This enables misaligned access handling by software in Linux kernel.
With some wireless drivers (ath9k-htc and mt7601u for example) we see
misaligned accesses here and there and to cope with that without
fixing stuff in the drivers we're just gracefully handling it on ARC.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 49134
AXS101 beind a development board lacks built-in wireles inerfaces.
So we have to use external USB dongles to turn the board into
wireless router.
The best USB Wi-Fi dongles to work in AP-mode seem to be based on
ath9k-htc chipset.
And so with that change we add support of mentioned dongles in
default and axs101 builds.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 49133
Misc fixes for LinkIt 7688 board:
- Copy the right wireless firmware for the mt7688
- Add back '0065-mt7688-fixes.patch', left out after the move to Linux 4.4.
- Remove SPI_DEV from linux config which otherwise causes a massive warning
- Add wmac to LINKIT7688.dts so wireless works
Signed-off-by: Adam Kent <adam@semicircular.net>
SVN-Revision: 49130
Currently the maximum image size defaults to 8Mbyte even though this model has 16Mbyte of flash memory.
Tested and works on my device.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
SVN-Revision: 49129
Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware).
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49127
This reverts commit r48961. It didn't fix PCIe host driver issue as
there are more aborts triggered by it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49120
4.3 isn't oficially used anymore but it may be useful for debugging PCI
host driver regression. SPROM driver doesn't seem to work correctly with
4.3:
[ 2.336686] bcma: bus0: Using fallback SPROM failed (err -2)
[ 2.342366] bcma: bus0: No SPROM available
but it at least compiles now.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49113
Let's not confuse users about the revisions of their devices when we can
easily avoid it.
Not tested on real hardware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49107
Instead of adding the space when combining $model and $hwver, add the space
to the beginning of $hwver, so the resulting string won't end with a space
when $hwver is set to the empty string.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49106
There's no reason for us to be more lenient than the stock firmware, so
better check the HWREV as well to avoid bricked devices.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 49105
- all subtarget specific defines are in their own files
- common defines left in main Makefile
- each subtarget makefile idefed with SUBTARGET
- all subtargets compile tested
- few seems to be broken/unneeded things marked with FIXME
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 49104
This patch provides full GPIO support for WNR2200 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49101
Fix for invalid/random/duplicate WLAN MAC address in WNR2200.
Permanent platform MAC is calculated and assigned during system startup.
WLAN MAC follows wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49100
This patch adds support for the TP-Link TL-WR841N/ND to trunk. It is
similar to the already supported v10 - see [1]. I have added support
based on that topic; in the meantime it has been confirmed working
(see the forum thread, and also [2]).
Signed-off by Stijn Segers <francesco.borromini@inventati.org>
[1]: https://forum.openwrt.org/viewtopic.php?id=61309
[2]: https://forum.openwrt.org/viewtopic.php?id=63657
SVN-Revision: 49099
On most platforms the cmdline is supplied by the loader to the kernel.
When using an elf loader with cmdline the size is bloated by 512k.
For loader-elf platforms like the cpe510 better use loader-elf but patch
the cmdline into the kernel.
wdr1043: Tested loader still works using sysupgade image.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49080
The loader decompress a lzma compressed kernel. Some bootloaders
only support elf files like the tplink cpe510
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49079
This patch provides full GPIO support for WNR1000v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49076
Not all mach-* files set all boards correctly in ETH_CFG. They depend on
some preset values by u-boot which were not previously modified by
ath79_setup_qca955x_eth_cfg. Avoiding to modify them in this function keeps
it backward compatible for these boards.
This reverts commit 119b8ab2c2eac237ec4e9c4d0ed53df22b5c6978.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49072
The default delays RXD 3. RDV 3, TXD 0, TXE 0 doesn't seem to work for some
boards. These boards depend on the preset values of u-boot which may
differ.
This reverts commit f2d4bb96b62512caa161dcc2867c91692fb16a38.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49071
The MR1750 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR1750 can be used instead.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49070
The MR900 must unset some bits in ETH_CFG which were set by u-boot to work
correctly under OpenWrt. But the global function
ath79_setup_qca955x_eth_cfg will not unset all of them to increase the
backward compatiblity with older mach-* files. A private (simplified)
version for MR900 can be used instead.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49069
Work-around obsolete mkfs/ubifs code.
Unlike squashfs, ubifs images should be generated per-device so
minimum I/O unit size, logical erase block size, maximum logical erase
block count can be defined for the specific flash-chips parameters.
Also, generating ubinized images is unrelated to rootfs being ubifs or
squashfs, but rather depends on the device supporting UBI or not.
In the meantime and in order to fix an error which currently causes the
image generation on buildbot to fail, work-around by defining
UBIFS_OPTS for the Default profile.
See also
http://buildbot.openwrt.org:8010/builders/oxnas/builds/246/steps/compile_8/logs/stdio
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49068
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.
The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.
Fix the assembly code to reserve stack space for the
registers to avoid that.
Untested. It seems that the lzma-loader is not used at all?
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49062
According to the calling convention of the o32 ABI the
caller function must reserve stack space for $a0-$a3
registers in case the callee needs to save its arguments.
The assembly startup code does not reserve stack space
for these registers thus when the main C function needs
to save its arguments, that will cause a stack overflow.
Fix the assembly code to reserve stack space for the
registers to avoid that.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49061
The current code only partially invalidates both caches
because the cache size and cache-line size values are
incorrectly passed to the C code.
Fix the assembly code to pass the arguments in the correct
order.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49060
The current code only partially invalidates both caches
because the cache size and cache-line size values are
incorrectly passed to the C code.
