Replace magic number with the appropriate macro in
avila/ixdp425/miccpt PCI routing setup.
Signed-off-by: Tamas TEVESZ <ice@extreme.hu>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37154
switch buttons should be declared as switch so the failsafe shell is not
triggered by accident in procd
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37131
- Some fixes for the incorrect GPIO assignment of leds on Huawei HW556.
- Addition of unassigned (LAN) leds which can be found on the back of the device.
Signed-off-by: Angga Reza Fardana <angga@norture.com>
Patchwork: http://patchwork.openwrt.org/patch/3744/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37102
This patch enables retrieving the wifi calibration data from an MTD partition.
Try to copy mac address from ethernet before generating a random one.
This fixes DGN3500 ath9k support.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 37087
Trying to load the DEU modules results in unresolved symbols. This
provides them. This requires the previous patch to be applied first.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 37086
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37049
RT305x/RT5350 SoCs require the switch to be reset before touching the ethernet
interface, otherwise the driver will panic.
As we already init the ethernet in preinit we therefor need to reset the switch
before that.
Signed-off-by: Felix Kaechele <felix@fetzig.org>
SVN-Revision: 37027
This patch sets the cflags -mtune=34kc -mdsp only in XWAY subtarget, while the others remain with mtune=mips32r2.
Although the Danube has a Mips 24KEc core performs well with the above cflags.
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 37006
Set mips16 support in XWAY subtarget.
This patch is based in changeset #36600
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37005
Fix EBU leds by removing req2 and gnt2 from pinmux.
Fix rfkill button gpio.
Enable reset button.
Fix power led activation status.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 37004
We currently used 16 DMA Ethernet channels, but the hardware only
supports up to 8 (with 2 per enet and the remaining for USB slave).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36979
Cable modem devices currently poke at some random location in RAM and
may end up having an invalid MAC address which is not suitable. Provide
a default one which is sane.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36957
Cable Modem devices cannot load an ELF file directly so we need to
provide them with a HCS image even when targetting initramfs.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36954
$(KDIR)/vmlinux is already a binary image, there is no need to create
another one.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36949
Use platform data array for storing ath5k EEPROM instead of creating another one.
EEPROM size is 2048 words (2 bytes), so we must read 4096 bytes from flash.
No need to keep the checksum fix now that the EEPROM is loaded completely.
Add a manual eeprom swap for ath9k and keep the endian way.
Use mac-offset property retrieved from the DTS.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 36901
Seems the existing kernel config for 3.8 was cp'ed from 3.7; this patch
is the result of "make kernel_oldconfig" with defaults for new options.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36900
This provides a boot LED sequence suitable for devices with both red and
green LEDs for power. This assumes no "default-on" settings in the
device tree.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36899
This patch adds support for HAME MPR-A2 router using a DTS file.
The platform is Ralink RT5350.
http://wiki.openwrt.org/toh/hame/mpr-a2
Signed-off-by: Dmitry Shmygov <shmygov@rambler.ru>
SVN-Revision: 36898
The TP-LINK TL-MR3220 v2 has a button on the left side
labeled "WIFI". This is GPIO 24. This patch adds the
support for this button.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36848
This patch adds swlib attributes to the RTL8366RB switch/PHY found in the
TL-WR1043ND router that allow to mirror ethernet packets to a monitor port.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36847
submitter was informed of a endinaess swap regression and replied with "works on my board"
revert the patch and make arv7518 wifi work again
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36807
The port 6 of the switch is connected to the SFP
cage on the RB2011*S boards. Add a helper function
to correctly initialize the switch configuration
data on those boards to make the SFP port usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36799
The GPIO buttons of ARV752DPW are active low.
Treating them as active high caused a reboot loop as a reset-button
press is detected by gpio-button-hotplug/gpio-keys-polled on startup.
This fixes: https://dev.openwrt.org/ticket/12642
Signed-off-by: Rafael Gieschke <rafael@gieschke.de>
SVN-Revision: 36783
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 36782
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36781
This patch is a device tree enhancement that IMHO is worthy of mainline.
It allows the bootloader's commandline to be preserved even when the
device tree specifies one.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36780
This patch enables retrieving the wifi calibration data from an MTD
partition. It requires the previous patch.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36779
This postpones the initialization of PCI and wifi until after the MTD
initialization, so that calibration data may be loaded from there.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36778
This reassigns the PPPoE status to the LED that was intended to indicate
it, rather than the DSL sync light.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36777
At offset 0x40, signature for TL-MR10U/TL-MR11U begin
from 0x00, not 0x10/0x11.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36727
MR10U is closer to MR3040 than WR703N. This changes also
enable USB power on GPIO18.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36726
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both
RX and TX traffic from LAN port 1 to LAN port 4:
$ swconfig dev switch0 set enable_mirror_rx 1
$ swconfig dev switch0 set enable_mirror_tx 1
$ swconfig dev switch0 set mirror_monitor_port 4
$ swconfig dev switch0 set mirror_source_port 1
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 36713
* update the bootcode.bin to the newest version
- gpu/cpu mem split is now configured through config.txt, so no need
to create more than one sd card image (just edit the config.txt)
- bootcode.bin now supports the never revision 2 raspberry pis
* add a commented prepopulated config.txt for easier config changes
Taken from <https://github.com/Evilpaul/RPi-config>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36668
Check bootloader argument in mtd.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo@openwrt.org: split into two patches, one for detection,
one letting bcm63xxpart use it.]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36659
Don't build the CRAMFS file system module in the kernel, and save some bytes.
No bcm63xx board needs this obsolete file system, neither those ones using
the Redboot bootloader (liveboxes). Thus, there is no need to build it, since it has
been replaced long time ago by squashfs.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 36616
zsmalloc was changed to a bool because of missing exports in the kernel,
but we already export the required symbol, so change it back to tristate.
Closes#13481.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 36587
This allow us to increase the kernel partition size,
and ensures, that the -factory image still usable via
the original interface.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36584
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36580
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36579
Here is corrected version (only thing not working are wifi LEDs).
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36578
These devices are actually built around the 8devices Carambola dev board.
ARC FreeStation, Flex mARC, iFlex, and SplitStation devices are
supported with this image, see "ARCFlex Firmware Downloads":
http://www.antennas.com/wiki/index.php?title=ARC-OS_Firmware_Downloads_and_Revision_History
Funnily enough if present the external USB wlan ends up being wlan-0, with the
SoC device being wlan-1.
- Invert port map so special handling of vlan config can be removed.
- Add LED config similar to original ArcOS firmware.
- Add GPIO export for enabling PoE passthrough from ethernet port 0 to port 1
- Get MACs from factory partition.
- Update description to list supported devices.
- Carambola uses RT3050 (not RT3052), though my Carambola CPU
actually reports itself as being an RT3350 while still having
RT3050F markings.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 36564
And while at it, also include a define check for BCM6328, thanks to
Gabor for spotting this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36506
Update the numbering of kernel patch for supporting
Netgear WNR2000v3 from 617 to 618.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36498
