The boot loader of many boards provides a kernel boot argument with a
broken console parameter to the kernel. This will be taken before the
stdout-path defined in device tree and the serial will not work on this
board. Multiple boards are affected by this problem, so revert this
patch for all boards. Later we can remove the boot arguments from the
device tree again, after the individual board was checked to work.
This partly reverts this commit:
commit 4995c64857
Author: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Date: Sun Dec 11 21:55:00 2016 +0100
lantiq: specify console using stdout-path instead of cmdline argument
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following commit changed the build templates name but forgot to
update the TARGET_DEVICES variable properly.
commit f9226158be (lantiq: rename EASY98000 to EASY98000NOR)
Signed-off-by: John Crispin <john@phrozen.org>
The power LED can not be used for indicating the xDSL line state and
the in system (boot) state at the same time in LEDE. As soon as the
xDSL Line goes down, the power LED is switched off.
During xDSL handshake the power led would blink with the same or a
similar pattern as during boot.
Both might confuse users.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to a hardware bug of Atheros 8030 phys, the driver need to reset
the phys on link state change.
Use the correct compatible string for the at903x phys connected to
switch port 0 and 1.
Fix the pinmux of the gpio lines connected to the reset pin of the phys
and define the reset-pins to let the driver do the fixups.
Fixes FS#343
Signed-off-by: Mathias Kresin <dev@kresin.me>
/etc/preinit has been the default init-script for a very long time (at
least since Linux 2.6.30 in OpenWrt). Remove the kernel command line
"init" parameter to get rid of duplicate and inconsistent definitions
of this parameter (some boards, like FRITZ3370 for example did not use
it at all, while it's just copy and paste on others).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Use devicetree's /chosen/stdout-path instead of the kernel command line
(embedded in the .dts-files) to specify the serial console. Using the
chosen node is recommended on devicetree based platforms.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This attribute is not evaluated any more and the boot loader on these
reference boards does not provide a broken root= or console= parameter.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add an extra function to patch the mac and fixup the checksum
afterwards. Calculate the checksum position automatically. The offset
to the mac address is the same for all checksum protected EEPROMs.
No EEPROM requires a byte swapped mac address. The mac byte swap code
was required due to an bug in the script that is now fixed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The EEPROM data in the flash of the ARV7518PW, ARV8539PW22,
BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning
that for example the ath9k base_eep_header fields "version" (high and
low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are
just 1 byte wide, thus their position is swapped).
The old "ath,eep-endian" property enabled the corresponding swapping
logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is
based on the magic bytes in the EEPROM data which have nothing to do
with the calibration data - thus this logic should not be used
anymore).
Since we have switched to the upstream ath9k devicetree bindings there
is no binding anymore which enables swab16 in ath9k (as this logic is
not recommended anymore as explained above), leading to ath9k
initialization errors:
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
(this shows that the version field is swapped, expected values are VER
0x000E and REV 0x0001)
Swapping the ath9k calibration data when extracting it from the flash
fixes the devices listed above (all other devices do not require
additional swapping, since the position of the fields is already as
expected by ath9k). This allows ath9k to read the version correctly
again, as well as the more important "eepmisc" field (which is used for
determining whether the data inside the EEPROM is Big or Little Endian
which is required to parse the EEPROM contents correctly).
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Refresh patches on all 4.4 supported platforms.
077-0005-bgmac-stop-clearing-DMA-receive-control-register-rig.patch
removed as now upstream.
Compile & run tested: ar71xx - Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ifxhcd never had roothub support but since kernel 3.x it was expected
that a roothub always exists.
The patched fixed a null pointer deref in the usb subsystem because of
the missing roothub.
Since ifxhcd is gone, this whole patch isn't required any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This way the on nand bad block table is preserved and used. Add support
for nand OOB ECC checksums as well. It should fix all reported ubi
errors, which were all related to bad nand blocks and a purged on nand
bad block table.
The existing ubi partition will be reused, which eliminates the need
to touch the caldata during initial install. The BT u-boot has support
for loading a kernel from an ubi volume. It isn't necessary any longer
to replace the BT u-boot with a custom compiled one to use LEDE.
It is required to restore the BT Firmware and install LEDE from scratch
to switch to the new partition layout.
An image for restoring the BT firmware and installing LEDE is provided
at https://github.com/mkresin/lede/releases.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport upstream commit a61ae81a1907af1987ad4c77300508327bc48b23.
The actually purpose of the patch was to do some cleanup. As a side
effect of this cleanup, the device node is now passed to nand_dt_init.
