Commit graph

2262 commits

Author SHA1 Message Date
Pawel Dembicki
20b09a2125 ramips: add support for Lava LR-25G001
The Lava LR-25G001 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN)
- 2x external, detachable antennas
- 1x USB 2.0
- UART (J3) header on PCB (57600 8n1)
- 8x LED (3x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- Work only three Gigabit ports (3/5, 1 WAN and 2LAN)

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Pawel Dembicki
b85fe43ec8 ramips: mt7620: add force use of mdio-mode
Some boards have external switches different than mt7530.

This patch allow to use mdio-mode without 0x1f register.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Weijie Gao
ed25e3ac02 ramips: fix some clocks in mt7621.dtsi
As the cpu clock calculation has been fixed, the clock for gic and spi
should be also fixed.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao
c7ca224299 ramips: fix cpu clock of mt7621 and add dt clk devices
For a long time the mt7621 uses a fixed cpu clock which causes a problem
if the cpu frequency is not 880MHz.

This patch fixes the cpu clock calculation and adds the cpu/bus clkdev
which will be used in dts.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao
f5af8be636 ramips: fix register range of memc node in mt7621.dtsi
The memc node from mt7621.dtsi has incorrect register resource.
Fix it according to the programming guide.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao
e217d69a4a ramips: merge two patches 101-mt7621-timer and 998-mt7621-needs-jiffies
These two patches both modified the mt7621.c, and the patch file
998-mt7621-needs-jiffies.patch adds only one line which is used by the
another patch file. So merge them into one file.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Lorenzo Bianconi
e612e60517 ramips: add mt76x0 node to RT-AC51U device tree
Introduce mt76x0e device tree node in RT-AC51U dts.
Define mt76x0e mtd partition and offset

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
2018-11-26 12:05:47 +01:00
Daniel Santos
89eb1a6d72 ralink: Add support for GPIO as interrupt-controller
The gpio-ralink driver has everything it needs to be used as an
interrupt controller except for device tree support.  This simple patch
adds that support by configuring the irq domain to use two cells and
adding the appropriate documentation to the devicetree bindings.

Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
2018-11-26 12:05:45 +01:00
Petr Štetiar
16b950c981 ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SK
On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory
OpenWrt image it's referenced as BDCOM WAP2100-SK device.

Specifications:

- SoC: MediaTek MT7620A
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 5 FE ports
- Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported)
- UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config
- LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G
- Other: USB port, SD card slot and 2x external antennas (non-detachable)

Flashing instructions:

A) The U-Boot has HTTP based firmware upgrade

  A1) Flashing notes

  We've identified so far two different batches of units, unfortunately
  each batch has different U-Boot bootloader flashed with different
  default environment variables, thus each batch has different IP address
  for accessing web based firmware updater.

  * First batch has web based bootloader IP address 1.1.1.1
  * Second batch has web based bootloader IP address 192.168.1.250

  In case you can't connect to either of those IPs, you can try to get
  the default IP address via two methods:

  A1.1) Serial console, then the IP address is visible during the boot

   ...
   HTTP server is starting at IP: 1.1.1.1
   raspi_read: from:40004 len:6
   HTTP server is ready!
   ...

  A1.2) Over telnet/SSH using this command:

   root@bdcom:/# grep ipaddr= /dev/mtd0
   ipaddr=1.1.1.1

  A2) Flashing with browser

  * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask
  * Reboot the device and try to reach web based bootloader in the
    browser with the following URL http://1.1.1.1

  * Quickly select the firmware sysupgrade file and click on the
    `Update firmware` button, this all has to be done within 10 seconds,
    bootloader doesn't wait any longer

   If done correctly, the web page should show UPDATE IN PROGRESS page
   with progress indicator. Once the flashing completes (it takes roughly
   around 1 minute), the device will reboot to the OpenWrt firmware

  A3) Flashing with curl

   sudo ip addr add 1.1.1.2/24 dev eth0
   curl \
      --verbose \
      --retry 3 \
      --retry-delay 1 \
      --retry-max-time 30 \
      --connect-timeout 30 \
      --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \
      http://1.1.1.1

   Now power on the router.

B) The U-boot is based on Ralink SDK so we can flash the firmware using UART.

