0

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
4. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2018-08-06 07:05:37 +02:00
Alex Maclean
6031ab345d ramips: move partitions into partition table node
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
2018-08-04 08:39:35 +02:00
Mathias Kresin
6dd94c2781 ramips: unify partition node names in dts files
Use partition@ as name for all partition nodes. Add a label where
necessary.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
bfd65fc4ab ramips: fix whitespace and comment issues in dts
Fix space vs. tabs issue and trainling whitespaces. Use C style
comments or drop the comments if they explain what is already to see in
the devicetree parameters.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
53624c1702 ramips: fix dtc warnings
Fix individual boards dtc warnings or obvious mistakes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
6384e0d16a ramips: fix hnat dtc warning
The hardware NAT node has the same reg/unit as the ethernet node. One
of them need to be a child of the other.

Make the hardware NAT node a child of the ethernet node since the it
"reference" the netdev in its properties.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
f9b8328d79 ramips: fix pci/pcie related dtc warnings
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.

Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.

Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.

If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.

Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.

Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
d8e7a526a3 ramips: use ralink,nr-gpio instead of ralink,num-gpios
Since commit c1e7738988f5 ("checks: add gpio binding properties check")
dtc treats any *-gpios and *-gpio property as phandle at least during
checks. The only whitelisted property is nr-gpio.

Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false
positive warnings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
1bad2b74ae ramips: fix cpu interrupt controller dtc warnings
The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
b9dbf3f3c8 ramips: fix cpu related dtc warnings
We need a reg property if we are using a unit address.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
René van Dorst
0ae9396556 treewide: convert gpio-export to platform driver
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.

gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.

Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Mathias Kresin
1d18a14a90 ath79: really fix TP-Link Archer C7 v2 MAC address
Revert 290c54473e ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address")
which obviously aims to have a distinct MAC address per interface.

Unfortunally it doesn't match what is used by the stock firmware and we
shouldn'z use MAC Adresses not reserverd for/assigned to a particular
board.

The correct MAC adress increments for this board are:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

Fixes: FS#408

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Koen Vandeputte
f960490fc8 kernel: bump 4.14 to 4.14.60
Refreshed all patches

Removed upstreamed patches:
- 500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-03 16:10:38 +02:00
Koen Vandeputte
4ec4dd2a11 kernel: bump 4.9 to 4.9.117
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-03 16:10:38 +02:00
Jonas Gorski
2308b87204 brcm63xx: switch to 4.14
Kernel 4.14 support has been present for quite some time, so let's give
it wider testing.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:49:18 +02:00
Jonas Gorski
15cb65dad7 brcm63xx: drop b43 from devices with unsupported wifi
The internal wifi isn't supported, so drop b43 from devices that only
have it.

Fixes FS#1698
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:43:52 +02:00
Jonas Gorski
8cb8d70fea brcm63xx: copy SR102 support patch to 4.14 as well
It seems to have been missed when the patch was accepted.

Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:43:52 +02:00
Jonas Gorski
bc1c706bb3 brcm63xx: drop bogus SPROM section from SR102
The integrated SoC wifi will likely never be supported, and if,
it will go through DT with the sprom contents there.

Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-08-02 08:43:52 +02:00
Andrew Cameron
bae927c551 ar71xx: add support for TP-LINK CPE510 V2.0
Adds Support for the TP-LINK CPE510 V2.0 by TP-Link.
The hardware is almost the same as the CPE510 V1.0
Follow the same processes as for the CPE510 V1.0

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2018-08-02 07:49:26 +02:00
Jo-Philipp Wich
b9bd3285c7 Revert "ar71xx: ag71xx: Prevent kernel oops for board def"
This reverts commit 7a3e133751.

This change reportedly breaks connectivity on some ar71xx devices, so
revert it for now.

Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 22:34:22 +02:00
Jo-Philipp Wich
33dbe2c55d Revert "ar71xx: ag71xx: Add connect message: fixed phy"
This reverts commit 0b9f4e8808.

This change reportedly breaks connectivity on some ar71xx devices, so
revert it for now.

Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 22:31:37 +02:00
Jo-Philipp Wich
9ebf596386 Revert "ar71xx: ag71xx_phy: Fix compilation for debug messages"
This reverts commit 2655fbe8ef.

The patch introduces syntax errors, revert it for now.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-01 22:31:14 +02:00
Daniel F. Dickinson
0b7a9688ce ar71xx: cr3000: cleanup board definition
1) Add comments so it's clear why we did things; this may prevent
   someone (e.g. me) from sinking time into fixing things that
   aren't broken and/or were done for reason.

2) Drop mdio 0 probe/register; we don't use ag1xx mdio bus 0.