This allows to use the common nand device tree properties
- nand-bus-width
- nand-on-flash-bbt
- nand-ecc-mode
- nand-ecc-step-size
- nand-ecc-strength
for the plat_nand driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the addition of the bindings to the ath9k driver, this code
isn't used any longer. The fixup is now done by the owloader.
Rename the ath_eep.c file to ath5k_eep.c to indicate that this files
includes ath5k related code only.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.
The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds support for the Intel Falcon SoC for GPON.
Support for the Falcon SoC was removed in commit c821836395 svn rev:
40392 from OpenWrt, this commit adds it again.
This patch adds a new subtarget for the Falcon SoC, but it still misses
all the drivers needed to control the GPON part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DEVICE_PACKAGES are not included in the initramfs image in case
TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images
with a not working network configuration because of a missing swconfig.
Workaround the issues by adding the essential swconfig package to the
default packages selection and deselect swconfig for boards not having
swconfig included before via device packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This allows specifying PCI devices as children of the PCIe controller
node to pass configuration data to them.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Parameters for dwc2 on lantiq.
A separate dwc2_core_params structure is defined for danube because danube
fifo sizes are large enough to be autodetected. This is not the case on
arx and vrx.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Device tree binding for dwc2 usb driver on danube.
Leave old ifxhcd-danube driver as an alternative.
Also adds dr_mode = "host" to eliminate warning on boot.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
All compiled device tree files not mentioned are binary identical to the
former ones.
Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts.
Due to the include of the input binding header, the BTN_* node names in:
- ramips/GL-MT300A.dts
- ramips/GL-MT300N.dts
- ramips/GL-MT750.dts
- ramips/Timecloud.dts
will be changed by the compiler to the numerical equivalent.
Move the binding include of lantiq boards to the file where they are
used the first time to hint the user where the values do come from.
Signed-off-by: Mathias Kresin <dev@kresin.me>
As specified by e0229a16b0 if the VR9
based router provides FXS ports and they should enabled then the
following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M
By adding mem= parameter a pci device stop working correctly. The
pci-lantiq.c module use get_num_physpages() to compute dynamically the
memory amount of the board.
The mem= make the module to compute in the wrong way the BAR11MASK, so
in this situation the mask is misaligned with the dma area that the
hardware expects.
This patch is a port of what legacy ifxmips_pci.c does.
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Set a device specific wireless mac address for ARV7506PW11, VGV7519 and
VGV7510KW22. The one from the EEPROM is a generic one and the same on
all boards.
Use the wifi@0,0 label and the pci0,0 compatible string for the
ARV7519PW and ARV7525PW since the pci vendor and device id is unknown.
It should work anyway since the compatible string isn't evaluated
(yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
- remove not existing properties
- remove properties having the same values as the included dtsi
- remove nodes which are disabled in the included dtsi and not enabled
in dts
- replace the deprecated pinctrl-* compatible strings
- use the same labels for nodes as the included dtsi
- move common used vr9 pci properties to vr9.dtsi
- remove the unused stp node from HomeHub 2B devcie tree source file
- fix spaces vs. tabs and remove superfluous linebreaks
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.
Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)
Modified after cherry-pick:
obj in Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756
If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1
To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 8d924d43c0ea6839a3a33e54982e8da48b736001)
Modified after cherry-pick:
compatible attribute
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
This bugfix enables FXS support on dabube based devices.
Changed "compatible" attribute from "vmmc" to "vmmc-xway".
The vmmc driver uses "vmmc-xway".
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Read the temperature including the decimale place from the CGU_GPHY1_CR
register.
Decrement the temperature read from the register by 38.0 degree celsius.
The temperature range of the sensor is -38.0 to +154 °C and the register
value 0 is equal to -38.0 °C. This fixes the report of unrealistic
temperatures as seen on all tested boards.
Give the SoC a few milliseconds to get the first temperature value. On
some rare occasions there is no temperature value in the register when
read the first time after activation. This leads to a reported
temperature of -38.0 °C on boot.
Only version 1.2 of the vr9 SoC has a temperature sensor. Add a check
to make sure the driver doesn't load on v1.1 vr9 SoCs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The device tree file of ARV752DPW uses numbers/hex values for gpio states and input event codes.
This cleans it up and uses the available macros from header files. This way the functions are easier to read and comprehend.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
[sanitize all device tree files]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The GPIO for reset switch is wrong in definition. Further the key codes for the two additional buttons are ineffective.
Both is fixed here.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.