   1. Configure PC with a static IP address and setup an TFTP server.
   2. Put the firmware into the tftp directory.
   3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX)
   4. Power up the device and press 2, follow the instruction to set device and
      tftp server IP address and input the firmware file name. U-boot will then load
      the firmware and write it into the flash.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:44 +01:00
Roman Yeryomin
ae2b43b873 ramips: fix ethernet for f5d8235-v2 board
Belkin F5D8235 v2 has two ethernet switches on board.
One internal rt3052 and rtl8366rb on rgmii interface.
Looks like internal switch settings were lost in
translation to device tree infrastructure.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:58:17 +01:00
Russell Senior
e42327aa89 ramips: add support for Skylab SKW92A in EVB
Specifically, SKW92A_E16, described here:

  http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
  to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board

Flash instruction:

>From Skylab firmware:

1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
   sysupgrade image, apply, flash will fail with a message:
   Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
   Unlocking mtd4 ...
   Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.

>From U-boot via TFTP and initramfs:

1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
   with sysupgrade.

>From U-boot via TFTP direct flash:

1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
   port 0 (WAN).

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-26 09:47:27 +01:00
Daniel Golle
7c4251d881 ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3
Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio
which wasn't supported at the time the devices were added to OpenWrt.
Now that we got it, include kmod-mt76x0e in images for those devices.

Reported-by: Arian Sanusi <openwrt@semioptimal.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-25 15:24:49 +01:00
Rafał Miłecki
9a3c805584 ramips: use separated mtd patch reverting write_page() removal
This helps understanding mtd changes needed to get downstream NAND
driver working.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-09 13:31:47 +01:00
Koen Vandeputte
b4e17a7440 ramips: fix netgear r6120 factory image generation
as indicated in commit c5bf408ed6 "(ramips: fix image generation for mt76x8")
more rework was needed to fix the other issues.

Building on another machine, but using the same arch, showed
the application failing again for different reasons.

Fix this by completely rewriting the application, fixing following found issues:

- buffer overflows, resulting in stack corruption
- flaws in memory requirement calculations (too small, too large)
- memory leaks
- missing bounds checking on string handling
- non-reproducable images, by using unitilized memory in checksum calculation
- missing error handling, resulting in succes on specific image errors
- endianness errors when building on BE machines
- various minor build warnings
- documentation did not match the code actions (header item locations)
- allowing input to be decimal, hex or octal now

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-08 13:32:22 +01:00
Felix Fietkau
b318edb999 ramips: add missing DTS frequency limit for the 5 GHz radio on Archer C20i
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-11-06 22:25:49 +01:00
Koen Vandeputte
c764b2b531 kernel: bump 4.14 to 4.14.79
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-05 16:00:00 +01:00
Martin Weinelt
0411813c6f
ramips: fix leds on GL.iNet GL-MT300N-V2
The WAN LED now shows the link state. It's color is green,
not blue.

Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
2018-11-02 21:43:15 +01:00
Baptiste Jonglez
b2c68ceea7 kernel: Add support for Winbond w25q128jv SPI NOR flash
Newer batches of several Mikrotik boards contain this yet-unsupported
flash chip, for instance:

- rb941-2nd (hAP lite)
- rb952ui-5ac2nd (hAP ac lite)
- RBM33G

and probably other Mikrotik boards need this patch as well.

The patch was submitted upstream by Robert Marko: https://patchwork.ozlabs.org/patch/934181/

Closes: FS#1715
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Robert Marko <robimarko@gmail.com>
2018-10-20 16:13:39 +02:00
Mathias Kresin
80c61c161a treewide: use wpad-basic for not small flash targets
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-16 15:07:41 +01:00
Felix Fietkau
d251a11f60 ramips: refresh mt7621 kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-15 12:54:12 +02:00
Koen Vandeputte
f983956a8b kernel: bump 4.14 to 4.14.75
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-10 14:45:11 +02:00
Mathias Kresin
b07b3ddaad ramips: don't hijack the status led
Don't hijack the status led to indicate the wireless state. If we don't
have a dedicated wireless led, it's as simply as the wireless status
can't be indicated.

Such a led misuse should be set by the user and not shipped by default.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:35:03 +02:00
Mathias Kresin
c074239c79 ramips: move status led unset to devicetree
Release the led used for boot status indication via devicetree instead
of setting a default off trigger in userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin
8f4dfadd5a ramips: add support for indicating the boot state using multiple leds
Use diag.sh version used for other targets supporting different leds
for the different boot states.