3) Cosmetic reording of some code (tested) that makes the defintion
   more clear.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:54 +02:00
Daniel F. Dickinson
b6c8bc0981 ar71xx: cr3000: Use correct company name
It's 'PowerCloud Systems' not 'PowerCloud'.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:54 +02:00
Daniel F. Dickinson
e38520cd50 ar71xx: cr3000: Drop support for defunct cloud
The CR3000 stock firmware is now irrelevant as it required a now defunct
cloud service.  Therefore only build images that use the entire flash
(overwriting stock firwmare-specific partitions that no longer matter),
previously called 'nocloud' images.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:54 +02:00
Daniel F. Dickinson
60cf71ede7 ath79: Forward port support for CR3000
The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct
NaaS offering.  It was previously supported under the ar71xx branch and
this forward ports that support with some notable differences:

1) Since reverting to stock firmware is now irrelevant there is is only
a single openwrt image generated which uses the entire flash rather than
preserving PowerCloud-specific partitions that are unneeded to openwrt--
those partitions will be erased and used by the openwrt image.

2) Rather than use a non-standard probe order for the ethernet devices,
this image uses a set of 'ip link set ethX name ethY' commands very early
in preinit (before the network is used at all), in order to have the the
switch and Wan use the same ethernet names as in previous images.

3) /etc/config/wireless will need to be regenerated as the path to the
wireless device has changed due to differences in ath79 DT for ar93x
compared to ar71xx images.

4) eth0 is wan and eth1 is lan (switch)

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-08-01 11:23:53 +02:00
Koen Vandeputte
fec8fe8069 kernel: bump 4.9 to 4.9.116
Refreshed all patches

Remove upstreamed patches.
- 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
- 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch
- 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- 900-gen_stats-fix-netlink-stats-padding.patch

Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

This patch has been slightly altered to compensate for a new helper function
introduced in later kernels.

Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9

Compile-tested on: ar71xx, bcm2710
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-01 09:46:59 +02:00
Stijn Tintel
77e3e706ce kernel: add missing ARM64_SSBD symbol
In 4.14.57, a new symbol for Spectre v4 mitigation was introduced for
ARM64. Add this symbol to all ARM64 targets using kernel 4.14.

This mitigates CVE-2018-3639 on ARM64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 12:22:11 +03:00
Daniel Golle
7dcdf16222 kernel: remove duplicate #define's in at803x Ethernet PHY driver
AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined
upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg")
An existing local patch then added those exact same defines again which
isn't necessary, so remove them.

Fixes: f791fb4af4 ("kernel: add linux 4.9 support")
Fixes: b3f95490b9 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-07-31 05:28:48 +02:00
Daniel Golle
a497e47762 kernel: re-add patch for AT8032 Ethernet PHY
The patch was wrongly removed by a kernel version bump to 4.9.105 in
the believe that it was merged upstream thow it wasn't. This lead to
unrecoverable link losses on devices which use those PHYs such as
many ubnt single-port CPEs.

Fixes: 7dca1bae82 (kernel: bump to 4.9.105)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-07-31 04:56:58 +02:00
Stijn Tintel
ef025e6417 kernel: add pending e1000e fixes
The previous round of fixes for the 82574 chip cause an issue with
emulated e1000e devices in VMware ESXi 6.5. It also contains changes
that are not strictly necessary. These patches fix the issues introduced
in the previous series, revert the unnecessary changes to avoid
unforeseen fallout, and avoid a case where interrupts can be missed.

The final two patches of this series are already in the kernel, so no
need to include them here.

Patchwork: https://patchwork.ozlabs.org/cover/881776/

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 05:11:34 +03:00
Stijn Tintel
22b9f99b87 kernel: bump 4.14 to 4.14.59
Drop patch that was superseded upstream:
ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch

Drop upstreamed patches:
- apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch
- apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch
- ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch
- generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch
- generic/pending/900-gen_stats-fix-netlink-stats-padding.patch

In 4.14.55, a patch was introduced that breaks ext4 images in some
cases. The newly introduced patch
backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
addresses this breakage.

Fixes the following CVEs:
- CVE-2018-10876
- CVE-2018-10877
- CVE-2018-10879
- CVE-2018-10880
- CVE-2018-10881
- CVE-2018-10882
- CVE-2018-10883

Compile-tested: ath79, octeon, x86/64
Runtime-tested: ath79, octeon, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-07-31 05:11:07 +03:00
Matt Merhar
a2eaaaaf4b kernel: switch compatible property for RedBoot DT binding
This changes the DT binding's compatible property to
"ecoscentric,redboot-fis-partitions", removing the existing reference to
Red Hat.

Per the documentation hosted at eCosCentric's website, eCosCentric is
RedBoot's sole commercial maintainer since 2002, and the project has
been under the stewardship of the Free Software Foundation since 2008.

