OWE is defined in RFC 8110 and provides encryption and forward security
for open networks.
This is based on the requirements in the Wifi alliance document
Opportunistic_Wireless_Encryption_Specification_v1.0_0.pdf
The wifi alliance requires ieee80211w for the OWE mode.
This also makes it possible to configure the OWE transission mode which
allows it operate an open and an OWE BSSID in parallel and the client
should only show one network.
This increases the ipkg size by 5.800 Bytes.
Old: 402.541 Bytes
New: 408.341 Bytes
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This build the full openssl and wolfssl versions with SAE support which
is the main part of WPA3 PSK.
This needs elliptic curve cryptography which is only provided by these
two external cryptographic libraries and not by the internal
implementation.
The WPA3_Specification_v1.0.pdf file says that in SAE only mode
Protected Management Frames (PMF) is required, in mixed mode with
WPA2-PSK PMF should be required for clients using SAE, and optional for
clients using WPA2-PSK. The defaults are set now accordingly.
This increases the ipkg size by 8.515 Bytes.
Old: 394.026 Bytes
New: 402.541 Bytes
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This replaces the configuration files with the versions from the hostapd
project and the adaptions done by OpenWrt.
The resulting binaries should be the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Check pin count value from pin status and stop verification the pin if
the value is less then 3. This should prevent the proto-handler to
lock the SIM. If SIM is locked then the PUK is needed.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Load the json output from uqmi --get-pin-status command and evaluate the
"pin1_status" value.
The following uqmi "pin1_status" values are evaluated:
- disabled
Do not verify PIN because SIM verification is disabled on this SIM
- blocked
Stop qmi_setup because SIM is locked and a PUK is required
- not_verified
SIM is not yet verified. Do a uqmi --verify-pin1 command if a SIM is
specified
- verified:
Do not verify the PIN because this was already done before
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
QMI proto setup-handler will wait forever if SIM does not get initialized.
To fix this stop polling pin status and notify netifd. Netifd will generate
then a "ifup-failed" ACTION.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
QMI proto setup-handler will wait forever if it is unable to registrate to
the mobile network. To fix this stop polling network registration status
and notify netifd. Netifd will generate then a "ifup-failed" ACTION.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This value will be used for now during following situations:
* Ask the sim with the uqmi --get-pin-status command.
* Wait for network registration with the uqmi --get-serving-system command.
This two commands wait forever in a while loop. Add a timeout to stop
waiting and so inform netifd.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Move uqmi std and error output on commands without using them to /dev/null.
This will remove useless outputs in the syslog.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
dnsmasq v2.80test8 adds the ability to ignore dhcp client's requests for
specific hostnames. Clients claiming certain hostnames and thus
claiming DNS namespace represent a potential security risk. e.g. a
malicious host could claim 'wpad' for itself and redirect other web
client requests to it for nefarious purpose. See CERT VU#598349 for more
details.
Some Samsung TVs are claiming the hostname 'localhost', it is believed
not (yet) for nefarious purposes.
/usr/share/dnsmasq/dhcpbogushostname.conf contains a list of hostnames
in correct syntax to be excluded. e.g.
dhcp-name-match=set:dhcp_bogus_hostname,localhost
Inclusion of this file is controlled by uci option dhcpbogushostname
which is enabled by default.
To be absolutely clear, DHCP leases to these requesting hosts are still
permitted, but they do NOT get to claim ownership of the hostname
itself and hence put into DNS for other hosts to be confused/manipulate by.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
64750c1 version: bump snapshot
f11a2b8 global: style nits
4b34b6a crypto: clean up remaining .h->.c
06d9fc8 allowedips: document additional nobs
c32b5f9 makefile: do more generic wildcard so as to avoid rename issues
20f48d8 crypto: use BIT(i) & bitmap instead of (bitmap >> i) & 1
b6e09f6 crypto: disable broken implementations in selftests
fd50f77 compat: clang cannot handle __builtin_constant_p
bddaca7 compat: make asm/simd.h conditional on its existence
b4ba33e compat: account for ancient ARM assembler
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
e1791f3 Fix logging of DNSSEC queries in TCP mode. Destination server address was misleading.