Fix the assembly code to pass the arguments in the correct
order.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49058
The current code only partially invalidates both caches
because the cache size and cache-line size values are
incorrectly passed to the C code.
Fix the assembly code to pass the arguments in the correct
order.
Tested on RB532.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49056
Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3
and WNR612v2.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 49051
Instead of using our patch-dtb program just place the device tree
behind the kernel binary and then let the in kernel mechanism fetch it.
This also adds support for having the device tree file in the boot
loader.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 49050
1) Use leds to indicate:
Red - Power
Amber - Radio On
Blue - Wifi associated
2) Add profile to default build group for MT7628 subtarget
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
SVN-Revision: 49045
Make mach-oxnas/hotplug.c look more similar to mach-realview/hotplug.c,
just cosmetics and maintainability concerns, no functional changes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49044
Clear both, SYS_CTRL_*_SEL and SEC_CTRL_*_SEL on boot instead of
writing to SYS_CTRL_*_SEL twice which looks like a copy-paste error.
Thanks to anonymous to bring this up in #21892!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 49042
The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.
This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.
Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49031
The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.
This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.
Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49030
Some u-boot versions for QCA955x change the delays based on the link speed
during boot. This usually breaks the support of other linkspeeds when
OpenWrt is booted. It also conflicts with the
at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own
values in QCA955X_GMAC_REG_ETH_CFG.
The default RGMII values from the Atheros u-boot are currently used to
preset the existing mach files. These may have to be adjusted for boards
using different values but which are not currently set them explicitely in
OpenWrt.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Christian Beier <cb@shoutrlabs.com>
Cc: Chris R Blake <chrisrblake93@gmail.com>
Cc: Benjamin Berg <benjamin@sipsolutions.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Cc: Dirk Neukirchen <dirkneukirchen@web.de>
Cc: Christian Mehlis <christian@m3hlis.de>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 49029
Some u-boot versions for QCA955x set currently not cleared bits depending
on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c
file is responsible to select the correct configuration bits and thus the
ath79_setup_qca955x_eth_cfg has to clear the unset.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49028
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
Dropped patches because they applied upstream:
- 120-iomega_ix2_200.patch
- 150-pogoplug_e02.patch
Tested on dockstar and goflexnet.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 49019
Previous the uboot was overwriting the device-tree's mtd layout to use
the last 3 mb.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49015
The kernel will automatic attach mtd partitions named 'ubi' to ubi0.
Renaming the "root" partition into "ubi" will safe arguments
from the kernel cmdline.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49014
the kernel tries to use "ubi" or "data" labeled partition to find it's root filesystem.
dockstar don't need anymore mtdparts= nor root= bootarguments
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49011
The new image requires `bootz` because of devicetree appending.
To flash a new image boot initramfs:
tftpboot 0x800000 openwrt-kirkwood-dockstar-initramfs-kernel.bin
bootz 0x800000
# detach if already attached
ubidetach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')
# scp openwrt-kirkwood-dockstar-squashfs-factory.bin /tmp
ubiformat -f /tmp/openwrt-kirkwood-dockstar-squashfs-factory.bin
# attach is important to resize rootfs_data otherwise it wont boot
ubiattach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49010
Apart from using our new building system there are 2 more changes:
1) Limit amount of images
So far we were generating all standard images (optimized one and two
with no loader) for every SUBTARGET. This is not needed, as e.g. the
only device requiring gzipped kernel is legacy Huawei E970.
2) Change output names
The new image building system requires specifying device name. This
forced picking some and resulted in:
openwrt-brcm47xx-$(SUBTARGET)-squashfs.trx
openwrt-brcm47xx-$(SUBTARGET)-squashfs-gz.trx
openwrt-brcm47xx-$(SUBTARGET)-squashfs-noloader-nodictionary.trx
becoming:
openwrt-brcm47xx-$(SUBTARGET)-standard-squashfs.trx
openwrt-brcm47xx-$(SUBTARGET)-standard-noloader-gz-squashfs.trx
openwrt-brcm47xx-$(SUBTARGET)-standard-noloader-nodictionarylzma-squashfs.trx
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 49006
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.
SVN-Revision: 48994
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.
SVN-Revision: 48993
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.
SVN-Revision: 48992
A re-write of the driver based on xway_nand.c and constants as
well as the cmd_ctrl() function from the original oxnas_nand.c
resulted in a extremely similar looking file (see diffsize),
and fixes the issue of NAND not being detected on newer kernels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 48986
As usual these patches were extracted from the raspberry repo:
https://github.com/raspberrypi/linux/commits/rpi-4.4.y
- Disable unused MFD RPISENSE driver.
- Disable ethernet HW checksums in order to avoid kernel exceptions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48985
Looks like the addresses for BCM3368 were wrongly defined when DT
support was introduced.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48980
According to the calling convention of the o32 ABI the caller
function must reserve stack space for $a0-$a3 registers in case
the callee needs to save its arguments.
The assembly code of the loader does not reserve stack space for
these registers thus when the 'loader_main' function needs to save
its arguments, those will be stored in the 'workspace' area instead
of the stack.
Because the workspace area is also used by other part of the code, the
saved register values gets overwritten and this often leads to failed
kernel boots.
Fix the code to reserve stack space for the registers to avoid this
error.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
[noltari: apply the fix for brcm63xx too]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48979
This only drops WGR614 V9 which has 2 MiB flash and it's unlikely to get
any interest.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48975
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 48968
Complete internal switch initialization for QCA956X.
Set default mdio device if the interface mode of GE0 is not SGMII (fix ticket #21520).
