This is required during early boot in the extroot setup phase to support
loading kmods from the overlay that depend on kmods on the rom partition.
The subsequent mount_root updates will use the LD_LIBRARY_PATH env
variable to pass kmod directories to kmodloader.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44533
This driver is used on IPQ806x to instanciate & drive the ethernet
interfaces.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44521
This adds the GMAC entries in the ipq806x dtsi file as well as in the
ap148 specific dts file.
This also adds the MDIO change as well.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44520
This change is fixing the issues observed when booting from NOR flash
with SMP enabled.
Error logs below:
building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of
xref (0 dead, 0 orphan) found.
m25p80 spi32766.0: SPI transfer failed: -110
spi_master spi32766: failed to transfer one message from queue
jffs2: Write of 873 bytes at 0x019001e8 failed. returned 0, retlen 792
Patch is cherry-picked from here:
https://www.codeaurora.org/cgit/quic/qsdk/oss/kernel/linux-msm/commit/drivers/spi/spi-qup.c?h=coconut_20140924&id=4faba89e3ffbb1c5f6232651375b9b3212b50f02
More details in the patch file.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44518
It took very little to make the TL-WDR4900 work under 3.19:
- config is the same as for 3.18
- only patch 210 had to be refreshed, the other patches are
the same as for 3.18
- in /etc/config/wireless the path options need to be prefixed
with "platform/" ('platform/ffe09000.pci/...')
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44517
This sets 'enable_vlan' and thus uses 802.1q
VLANs, but without tagging on either interface.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44509
Toggles the LA bit on the WAN interface.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44508
In a dual-WAN setup, it's useful to specify an interface over which to
have PPTP.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44507
When passing struct termios to ioctl TCGETS and TCSETS should be
used instead of TCGETA and TCSETA, which are meant for the older
struct termio. Should fix https://dev.openwrt.org/ticket/19012
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44506
ipq806x target has been upgraded to 3.14. There is no need to maintain
this file anymore.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44505
The watchdog driver already registers a restart notifier, we just have
to enable it in the config and in the DT to fix the "reboot" command.
This is done by integratin the following patch-set:
https://lkml.org/lkml/2015/2/20/610
I'm copy-pasting the description below:
qcom-wdt is currently assuming the presence of a dedicated node in DT
to gets its configuration. However, on msm architecture, the watchdog is
usually part of the timer block. So this patch-set is changing the driver
and slightly enhancing the timer DT bindings to provide the relevant clocks
and interrupts.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44504
Some bootloaders seem to trigger the watchdog during the boot process,
therefore the lack of watchdog driver trigger a reboot a few seconds
after boot. So we'll enable it here to avoid it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44503
MPIC timers are enabled in the config, however a devicetree clock setting
is missing causing the following error:
/soc@ffe00000/timer@41100: cannot get timer frequency.
/soc@ffe00000/timer@42100: cannot get timer frequency.
This patch adds the missing clock and avoids the error.
It's a functional copy of this code
do_fixup_by_compat_u32(blob, "fsl,mpic",
"clock-frequency", get_bus_freq(0), 1);
in arch/powerpc/cpu/mpc85xx/fdt.c in the u-boot code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44501
The firware md5sum check never worked due to missing dollar signs.
Also suppress
`md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44486