0fdf3c1 Fix dhcp-match-name to match hostname, not complete FQDN.
ee1df06 Tweak strategy for confirming SLAAC addresses.
1e87eba Clarify manpage for --auth-sec-servers
0893347 Make interface spec optional in --auth-server.
7cbf497 Example config file fix for CERT Vulnerability VU#598349.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Support for -D got broken in the 2.0.11 release by the upstream commit
218d8c667944 ("first pass L2 mode w/UDP checks, v4 only"). After that
commit clients were still able to connect but no traffic was passed.
It was reported and is fixed now in the upstream git repository.
Backport two patches to fix this. The first one is just a requirement
for the later to apply. The second one is the real fix and it needed
only a small adjustment to apply without backporing the commit
10887b59c7e7 ("fix --txstart-time report messages").
Fixes: 457e6d5a27 ("iperf: bump to 2.0.12")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* Account for big-endian 2^26 conversion in Poly1305.
* Account for big-endian NEON in Curve25519.
* Fix macros in big-endian AArch64 code so that this will actually run there
at all.
* Prefer if (IS_ENABLED(...)) over ifdef mazes when possible.
* Call simd_relax() within any preempt-disabling glue code every once in a
while so as not to increase latency if folks pass in super long buffers.
* Prefer compiler-defined architecture macros in assembly code, which puts us
in closer alignment with upstream CRYPTOGAMS code, and is cleaner.
* Non-static symbols are prefixed with wg_ to avoid polluting the global
namespace.
* Return a bool from simd_relax() indicating whether or not we were
rescheduled.
* Reflect the proper simd conditions on arm.
* Do not reorder lines in Kbuild files for the simd asm-generic addition,
since we don't want to cause merge conflicts.
* WARN() if the selftests fail in Zinc, since if this is an initcall, it won't
block module loading, so we want to be loud.
* Document some interdependencies beside include statements.
* Add missing static statement to fpu init functions.
* Use union in chacha to access state words as a flat matrix, instead of
casting a struct to a u8 and hoping all goes well. Then, by passing around
that array as a struct for as long as possible, we can update counter[0]
instead of state[12] in the generic blocks, which makes it clearer what's
happening.
* Remove __aligned(32) for chacha20_ctx since we no longer use vmovdqa on x86,
and the other implementations do not require that kind of alignment either.
* Submit patch to ARM tree for adjusting RiscPC's cflags to be -march=armv3 so
that we can build code that uses umull.
* Allow CONFIG_ARM[64] to imply [!]CONFIG_64BIT, and use zinc arch config
variables consistently throughout.
* Document rationale for the 2^26->2^64/32 conversion in code comments.
* Convert all of remaining BUG_ON to WARN_ON.
* Replace `bxeq lr` with `reteq lr` in ARM assembler to be compatible with old
ISAs via the macro in <asm/assembler.h>.
* Do not allow WireGuard to be a built-in if IPv6 is a module.
* Writeback the base register and reorder multiplications in the NEON x25519
implementation.
* Try all combinations of different implementations in selftests, so that
potential bugs are more immediately unearthed.
* Self tests and SIMD glue code work with #include, which lets the compiler
optimize these. Previously these files were .h, because they were included,
but a simple grep of the kernel tree shows 259 other files that carry out
this same pattern. Only they prefer to instead name the files with a .c
instead of a .h, so we now follow the convention.
* Support many more platforms in QEMU, especially big endian ones.