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 48937
The function memblock_insert_region() is in the section
__init_memblock, also put crashlog_init_memblock there.
This fixes this section mismatch warning:
The function memblock_insert_region.isra.1() references
the function __meminit crashlog_init_memblock().
This is often because memblock_insert_region.isra.1 lacks a __meminit
annotation or the annotation of crashlog_init_memblock is wrong.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48931
The buildbots complained about these config options being missing for arm64:
CONFIG_DUMMY_CONSOLE_COLUMNS=80
CONFIG_DUMMY_CONSOLE_ROWS=25
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48929
This patch provides full GPIO support for WNR612v2 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48924
This patch add speed_mask parameter to Ethernet port LED initialization
during system startup. LEDs are configured to show amber light for 10 Mbps
link and green for 100 Mbps as described on device label.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48923
This patch provides full GPIO support for WNR2000v3 (LEDs and buttons).
It exposes all LEDs to operating system, including Ethernet ones.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48922
Combine all bus operations for one MMD access in one function.
Protecting all these bus operations with one lock also helps
to avoid potential issues due to bus operations intercepting
the register and data write.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48914
The default TTL for address resolution table entries is 5 minutes
for all members of the AR8216 family. This can cause issues if
e.g. Wifi clients roam to another AP and their MAC appears on
another switch port suddenly. Then the client may not be reachable
until the old ARL entry expires.
I would have expected the switch to invalidate old entries if it
detects the same MAC on another port. But that's not the case.
Therefore make the TTL for ARL entries configurable.
The effective TTL will always be a multiple of 7 seconds.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48913
The line before includes the port number anyway so there's no need
to duplicate the port number in the MIB info header.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48912
The decimal values especially for TxByte and RxGoodByte are hard to read
once bigger amounts of data have been transferred.
Therefore complement the decimal values with info in GiB / MiB / KiB.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48911
For unused switch ports all MIB values are zero. Displaying ~40 empty
MIB counters is just confusing and makes it hard to read the output of
swconfig dev <dev> show.
Therefore, if all MIB counters for a port are zero, just display
an info that the MIB counters are empty.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48910
This patch adds profiles and support for building factory and
sysupgrade images for JHR-N805R, JHR-N825R and JHR-N926R.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48906
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48905
Add a device tree for JCG JHR-N825R
This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. As a special feature, it comes with a two digit seven segment
display that is connected to a pair of daisy-chained 74164 shift
registers that can be controlled via GPIOs.
For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48904
Add a device tree for JCG JHR-N825R
This router is based on a RT3052 and has 4MB of CFI flash and 32MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N825R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48903
Add a device tree for JCG JHR-N805R
This router is based on a RT3050 and has 4MB of SPI flash and 16MB of
SDRAM. For details, see https://wikidevi.com/wiki/JCG_JHR-N805R .
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48902
Commit d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026")
incorrectly changed the mode of the ramips shell scripts from 755 to 644.
I.e., they are not excutable any more and for example devices will be left
with broken configs.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 48893
Enable platform-supplied WLAN LED name for ath9k device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48879
This patch moves the OOLITE profile code into the overarching Gainstrong
profile and deletes the old single profile file.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 48866
The ubdev01 profile defines its own MTDPARTS with smaller firmware
partition, so give it its own UBNT_BOARD in mkfwimage.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48828
This is the first patch of a series of three to tidy up the profiles for
Gainstrong devices. Right now there are two Gainstrong profiles, each
for a single device built by this manufacturer. This patch renames the
MiniBox profile to Gainstrong and updates the copyright notice.
The series applies cleanly to current trunk. Resent with the architecture in
the subject, forgot that the first time.
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 48797
Hi,
the board in subject (RT5350F-OLinuXino-EVB) still ships from vendor
with a RC3 image built upon a .dts file which declares GPIO12 and GPIO14
as relay2 and relay1 respectively, as you can see from their rt5350f
branch on GitHub.
For some reason in the official stable build both the GPIOs are swapped
and the wrong names are declared in the gpio-export directive.
I'm submitting this patch which should roll back the wrong changes, so
that we get backward compatibility with any script developed on RC3
which controls the relays.
After patching correct operation is restored:
root@OpenWrt:/# cat /sys/kernel/debug/gpio
GPIOs 0-21, platform/10000600.gpio, 10000600.gpio:
gpio-0 (button ) in hi
gpio-12 (relay2 ) out lo
gpio-14 (relay1 ) out lo
Thank you,
Signed-off-by: Lorenzo Cafaro <lorenzo@ibisco.net>
SVN-Revision: 48796
The vdso version of this function has some problems with the cache.
Very often it works on dated data which causes problem. We are
currently working on fixing this in upstream Linux kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48787
Fix for invalid/random WLAN MAC address in WNR612v2. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses. This is the same fix as for WNR2000v3.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48779
Netgear WNR612v2 has no USB port yet default system image
includes USB kernel modules. This patch fixes that.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48778
Fix for invalid/random WLAN MAC address in WNR2000v3. Permanent platform
MAC is calculated and assigned during system startup. WLAN MAC follows
wired Ethernet interface addresses.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48777
This patch adds speed_mask special file to LEDs connected to switch ports
via 'switch' trigger. It allows to choose which speeds to signal when link
is up. If router has more than one LED per port, they may light up
differently depending on how fast connection is. Default setting is 'all
speeds' so backward compatibility with system scripts (for example uci) is
maintained.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48775
This patch changes swconfig_trig_port_mask_store() handler to utilize
kstrtoul() function instead of call to obsolete simple_strtoul(). Thanks
to this change, new handler takes less memory and makes port_mask special
file accept not only hexadecimal, but also decimal and octal numbers.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48774
As indicated in the bug tracker[1], failsafe mode is broken on at least some
devices using the mt7620 switch (and possibly mt7621). The thread explicitly
mentions the Xiaomi MiWifi, and the Nexx WT3020, and an unspecified device
using the mt7621 switch; the issue also applies to the Netgear EX2700.