The existing led sequences should be the same as before.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin
772b27c207 ramips: set F5D8235 v1 usb led trigger via devicetree
Assign the usbdev trigger via devicetree and drop the userspace
handling of the usb leds.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin
04eab0a1c9 ramips: set rt2880 pci controller of_node
Set the PCI controller of_node such that PCI devices can be
instantiated via device tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Mathias Kresin
a58535771f ramips: set usb led trigger via devicetree
Assign the usbdev trigger via devicetree for all subtargets and drop
the userspace handling of the usb leds.

With the change all usb ports are triggering the usb led instead of
only usb 1.1 XOR usb 2.0 XOR usb 3.0 as it was before.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-07 11:34:18 +02:00
Koen Vandeputte
a2adeffffc kernel: bump 4.14 to 4.14.74
Refreshed all patches.

Fixes CVE:

- CVE-2018-7755

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-04 16:15:03 +02:00
Steffen Förster
8480907e70 ramips: fix Archer C20 sysupgrade
The sysupgrade image failed the check due to the wrong string in the
supported devices. This patch provides the correct name by dropping the
SUPPORTED_DEVICES to use the default generated name.

Signed-off-by: Steffen Förster <steffen@chemnitz.freifunk.net>
[drop the SUPPORTED_DEVICES, the old name was never used in a release]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-26 20:35:07 +02:00
Emil Muratov
8e6bc1a5be ramips: fix power LED DTB for wt3020
Since c134210 power LED is no longer lights after boot-up.
Reversing gpio polarity makes it work as it should be.

Signed-off-by: Emil Muratov <gpm@hotplug.ru>
2018-09-26 20:35:07 +02:00
Joseph C. Lehner
d6e39e7466 ramips: ex2700: actually remove kmod-mt76*
When building using the multiple devices option with per-device root
filesystem, only the meta package mt76 is omitted but not the
dependencies selected by the package.

Explicitly exclude all 3 mt76 packages, plus the metapackage.
Otherwise, these modules will be included in the build, wasting
a few hundred kilobytes.

Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[mention the root cause of the issue in the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-26 20:35:07 +02:00
Koen Vandeputte
0cda4af005 kernel: bump 4.14 to 4.14.70
Refreshed all patches.

Added new patch:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch

This fixes a bug introduced in upstream 4.14.68 which caused targets using
ubifs to produce file-system errors on boot, rendering them useless.

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-09-17 15:47:44 +02:00
Tobias Wolf
93bfafb8dc ramips: Fix early memory calculation for certain MIPS platforms
Kernel upstream commit 67a3ba25aa95 ("MIPS: Fix incorrect mem=X@Y handling") introduced a new issue for rt288x where "PHYS_OFFSET" is 0x0 but the calculated "ramstart" is not. As the prerequisite of custom memory map has been removed, this results in the full memory range of 0x0 - 0x8000000 to be marked as reserved
for this platform.

This patch adds the originally intended prerequisite again.

Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de>
2018-09-10 10:07:42 +02:00
Carlo Nel
6bbb220255 ramips: add support for TP-Link TL-MR3020 v3
TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N.

This PR is based on the work of @meyergru[1], with his permission.

Specification:
- MediaTek MT7628N/N (575 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet

Flash instruction:

The only way to flash the image in TL-MR3020 v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

[1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3

Signed-off-by: Carlo Nel <carlojnel@gmail.com>
2018-09-06 21:36:42 +02:00
Mathias Kresin
287b7aa583 ramips: drop obsolete sd card driver code
The pinmux for all SoCs using this driver is now set via the pinmux. It
makes this code obsolete.

Some of the code targeting the mt76x8 SoCs is still required. The sd
card pins share the pads with the EPHY. These pads need to be switched
to digital mode if the pins are used for sd cards.