* Kernels < 3.17 don't have read_cpuid_part, so fix building there.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
33523a5 version: bump snapshot
0759480 curve25519-hacl64: reduce stack usage under KASAN
b9ab0fc chacha20: add bounds checking to selftests
2e99d19 chacha20-mips32r2: reduce stack and branches in loop, refactor jumptable handling
d6ac367 qemu: bump musl
28d8b7e crypto: make constant naming scheme consistent
56c4ea9 hchacha20: keep in native endian in words
0c3c0bc chacha20-arm: remove unused preambles
3dcd246 chacha20-arm: updated scalar code from Andy
6b9d5ca poly1305-mips64: remove useless preprocessor error
3ff3990 crypto-arm: rework KERNEL_MODE_NEON handling again
dd2f91e crypto: flatten out makefile
67a3cfb curve25519-fiat32: work around m68k compiler stack frame bug
9aa2943 allowedips: work around kasan stack frame bug in selftest
317b318 chacha20-arm: use new scalar implementation
b715e3b crypto-arm: rework KERNEL_MODE_NEON handling
77b07d9 global: reduce stack frame size
ddc2bd6 chacha20: add chunked selftest and test sliding alignments and hchacha20
2eead02 chacha20-mips32r2: reduce jumptable entry size and stack usage
a0ac620 chacha20-mips32r2: use simpler calling convention
09247c0 chacha20-arm: go with Ard's version to optimize for Cortex-A7
a329e0a chacha20-mips32r2: remove reorder directives
3b22533 chacha20-mips32r2: fix typo to allow reorder again
d4ac6bb poly1305-mips32r2: remove all reorder directives
197a30c global: put SPDX identifier on its own line
305806d ratelimiter: disable selftest with KASAN
4e06236 crypto: do not waste space on selftest items
5e0fd08 netlink: reverse my christmas trees
a61ea8b crypto: explicitly dual license
b161aff poly1305: account for simd being toggled off midway
470a0c5 allowedips: change from BUG_ON to WARN_ON
aa9e090 chacha20: prefer crypto_xor_cpy to avoid memmove
1b0adf5 poly1305: no need to trick gcc 8.1
a849803 blake2s: simplify final function
073f3d1 poly1305: better module description
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Bump to latest test release:
3a610a0 Finesse allocation of memory for "struct crec" cache entries.
48b090c Fix b6f926fbefcd2471699599e44f32b8d25b87b471 to not SEGV on startup (rarely).
4139298 Change behavior when RD bit unset in queries.
51cc10f Add warning about 0.0.0.0 and :: addresses to man page.
ea6cc33 Handle memory allocation failure in make_non_terminals()
ad03967 Add debian/tmpfiles.conf
f4fd07d Debian bugfix.
e3c08a3 Debian packaging fix. (restorecon)
118011f Debian packaging fix. (tmpfiles.d)
Delete our own backports of ea6cc33 & 4139298, so the only real changes
here, since we don't care about the Debian stuff are 48b090c & 3a610a0
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
musl doesn't come with an valid implementation of `sched_getscheduler()`;
it simply returns -ENOSYS for it. Without this option (and compile dante
with `sched_getscheduler()` enabled), you will get
error: serverinit(): sched_getscheduler(2): failed to retrieve current
cpuscheduling policy: Function not implemented
and dante won't start at all.
Ref: http://lists.alpinelinux.org/alpine-devel/3932.html
Ref: http://lists.alpinelinux.org/alpine-devel/3936.html
Signed-off-by: David Yang <mmyangfl@gmail.com>
[slightly reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The restool failed to work with current gcc-7.3.0-musl.
This patch is to add a restool fix-up patch to fix
multiple problems encountered in the get_device_file()
function:
- The deprecated atoi() function is replaced by strtoul
- An invalid memory access was being performed by using
memory from dir->d_name even after closedir(). This is
fixed by a strdup() on the device filename.
- Also, error prints now print any relevant error code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The restool source code had been migrated to codeaurora
for LSDK-18.06 release and the future release. This patch
is to update restool to LSDK-18.06 release.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Backport upstream commit
Change anti cache-snooping behaviour with queries with the
recursion-desired bit unset. Instead to returning SERVFAIL, we
now always forward, and never answer from the cache. This
allows "dig +trace" command to work.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
/etc/config/lldpd is only used by the init script, which only runs as root
Adjusted homepage and download URLs to use HTTPS.
-std=c99 is useful for GCC versions less than 6. Current OpenWrt uses 7.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Setting encaplimit to a numerical value results into the value being
included as tunnel encapsulation limit in the destination option header
for tunneled packets.
Several users have reported interop issues as not all ISPs support the
destination option header containing the tunnel encapsulation limit
resulting into broken map connectivity.
Therefore drop the default encaplimit value for map tunnels so
no destination option header is included by default.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