The problem is that failsafe mode uses eth0, but enable_vlan is always set to 1
by the switch driver. Connecting to and/or pinging the device fails. This patch
fixes the failsafe preinit config, by making sure that vlan support is disabled.
It currently only fixes the switch config on mt7620, but might apply to the
mt7621 as well, so the patch has been designed with this in mind.
A similar (line wrapped) patch was submitted in December by Simon Peter, but never
accepted and/or discussed.
This patch applies to both Chaos Calmer and trunk.
[1] https://dev.openwrt.org/ticket/18768
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48772
This patch adds support for building factory and sysupgrade images
for the Netgear EX2700 that don't require modification of u-boot
environment variables.
The bootloader on this device expects the kernel partition to end
on a 64k block boundary. The last 64 byte of the kernel partition
must contain a valid uImage header - in the stock firmware, this is
the uImage header of the root filesystem. For this patch, we're using
the uImage header of a 0 byte partition (ex2700-fakeroot.uImage).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48771
- remove the suffix (N, ND) to indicate that the image is for all
WR841-models
- some of these models have a "N"-suffix, others have (ND)-suffix,
but the boards are the same - only difference is the detachable
antenna on "D"-models
- discussed this idea to remove the suffix in IRC with jow and Borromini
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
SVN-Revision: 48767
Seama format has 2 similar headers: container (seal) header and entity
header. The first one has size always set to 0 and doesn't contain MD5
digest.
When dealing with Seama on a flash we deal directly with an entity. You
can see mtdsplit_parse_seama reads from offset 0 and expects entity to
be there. Seama container is used by bootloader / interface only which
extract entity out of it and flash it.
That said we should fix our header struct. This is important as we
calculate possible rootfs offset assuming it may be placed right after
Seama entity. So far calculate offset was always 16B too low.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48754
- Fix typo in board_data partition start address
- Increase board_data partition size in order to exploit all flash size
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
SVN-Revision: 48751
This patch introduces support of new boards with ARC HS38 cores.
ARC HS38 is a new generation of ARC cores which utilize ARCv2 ISA.
As with ARC770 we're addind support for 2 boards for now:
[1] Synopsys SDP board (AXS103)
This is the same base-board as in AXS101 but with
FPGA-based CPU-tile where ARCHs38 core is implemented.
[2] nSIM
Again this is the same simulation engine but configured for
new instruction set and features of new CPU.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48740
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
SVN-Revision: 48721
Netgear WNR2000v3 has no USB port yet default system image
includes USB kernel modules. This patch fixes that.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48701
Avoids inadvertent file creation when executing
`/etc/init.d/dsl_control status`.
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
SVN-Revision: 48700
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.
What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48698
Add support for Xilinx ZC702 Dev board
Zynq target is using 4.4 kernel and mainline 2016.1 u-boot.
Patch is tested with Xilinx ZC702 Dev board with SD boot mode.
known issues:
- no QSPI driver in 4.4 kernel: no QSPI flash support
- USB is not working in 4.4 kernel
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
create mode 100644 package/boot/uboot-zynq/Makefile
create mode 100644 target/linux/zynq/Makefile
create mode 100644 target/linux/zynq/base-files.mk
create mode 100755 target/linux/zynq/base-files/etc/board.d/02_network
create mode 100644 target/linux/zynq/base-files/etc/config/network
create mode 100644 target/linux/zynq/base-files/etc/inittab
create mode 100644 target/linux/zynq/config-4.4
create mode 100644 target/linux/zynq/image/Makefile
create mode 100755 target/linux/zynq/image/mkits.sh
create mode 100644 target/linux/zynq/patches-4.4/0001-arm-dts-zynq-zc702.dts-Set-default-rdinit-to-sbin-in.patch
create mode 100644 target/linux/zynq/profiles/zc702.mk
SVN-Revision: 48697
Update OpenWRT build tree to reflect changes in TLC-591xx LED family driver.
In kernels < 4.0 the driver was present in form of a patch for the TLC-59116 chip,
and was upstreamed later in kernels > 4.0 to support the entire chip family.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
[jow: fix Kconfig symbol name]
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 48684
With this patch sysupgrade will write directly to the partitions
instead of to the main disk. The UUID is copied from the image
to the MBR as well. This prevents the mbr from being completely
overwritten and losing the partition table. The -p option has
been added to maintain the original behavior and overwite the
entire disk with the new image. Tests have been added to ensure
that the image partitions match up with the active partitions.
Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net>
SVN-Revision: 48682
The top half of UARTF on the HLK-RM04 is used for GPIO.
mode 1 mode 2
RIN GPIO14
DSR_N GPIO13
DCD_N GPIO12
DTR_N GPIO11
RXD GPIO10
CTS_N GPIO09
TXD GPIO08
RTS_N GPIO07
This patch applies 3'b101 mode to UARTF:
GPIO14
GPIO13
GPIO12
GPIO11
RXD
CTS_N
TXD
RTS_N
Because the base rt5350.dtsi file forces 3'b000 mode, remove the pin setting from this file and apply it directly to the files that inherit from it (WIZFI630A.dts and WT1520.dtsi). This change makes the rt5350.dtsi file consistent with the mt7620a.dtsi file.
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48665
The I2C function of the RT5350 SoC on the HLK-RM04 is used for GPIO1 and GPIO2.