To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:
VR9 # run reset_uboot_config
VR9 # reset
VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The mac address is printed on the label at the bottom of the case.
The following steps are need to be done during first install:
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.
Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.
A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The WBMR boards are the only ones in the whole tree selecting the wpad
and hostapd-utils package by default.
Remove the wps uci-default script as well, there is no obvious reason
why the wps config need to be set only for this board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In case the adsl/vdsl service is disabled intentional, the output is
cluttered with the following message multiple times if the status of
the dsl line is queried:
killall: vdsl_cpe_control: no process killed
If the dsl line status is queried by LuCI, the logfile is spammed with
the message.
Fix the issue by using killall in quite mode. In quite mode killall
still returns a non-zero value if the to be killed process can not be
found so that existing logic based on the return value still works.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the introduced double whitespace the default package selection
isn't applied. This leads to errors like a not working networking
because of a missing swconfig binary.
Fixes FS#208.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add USB led aliases to boards having an led which is meant to be used
as USB led according to the manuals.
Remove the kmod-ledtrig-usbdev from the default package selection for
boards not having an USB led. Add the kmod-ledtrig-usbdev to boards
where it is missing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use a more generic name for the lantiq_get_dt_led_chosen function.
Drop the lantiq_is_dt_led_chosen function. The lantiq_get_dt_led
function can be used to achieve the same.
Signed-off-by: Mathias Kresin <dev@kresin.me>
It missed some changes needed for kernel 4.4. This is only used by the
Falcon SoC and not for the xRX SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Local variable declarations outside of functions are illegal since the Busybox
update to v1.25.0, therfore remove them from the appropriate places.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Backport patches from upstream Linux kernel which are making the
kernel stores the appended dtb not in the same resisters as defined in
the UHI specification, use a separate variable on MIPS.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[some modifications]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- quote the interface name
- remove call of not existing function
- remove the proto if it's the default proto
Signed-off-by: Mathias Kresin <dev@kresin.me>
No functional change, it's just to have the same style everywhere. This
way I don't need to use any regex magic to extract all subtargets for
compile tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add or fix the physical port number of switch ports to allow LuCI to
display the ports in physical order.
Remove the physical port number in case bridge port and physical port
order are the same.
Reorder the ucidef_add_switch parameter to be aligned with the switch
port number.
Remove board settings which are covered by the default case and remove
comments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With 12fe4b5798 I switched the ath5k
eeprom extraction to an alternate code path. Unfortunately this code
seams to be broken since ages and broke the ath5k EEPROM extraction.
Reported-by: Mohammed Berdai <mohammed.berdai@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
GCC treats 24kc and 34kc exactly the same and will generate identical
code, so there is no need to tune to 34kc instead of 24kc.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Device/AVM unconditionally inherits Device/NAND, which changes the
sysupgrade image to sysupgrade-tar (instead of a "raw" sysupgrade image
as used in the Device/Default template).
This moves the Device/NAND call to the FRITZ3370 device definition, as
this is the only AVM/EVA device that uses NAND.
Additionally we have to define the IMAGE_SIZE for the AVM/EVA NOR
devices to ensure that the images are not discarded.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Use priv->wan instead of priv->id as indicator if packets should go to the
Ethernet WAN group (DPID=1) or not (DPID=0). This way, it's independant of
interface names or indexes.
Signed-off-by: Martin Schiller <mschiller@tdt.de>
By default USB LEDs are associated with usbdev trigger. However,
not all devices which have USB LEDs have kmod-ledtrig-usbdev in their
list of default packages. Add it to the relevant devices.
Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
With an own DMA TX channel for each network device (eth0 + eth1) there
won't be any "tx ring full" errors any more.
This patch also move the spinlocks to the channel level instead of locking
the whole xrx200_hw structure.
Signed-off-by: Martin Schiller <mschiller@tdt.de>
According to the author of the cpu temp driver, not all xrx200 boards
have a cpu temperature sensor. For that reason enable the sensor only
for tested boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not set the lan mac address for boards which having the lan mac
address already set in device tree source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The device tree binding and the associated code duplicates functionality
already patched into the etop driver. The compatible string isn't used
any more. Therefore the whole code can be dropped.
The "mac-increment" property allowed to increment a mac address received
via kernel cmdline. This functionality isn't used by any device and
should be added as etop driver device tree property if required again.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the generic mtd-mac-address dts property to get a mac address from
flash instead of the lantiq specific one.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the same mac address increment in device tree source file and
userspace.
Don't add a mac address increment to either the only mtd mac-address or
to all mac-addresses.