This also updates the property in the Inventel Livebox 1 .dts, the
binding's only current user.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-07-30 23:49:49 +02:00
John Crispin
5f5d812881 brcm2708: fix w1 patch
this is now part of generic

Signed-off-by: John Crispin <john@phrozen.org>
2018-07-30 20:51:56 +02:00
Sven Eckelmann
e3b8ae2b09 ipq40xx: Limit usable channels for OpenMesh A62 PHYs
The OpenMesh A62 is a tri-band device (1x 2.4GHz, 2x 5GHz) with special
filters in front of the RX+TX paths to the 5GHz PHYs. These filtered
channel can in theory still be used by the hardware but the signal strength
is reduced so much that it makes no sense.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-07-30 20:46:13 +02:00
Matt Merhar
af3b1756f0 ath79: fix irq assignment for pci-ar71xx driver
In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being
called before populating the PCI controller's device_node struct member.
This led to no IRQ being assigned to connected PCI devices (e.g. ath9k
cards) and caused them to be non-functional aside from simply being
detected.

The previous errors encountered in dmesg were: "irq: no irq domain found
for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ
of 0 for the cards.

While this has been only been tested on a yet-to-be-merged RouterStation
Pro target, it should also fix the broken wifi people have reported for
the ath79 WNDR3800 target.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2018-07-30 20:22:44 +02:00
Thibaut VARÈNE
c6ee683d64 ar71xx: define switch for rb-952ui-5ac2nd
QCA9533 built-in switch can be configured

Tested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2018-07-30 18:14:30 +02:00
Mantas Pucka
3dd692cd6b ipq40xx: fix booting secondary CPU cores
95672e04 broke booting secondary cores by removing 'qcom,saw' property
from L2 cache node. kpssv2_release_secondary() requires it.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2018-07-30 17:55:04 +02:00
John Crispin
eddf4eae97 ar71xx: fix TL-WR1043N v5 port mapping
fixes 5660c8fb20 ("ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.")

Signed-off-by: John Crispin <john@phrozen.org>
2018-07-30 17:47:06 +02:00
Tim Thorpe
5660c8fb20 ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.
Reversed the numbering of the LAN ports in Luci so as to match the port numbers on the housing.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
2018-07-30 16:31:18 +02:00
Tim Thorpe
d834ad9ac3 ar71xx: TL-WR1043N v4/v5: add orange WAN LED support
Add missing definitions for the orange WAN LED on the
TL-WR1043N(D) v4 and v5.

Change the name of a MAC address offset constant to
make it consistent with the format of the
existing constants.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
2018-07-30 16:30:34 +02:00
Lucian Cristian
accb67e582 ath79: add support for tl-wr841n-v9
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2018-07-30 16:14:49 +02:00
INAGAKI Hiroshi
ce93445cd6 ramips: add support for ELECOM WRC-2533GST
ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Core, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 4T4R 2.4/5 GHz wifi
  - MediaTek MT7615
- 5x 10/100/1000 Mbps Ethernet
- 4x LEDs, 6 keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Connect the computer to the LAN port of WRC-2533GST
2. Connect power cable to WRC-2533GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-07-30 15:55:21 +02:00
Kjel Delaey
8492ad0cc1 x86: add support to set GRUB menu entry title
$ make menuconfig

        Target Images -> Title for the menu entry in GRUB

Signed-off-by: Kjel Delaey <kjel_delaey@hotmail.com>
2018-07-30 15:55:21 +02:00
Ademar Arvati Filho
27b2f0fc0f kirkwood: add support for Iomega Storcenter ix2-200
Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
 Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
 flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC

Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console

Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    setenv serverip 192.168.1.1
    setenv ipaddr 192.168.1.13
    tftpboot 0x00800000 factory.bin
    nand erase 0x100000 $(filesize)
    nand write 0x00800000 0x100000 $(filesize)
    run bootcmd
    ```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
    ```
    mkfs.ext2 -L ext2 /dev/sdh1
    mount -t ext2 /dev/sdh1 /mnt
    cp initramfs-uImage /mnt/initramfs.bin
    umount /mnt
    ```
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
    ```
3. log into openwrt and sysupgrade to install into flash
    ```
    sysupgrade -n /tmp/sysupgrade.bin
    ```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-30 15:21:00 +02:00
Jianhui Zhao
84c212da44 samsung/s5pv210: New target
Signed-off-by: Jianhui Zhao <jianhuizhao329@gmail.com>
2018-07-30 14:10:00 +02:00
Keith Maika
4caab80830 ar71xx: add support for TP-Link Archer C59 v2
TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
2018-07-30 14:04:45 +02:00
Rafał Miłecki
a3d2448fae kernel: add missing include to redboot.c
This fixes:
drivers/mtd/redboot.c:299:34: error: array type has incomplete element type 'struct of_device_id'

Fixes: 5e8b4be531 ("kernel: add DT binding support to the mtd redboot parser")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-07-30 12:07:06 +02:00