Take note that the I2C_SD pin is GPIO1 on the RT5350 and is exposed on the HLK-RM04 as GPIO0
Likewise the I2C_SCLK pin is GPIO2 on the RT5350 and is exposed on the HLK-RM04 as GPIO1
group mode 1 mode 2 hlk-rm04 pin & export
i2c i2c_sd gpio1 (pin 8, hlk-rm04:gpio0)
i2c i2c_sclk gpio2 (pin 9, hlk-rm04:gpio1)
reference:
http://www.hlktech.net/product_detail.php?ProId=39http://cdn.sparkfun.com/datasheets/Wireless/WiFi/RT5350.pdf
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48664
The RESET button of the HLK-RM04 is connected to GPIO0, linux function 0x198
The WPS button of the HLK-RM04 is connected to GPIO14, linux function 0x211
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48663
The power LED on the HLK-RM04 is hard wired to the power bus and is not under GPIO control, remove the bogus config for it.
(Note that GPIO0 is actually connected to the RESET button.)
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48662
With the backport of the kernel 4.5 pinctrl-xway patches (3551609d &
826bca29) the pinmux group "spi" was splitted into "spi_di", "spi_do" &
"spi_clk". But the no longer existing group "spi" is still used by some
device tree source files.
This fixes the detection of the wireless chipset of the VGV7510KW22.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48658
The stock u-boot doesn't disable unused flash banks. Therefore, the nand
driver tries to initialize a not connected NOR flash and the device
hangs on boot.
Workaround the issue by selecting the second flash bank (NAND).
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48657
When dealing with Broadcom hardware we can simply use swconfig's generic
helper, we just need to do some validation of requested state.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48623
Thanks to this change swconfig can access port PHYs e.g. when setting
port link state with a generic helper.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48622
It's quite common for switches to have PHY per port so adding a generic
helper setting link state will help many drivers. It just needs an API
to access PHYs which this patch also adds.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48621
Some D-Link routers (e.g. DIR-885L) have NAND and use Seama format. It
means OpenWrt will want to have UBI in Sseama entity and should be able
to detect it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48600
Our mtdsplit parsers may want to create partition with name choice based
on partition file system (e.g. SquashFS vs. JFFS2). This patch allows
passing extra argument pointing to variable that will be set properly.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48598
All other SoC types are using "lantiq,sram" and "simple-bus" to ensure
that all child nodes are set up correctly during linux kernel
initialization (plat_of_setup(void) in arch/mips/lantiq/prom.c). Without
this some of sram child nodes might not be parsed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48548
This removes a lot of duplicate register and interrupt definitions by
moving the xrx200-net definition to vr9.dtsi and making all devices re-
use it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48547
Linux now has device tree support for malta. The patch for correcting
/proc/iomem content is not needed now. Previously it was
root@(none):/# cat /proc/iomem
00000000-00000fff : reserved
00001000-000effff : System RAM
000f0000-000fffff : reserved
00100000-0fffefff : System RAM
00100000-003f2b6b : Kernel code
003f2b6c-00485937 : Kernel data
...
Now it's
root@OpenWrt:/# cat /proc/iomem
00000000-0fffefff : System RAM
00100000-004a3297 : Kernel code
004a3298-0057cfff : Kernel data
...
The kernel config was prepared as follows
1. cp target/linux/malta/config-{3.18,4.4}
2. make kernel_menuconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 48543
Initially 4.4 didn't work on bcm53xx because network was breaking few
seconds after setting interfaces. It's fixed since r48059 (switching
from 4.4-rc5 to 4.4-rc7).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48510
Rename kernel_size variable as it includes whole entity size, not just a
kernel size. Also update comments to match it and describe better what
are we checking/looking for.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48480
The new .abiflags section was kept, pushing the appended arguments to
the wrong offset and causing it to read the section instead, making
it fail on boot.
Fix this by dropping this section as well as the other sections.
Closes#21679.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48474
Directly return the return value of genl_register_family_with_ops()
instead of storing it in a temporary variable, then returning it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48472
This reverts commit r48335
The workaround is incomplete and cannot cover all possible cases. The
only real solution to this problem is to disable this feature on
ARM11MPcore entirely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48460
This reverts commit r48276.
This can overwrite the caldata_backup partition, so the layout needs to
be changed in a different way.
Thanks to Arjen de Korte for spotting the issue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48456
r48337 unfortunately incorrectly changed the boardname of the stg212
into stg-212 which is not the name of the image of DTS file or
boardname using sysupgrade, which is 'stg212' and imho should stay
that way.
The changes r48337 made for pogoplug-pro and pogoplug-v3 were correct,
thus this commit only partially reverts r48337.
Also properly set default for USB LED while already at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 48398
r48381 added CONFIG_MTD_SPLIT_UIMAGE_FW=Y to the lantiq kernel
configuration. That unfortunately contains a typo since the "y" has to
be lower-case. This leads to the kernel asking whether the config
symbol should be enabled and thus breaking the build.
FIXES: r48381/feab990887b4: lantiq: Enable the uImage mtd splitter
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48389
Until linux 4.1 the lantiq target used CONFIG_MTD_UIMAGE_SPLIT=y. That
option however is only available until linux 4.3 - thus it was not added
to lantiq's 4.4 kernel config (in r48307). This results in broken images
for devices which are using uImages. This fixes#21652
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48381
The bootloader was updated and now uses 115200 instead of 57600 baud
for the serial console. Change this also in OpenWrt's DTS, so the rate
is consistent for bootloader and linux kernel output.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 48359
The image name for the HiLink HLK-RM04 module has a typo and should read "RM04" rather than "RM02"
Signed-off-by: John Clark <inindev@gmail.com>
SVN-Revision: 48355
As the Default profile option is a legacy subtarget, the dtb for the
sama5d3_xplained board DTS is not built and image generation fails.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
SVN-Revision: 48351
Add a package for a missing module for the at91 high speed device.