Fix a typo in the TDW89X0.dtsi file to add an increment.
Signed-off-by: Mathias Kresin <dev@kresin.me>
All device tree nodes are using the named properties now and the code
path handling the reg property isn't required any more.
The code related to the ath,eep-flash property has been reformatted to
be better readable.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There does not seem to be any meaningful difference in generated code.
This will save some time and space on snapshot builds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The device tree description misses some Ethernet ports and there was no
model specified for this board. In addition there was no switch
specific default configuration created.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Both devices were converted to the new image build code but still using
the LegacyDevice define. Therefore an image isn't created for the
mentioned devices.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specifying the device profile in PROFILES is unnecessary, and for all
devices the DEVICE_PROFILE variable matched the device name.
Get rid of this useless variable and set DEVICE_DTS to $(1)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rename uboot environment partition on BT Home Hub 3A so that mac address
setting works correctly.
Also, the mac address field in the ath9k calibration data is not used,
and should not be referenced in the dts.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
This patch was introduced in commit r16412 for the brcm47xx target only
and then moved to generic in commit r32395. It was initially added
because of ticket #5186 and should fix some problems with fuse file
systems and MIPS caches. The commit comment in r32395 says that this a
generic problem in MIPS CPUs, but does not name any specifics about
that. There was a fix added to kernel 2.6.21 in commit commit
7575a49f20 "[MIPS] Implement flush_anon_page()." that should fix this
problem, but that was already available before both commits were done
to OpenWrt.
I just tested fuse with ntfs.3g without this patch on a BCM4704
(BMIPS3300 V0.6) SoC and haven't seen any problems. Someone reported
that removing this patch improves some fuse operations by 5 times on
some modern MIPS cores.
My test was only a simple "dd if=/dev/zero of=/mnt/zero bs=5000" to an
USB stick.
This patch removes the patch to OpenWrt, because I assume that it is
not needed any more and Felix, the orginal author, also thinks so.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
So far the network in failsafe is setup only for one board. Use the
eth0 interface as lan interface for all boards for now.
If a board has its lan interface(s) on another eth, a special
handling based on the board name can be added.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Ethernet, ADSL2+ and LEDs are fully functional.
Supporting the two TAE ports and SIP gateway was not attempted.
The WiFi is unreliable, due to experimental support for rt35xx family
devices by the rt2800pci driver.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
[rebase to LEDE HEAD]
[switch to normal image instead of brnboot image]
[remove not required pinmux child nodes keys, leds, ebu, exin, pci_in and pci_out]
[remove switch_rst pinmux child node (no support for hw reset in driver/setting a default GPIO value in DT]
[enable usage of the wireless LED]
[fixup mac address configuration]
Sgned-off-by: Mathias Kresin <dev@kresin.me>
The bootloader uses 30 MHz as the SPI frequency for flash on the Germany and
North America models, and 50 MHz for it on the worldwide model, but the Lantiq
SPI driver in OpenWrt and LEDE may access the flash differently such that
writes are capped at 20 MHz, leading to read errors reported on the worldwide
model at 30 MHz.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
The EASY80920 is available with the A1X and the A2X chip version
depending on the board version. Add both firmware versions to device
tree and make the driver load the correct version depending on the chip
version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This image format is used by Lantiq's / Intel's UGW version 6.1 to 7.1.
These images can be flashed onto a board with the SoC vendor boot
loader as a replacement for the vendor firmware.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The lantiq kernel arch code selects CONFIG_RESET_CONTROLLER always, so
it is always selected when the lantiq target is build. we do not need
support for unselected CONFIG_RESET_CONTROLLER option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The restart event code is used in LEDE to trigger a factory reset on
long press as well.
By using the power event code, the restart functionality can be used
without being prone to trigger a factory reset.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch is a follow up to commit 4cf3fd4 "add support for indicating
the boot state using three leds".
At the time of writing the patch, I wasn't aware that it's possible to
switch info failsafe after boot (factory reset).
Enabling the failsafe led without disabling the running led causes an
unexpected led colour on devices using a single multicolour led to
indicate the boot state.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The *_UBIFS_OPTS variables need to be prefixed with DEVICE_ to match
the profile name.
The conditions need to be evaluated after the *_UBIFS_OPTS are set,
otherwise the variables are always empty.
Do not append or pass the DEVICE_ prefixed profile name to the images.
Use the name that is passed by the Image/Build/Profile/ step.
Signed-off-by: Mathias Kresin <dev@kresin.me>