The eMMC 8-bit mode has to be enabled via pinmux instead of a kernel
option. The uart2 group need to be set to function "sdxc d5 d4", pwm1
to "sdxc d6" and pwm0 to "sdxc d7" to do so. It can't be done by as
part of a default pinmux, as it would break the normal operation of
uart2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
563a5b5f94 ramips: add mt7620/1 sdhci pinmux
Set the pins to the required mode via the pinmux driver. It allows to
get rid of the pinmux related code in the sd card driver.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
a14097e8e0 ramips: fix mt7620a ND/SD pins pinmuxes
Drop the nd_sd gpio pinmux in case sdcard is used. They're mutually
exclusive and for most of the boards not even used as GPIOs.

If the pins are in sdcard mode, the pins ND_WE_N and ND_CS_N are still
GPIOs (#45 and #46).

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
2cc7980dcb ramips: reference node by label
Reference the HC5661A sdhci node by label instead of by the full path.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Mathias Kresin
1d08951628 ramips: add rt3352 SPI_CS1 pinmux
The rt3352 has a pin that can be used as second spi chip select,
watchdog reset or GPIO. The pinmux setup was missing the definition of
said pin but it is already used in the SoC dtsi.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-09-06 21:35:53 +02:00
Felix Fietkau
b605a84a74 ramips: ethernet: unify tx descriptor buffer splitting
A buffer is split into multiple descriptors if it exceeds 16 KB.
Apply the same split for the skb head as well (to deal with corner cases
on fraglist support)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-03 12:06:24 +02:00
Jo-Philipp Wich
4302c917cc Revert "ramips: mmc: Fix init for MT7628AN"
This reverts commit 3a8efaef00.

The change reportedly breaks UART2 on some boards. Furthermore it uses
bitwise logic on an uninitialized variable and fails to explain what it
is fixing exactly.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-30 13:19:26 +02:00
Jo-Philipp Wich
77e2bccde8 ramips: only limit lzma dictionary size on mt7621
The changed dictionary size leads to a different LZMA header which breaks
sysupgrade image magic checkibng on at least some RT288x boards.

Since the commit message only mentions testing on MT7621 and since the
change appears to break at least one other ramips subtarget, do not take
any chances and restrict the size limitation to only MT7621.

Fixes FS#1797
Fixes 09b6755946 ("ramips: limit dictionary size for lzma compression")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-08-30 10:57:35 +02:00
Mathias Kresin
a6e11ccb13 ramips: fix rt3883 pinmux for second SPI
The rt3883 doesn't have a pinmux group named spi_cs1. The cs1 is part
of the pci group. The function pci-func enables the second chip select.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 21:00:58 +02:00
Mathias Kresin
dcdc6d9dad ramips: fix rt3883 pci pinmux
The PCI pins need to be set to "PCI Host support one device" to allow
the use of one PCI device and flash memory.

The pci-fnc function is intended to be used if no PCI is used but
flash, nand or the codec functionality is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 21:00:58 +02:00
Mathias Kresin
c134210b8f ramips: drop pointless default led definitions
The LEDs should be triggered/lit by any kind of state change instead of
turned on/off unconditional.

If LEDs really need to be turned off by default, it should be done via
the default-state devicetree led property.

The handling of the wndr3700v5 and wt3020 power led is at least
strange. Something is for sure wrong with them. Either the leds are
misnamed, the default off trigger is a typo or the polarity of the
gpios is wrong. Drop the power led from userspace and wait for someone
with access to the hardware to fix it properly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:39:32 +02:00
Mathias Kresin
43df31f64d ramips: add missing zbt-cpe102 diag led
Based on the userspace led configuration it's quite obvious that the
4g-0 led should be used for boot status indication.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:34:09 +02:00
Mathias Kresin
99045dfc59 ramips: express diag led handling via devicetree
Use the default-state property to express the desired led handling in
the devicetree source file instead of the userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:34:07 +02:00
Mathias Kresin
111907e8d3 ramips: remove default on userspace trigger for diag leds
All the LEDs are turned on by diag.sh at the end of the boot process.
No need to do the same via userspace configuration again.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:26:24 +02:00
Mathias Kresin
56e6ebdea4 ramips: fix multi colour led handling
All boards either have a multi colour led or a single lightpipe. It
makes it impossible to handle the LEDs individual. Change the LED
config for these boards to take it into account.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:24:49 +02:00
Mathias Kresin
fe1e90deb4 ramips: rt-n12p: use the boardname helper variable
Use the helper variable for the Asus RT-N12P as it is done by all
boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-29 09:23:11 +02:00