Without this the build process pauses asking to build as module.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
SVN-Revision: 48350
This puts the existing patches and config in a 3.18 folder and introduces
a 4.4 config and patches.
The USB clock fix patch is no longer necessary, and the patches applying
to non DT boards has been dropped as the platform has been converted.
4.4 config was generated by copying 3.18 and running make kernel_menuconfig,
scripts/kconfig.pl filled in the gaps.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
SVN-Revision: 48349
This adds basic support for TP-Link VR200v.
Currently the following parts are not working: FXO, Voice, DECT, WIFI (both)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48328
Most of currently mentioned CFLAGS in arc770/Makefile
are not really required because:
[1] "-Os -pipe" are set by default in include/target.mk
[2] "-fno-caller-saves" gets enabled via menuconfig
as an extra compiler flag for developers
So the only one that makes sense is "-matomic" and
that one is really essential. Without it many software
packges won't build complainin on unresolved atomic ops.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48326
While bumping kernel version kernel command line was
unintentionally modified in attempt to make it closer
to upstream version.
In case of AXS that has not only serial port but HDMI/USB
both capable of being debug console we have 2 entries in
kernel's command line:
------------------->8-----------------
console=tty0 console=ttyS3,115200n8
------------------->8-----------------
But as it turned out OpenWRT uses procd as init instead of
Busybox. And in its turn procd gets the first "console"
entry from kernel command line (/proc/cmdline) and uses it
if default inittab is used:
------------------->8-----------------
...
::askconsole:/bin/ash --login
------------------->8-----------------
So what we got is non-functional serial console.
That change removes "console=tty0" which brings serial
console back to life.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48325
The following patches were dropped because they are already applied
upstream:
- 0038-MIPS-lantiq-fpi-on-ar9.patch
- 0039-MIPS-lantiq-initialize-usb-on-boot.patch
- 0042-USB-DWC2-big-endian-support.patch
- 0043-gpio-stp-xway-fix-phy-mask.patch
All other patches were simply refreshed, except the following:
- 0001-MIPS-lantiq-add-pcie-driver.patch
Changes to arch/mips/lantiq/xway/sysctrl.c (these changes disabled
some PMU gates for the vrx200 / VR9 SoCs) were removed since the
upstream kernel disables unused PMU gates automatically (since
95135bfa7ead1becc2879230f72583dde2b71a0c
"MIPS: Lantiq: Deactivate most of the devices by default").
- 0025-NET-MIPS-lantiq-adds-xrx200-net.patch
Since OpenWrt commit 55ba20afcc2fe785146316e5be2c2473cb329885 drivers
should use of_get_mac_address(). of_get_mac_address_mtd is not
available for drivers anymore since it's called automatically within
of_get_mac_address().
- 0028-NET-lantiq-various-etop-fixes.patch
Same changes as in 0025-NET-MIPS-lantiq-adds-xrx200-net.patch
While refreshing the kernel configuration SPI support had to be moved to
config-4.4 because otherwise M25P80 was disabled.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48307
AP148 uses lowercase name as boardname, so we need to use this in
platform.sh as well.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48304
Overwriting static strings is never a good idea, especially expecting
identical strings to be stored in different memory locations.
This caused the lookups to always return the second chip's name. Fix
this by just initializing the lookup with the right values, so we
don't need to modify the strings at all.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48303
BCM531x5 has two pontential cpu ports, and header mode can be enabled
independently on both.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48302
Re-defining the compatible property is not required since the correct
value is inherited from vr9.dtsi.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48295
Compared to the "old" driver:
- Each device must assign a pinctrl setting to the SPI node to allow the
new SPI driver to configure the SPI pins.
While here we are also using separate input and output settings so we
are independent of whether the bootloader configures the pins correctly.
- We use the new "compatible" strings to make the driver choose the
correct number of chip-selects for each SoC.
- The new driver starts counting the chip-selects at 1 (instead of 0, like
the old one did). Thus we have to adjust the devices accordingly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48293
The new driver provides a few improvements over the old one:
- Separate compatible strings per SoC type (this allows removing some
hardcoded of_device_is_compatible() checks)
- It does not rely upon spi-bitbang anymore
- chip-selects are numbered as in the datasheet (= starting at 1 instead
of 0)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48292
All devices are now using the HW SPI driver, so this is not necessary
anymore.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48291
This allows devices to use SPI without having to re-define (and thus
duplicating) the whole SPI node.
By default SPI is disabled (as before) because only few devices need it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48286
After the latest pinctrl backports there are only 50 (instead of 56 as
before) GPIOs/pins exported (thus the first GPIO on VRX200 SoCs is now
462, before it was 456). This means that any hardcoded GPIOs have to be
adjusted.
This broke the PCIe driver (which seems to be the only driver which uses
hardcoded GPIO numbers), it only reports:
ifx_pcie_wait_phy_link_up timeout
ifx_pcie_wait_phy_link_up timeout
ifx_pcie_wait_phy_link_up timeout
ifx_pcie_wait_phy_link_up timeout
ifx_pcie_wait_phy_link_up timeout
pcie_rc_initialize link up failed!!!!!
To prevent more of these issues in the future we remove the hardcoded
PCIe reset GPIO definition and simply pass it via device-tree (like the
PCI driver does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48285
These were introduced in upstream commit
be14811c03cf "pinctrl/lantiq: introduce new dedicated devicetree
bindings" and finally allow us to use the individual pins within our dts
(for example spi_clk, etc.).
Please note that this changes the number of GPIOs which are available for
some SoCs. VRX200 SoCs for example only have 50 pins, but previously 56
pins were exposed. This means that all places which are using hardcoded
GPIO numbers (which are not passed via device-tree) need to be adjusted
(because the first GPIO number is now 462, instead of 456).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48284
Upstream commit be14811c03cf2 "pinctrl/lantiq: introduce new dedicated
devicetree bindings" allows us to use each pin in the pinmux. This is
useful for example in the "spi" group which contains some pins which
are inputs, and some which are outputs.
These can only be used once the new compatible strings for the pinctrl
node are used.
Additionally 0150-lantiq-pinctrl-xway.patch and the "GPIO PORT3 fix"
(which was part of 0012-pinctrl-lantiq-fix-up-pinmux.patch) were
replaced with their upstream variants which are also in 4.5.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48283
According to the calling convention of the o32 ABI the caller
function must reserve stack space for $a0-$a3 registers in case
the callee needs to save its arguments.
The assembly code of the loader does not reserve stack space for
these registers thus when the 'loader_main' function needs to save
its arguments, those will be stored in the 'workspace' area instead
of the stack.
Because the workspace area is also used by other part of the code, the
saved register values gets overwritten and this often leads to failed
kernel boots.
Fix the code to reserve stack space for the registers to avoid this
error.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 48279
Change MTD on WNDR4300 and WNDR3700v4 to fully utilize the 128MB flash.
Credit to @Tuochenlyu on GitHub.
Signed-off-by: Chris Marchesi <chrism@vancluevertech.com>
SVN-Revision: 48276
PTP requires at least one timer to be 1PPS so describe it.
For testing, load kernel module gianfar_ptp and use ptp4l
from linuxptp.
Copied from FSL P1010RDB reference design.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
SVN-Revision: 48275
The old signature only worked because brnboot ignores the leading "5" in
the signature. We can see the correct signature when flashing a brnImage
via recovery web-interface, in this case brnboot reports:
[CGI-Signature Check] buf:[BRNDA6431], sigInFlash:[BRNDA6431]
Thanks to Mathias Kresin for reporting this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48269
This add support for IGMP Snooping on atheros switches (disabled by default),
which avoids flooding the network with multicast data.
Tested on TL-WDR4300: disabling IGMP Snooping results in multicast flooding
on each specific port, enabling it back again prevents each port from
receiving all multicast packets.
Partially based on: http://patchwork.ozlabs.org/patch/418122/
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48268
- random-bcm2708 and spi-bcm2708 have been removed.
- sound-soc-bcm2708-i2s has been upstreamed as sound-soc-bcm2835-i2s.
Let's keep linux 4.1 for a while, since linux 4.4 appears to have some issues
with multicast traffic on RPi ethernet:
https://gist.github.com/Noltari/5b1cfdecce5ed4bc08fd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48266
This removes the arch-specific mtdsplit parsers and enables the generic
implementations for brnImage, EVA and TP-Link instead.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48264
On most image types the rootfs ends at an erase-block. However, at least
with brnImages this is not the case: while the partitions are aligned
with the erase-block size there is a 12 byte footer at the end of the
partition which must not be touched by any filesystem. This lead to a
rootfs_data partition which was not aligned properly (and thus ended up
being readonly):
0x000000480000-0x00000085a800 : "rootfs_data" (128 KiB EB)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48263
This allows splitting EVA images (usually found in fritz devices). The
firmware will be split into a kernel and a separate rootfs partition.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48262
This adds brnImage (used with the brnboot bootloader) firmware parsing
support. brnboot verifies the integrity of the firmware stored on the
"Code Image" partitions by looking at the 12 byte footer at the very end
of the partition. This footer contains the checksum of the original
brnImage (kernel + rootfs/squashfs) and must not be touched (by our JFFS2
rootfs_data - otherwise the image will not be bootable anymore).
Big thanks to Mathias Kresin for analyzing the brnImage structure and
finding out the information how to keep images valid even when adding a
nested rootfs_data partition.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48261
Given those patches are relevant to any ARC platform and even
ISA version it makes perfect sense for patches to exist
in one place instead of being duplicated for each new ARC-based ASIC.
Note this is a prerequisite for upstreaming of ARC HS38 support in
OpenWRT.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48241
This switch involved:
[1] Regeneration of config (few options went away)
[2] Regeneration of patches so they apply cleanly (different offsets)
[3] Update of .dts files because we now explicitly specify
memory regions in use as opposed to previously used offset
from 0x8000_0000
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48240
This patch was merged into upstream Linux 4.1.
This fixes#21587 and was introduced in r48223.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48229
Fully reset the chip like on a full up/down, but without the PHY
statemachine restart.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48228
This removes one patch which was applied upstream with commit
67b9bcd36906e12a15ffec19463afbbd6a41660e. All other patches were
refreshed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48203
Some switches can force link speed for a port. Let's add API that will
allow drivers to export this feature.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48142
With the default network config provided by package base-files present,
board_detect won't create a new config from board.json.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 48076
My last bugfix (r47538) introduced a new bug in wndr3700_board_detect
(again...).
Assigning the result of ar71xx_get_mtd_offset_size_format to the model
variable before stripping of garbage using awk will cause all NUL bytes to
be removed before awk is applied, leading to model strings like
"NETGEAR WNDRMACv2NETGEAR", where a NUL byte after the v2 is supposed to
terminate the string.
Fix by calling ar71xx_get_mtd_offset_size_format twice, once piping to awk
directly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48075
This fixes regression introduced in my recent ledtrig-netdev commit.
Events triggered by different interfaces were stopping timer so it
wasn't working for tx/rx mode.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48072
It was never tested, most likely not working (because of le32_to_cpu)
and not upstreamed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48060
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
linux 4.4 (since commit 08b3c894e56580b8ed3e601212a25bda974c3cc2
"MIPS: lantiq: Disable xbar fpi burst mode") requires that the xbar is
defined in the .dts of vrx200 (VR9) SoCs.
SVN-Revision: 48056
LED's were defined wrong in the device tree file, they are hardware driven because they are connected directly to the switch chip and wireless chips respectively, thus no GPIO addresses are assigned to them. It is safe to remove them from the device tree file to stop confusion.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 48055
The ppp0 interface is renamed after the connection is established. Due
to a missing NETDEV_REGISTER event, the ledtrig-netdev isn't aware of
the renamed interface and literally ignores the device
(no tx/rx indication, led isn't switched off with 'ifdown wan').
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48048
The P2812HNU-F3 doesn't have usb leds. Only the P2812HNU-F1 has those
leds.
Reported-by: Sylwester Petela <sscapi@gmail.com>
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48043
The leds of the following boards are not renamed due to lack of
manuals/informations:
- ARV7519PW
- ARV7510PW22
- ARV4510PW
The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't
match the leds from the manual or pictures (e.g. there shouldn't be a wps led).
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48042
The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to
indicate the current boot state. This patch adds support for such cases.
The existing led sequences should be the same as before.
Boards which are using a led different from power (like TDW89x0) are
changed to switch of the led after boot
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48041
dsl_control (dsl_notify.sh) is the only process which is aware of the
state of the atm/ptm interface. Use the dsl led exclusive for the dsl
line state.
On boards which don't have a distinct internet and a dsl led, let the
netdev status of the atm interface trigger the shared led.
Triggering the shared led according to the status of the ppp interface
isn't suitable, since the led would be switched of if the ppp
connection goes down, but the line is still in sync.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48040
Remove all now double defined leds from the led board file. Use pppoe
as default for all broadband connections, since it's the default in
OpenWrt now.
Rename the the wifi leds to make sure, the not applicable default
values get overwritten.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48038
- ARV7525PW: use the power led as dsl led as done by the stock firmware
- FRITZ3370: use the info led as internet led
- FRITZ7320: use the power led as dsl led as done by the stock firmware
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48037
Use the same led logic and labels as the OEM firmware (red = okay,
blue = failure).
Add the red internet led.
Remove missing usb led workaround. The workaround shouldn't be in the
default configuration.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48036
No need to switch (and keep) on all leds at boot. Use the same led
logic and labels as the OEM firmware (red = okay, blue = failure).
Add the red internet led.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48035
Change the name of the .ubi produced to strip out the word 'factory'. This is
mainly due to the fact that there is no difference between the Ventana 'factory'
image vs the standard image.
Name changes from:
openwrt-imx6-ventana-squashfs.nand-factory_<size>.ubi to
openwrt-imx6-ventana-squashfs-nand_<size>.ubi
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48016
Some Ventana boards have a Marvell sky2 GigE controller as eth1 however
assigning the mac address through device-tree is difficult because the
PCI slot can move around depending on board configuration and slot population.
To work around this we add a patch to the sky2 driver to allow accessing its
mac address via a device-tree alias.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48013
On Ventana boards the Gateworks System Controller is the only device on I2C1
(/dev/i2c-0) and it can NAK transfers if it is busy in an ADC loop. Because
this is a multi-function device with several slave addresses it is best to
add retries at the controller level instead of within each slave driver. This
adds a patch that adds 3 retries for i2c transactions only for Ventana boards
and only for I2C1
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48012
This is a backport of a2291badc355d58ead5c19ae0609468947416040 from thermal-soc
accepted upstream.
The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP. Instead
of assuming 85C for passive cooling threshold and 100C for critical base
these thresholds off the thermal gade max CPU temperature:
- passive threshold: max - 10C
- critical threshold: max - 5C
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 48011
Certain board revisions of the GW52xx support an SPI host controller with
a single chip-select going to an off board connector.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48009
As explained earlier, using SWITCH_TYPE_LINK gives more flexibility,
it doesn't require e.g. string parsing to read some data.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47999
So far we were sending link data as a string. It got some drawbacks:
1) Didn't allow writing clean user space apps reading link state. It was
needed to do some screen scraping.
2) Forced whole PORT_LINK communication to be string based. Adding
support for *setting* port link required passing string and parting
it in the kernel space.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47997
It's not necessary to define PCI_* if pci_ids.h is included a few
lines above.
The change to pci_ids.h doesn't look intentional to me, especially
since the former value is added to the top of ifxmips_fixup_pcie.c.
Both changes were introduced with the kernel 4.1 support patches and
were not present in the 3.18 patches.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47996
Use the same max spi frequency as set in u-boot.
According to the datasheets, the Q64-104HIP as well as the Winbond
25Q64FVSIG support spi frequencies up to 50 MHz. During my tests, the
Q64-104HIP couldn't be recognized/initialized if the frequency
was > 40MHz.
Both chips do support fast read as well.
While touching the dts file, I fixed the dtc compiler warnings.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47994
using the special tag in this way lead to port mirroring for certain types of traffic.
fallback to using th PMAC_EWAN register for the wan portmap.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47993
Previously switching to non-existing device (interface) could result in
leaving LED on.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47990
We may just delete timer on every trigger update and then start it again
if needed. This will let us avoid both: races and locking in frequently
called timer callback.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47987
Read/write lock was adding useless complexity, there wasn't any real
gain in case of this driver.
Also switch to _bh variants to avoid deadlocks.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47986
