Commit graph

1875 commits

Author SHA1 Message Date
Mathias Kresin
01819254af ramips: sound-mt7620: fix dependencies for kernel 4.9
With kernel 4.8 common used code was moved to a shared kmod. Add the
missing dependency to the shared snd-soc-simple-card-utils.ko.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-07 07:56:24 +02:00
Matthias Schiffer
4b32d66216
ramips: simplify ubnt-erx-sfp device definition
Most of the ubnt-erx definition can be reused; the package removals in
DEVICE_PACKAGES have become redundant after d17cb4a68a "ramips: purge
default packages on MT7621".

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-07-06 19:45:09 +02:00
John Crispin
fddc78bc11 ramips: bump to v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-07-06 06:37:03 +02:00
Piotr Dymacz
24043a0d2e ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.

The difference between these two models is in number of available
LEDs, buttons and power input switch.

This work is partially based on GitHub PR#974.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
  switch

* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Factory image notes:

These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.

We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.

Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.

The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".

Flash instruction:

Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

To access U-Boot CLI, keep pressed "4" key during boot.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
c55fadcacb ramips: image: simplify TP-Link Archer devices definitions
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Piotr Dymacz
5b7f592251 build: move mktplinkfw2 related commands to image-commands.mk
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Stijn Tintel
880f73c327 kernel: cleanup CONFIG_SCHED_HRTICK
Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the
generic config in b47fd76563.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-29 04:46:59 +02:00
Mathias Kresin
1faff3b7e3 ramips: add MT7603E driver to AFoundry EW1200
Add the MT7603E driver for the 2.4GHz wireless.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin
3ccca56eb0 ramips: remove optional ucidef_set_led_rssi parameters
The same values are set if the parameters are not specified.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-17 15:38:20 +02:00
Pavlo Samko
82f9486142 ramips: add support for TRENDnet TEW-638APB V2
This patch add support for the TRENDnet TEW-638APB V2.

Specification:
- SoC: Ralink SoC RT3052F
- Flash: 4MB
- RAM: 32MB
- Ethernet: 1x LAN (100 Mbps)
- Wireless: 2.4GHz b/g/n, 2x external antenna
- Buttons: 1x Reset, 1x WPS
- LEDs: Power (green), Ethernet (green), WPS (green and orange),
  Wireless (green)
- UART: 1x UART on PCB (3.3V, GND, RX, TX) - 57600 8N1

Installation

via vendor firmware:
- upload sysupgrade.bin image

via TFTP:
- stop uboot into tftp-load into option "2"
- upload sysupgrade.bin image

Signed-off-by: Pavlo Samko <bulldozerbsg@gmail.com>
2017-06-17 15:38:19 +02:00
小桥
a3332f2aa2 ramips: fix Phicomm K1S(PSG1208) pinmux
Use gpio function for pins with LEDs.

Signed-off-by: 小桥 <29551030@qq.com>
2017-06-12 21:08:54 +02:00
Jo-Philipp Wich
55623a9c83 kernel: update kernel 4.9 to 4.9.31
Fixes the following security vulnerabilities:

CVE-2017-8890
The inet_csk_clone_lock function in net/ipv4/inet_connection_sock.c in the
Linux kernel through 4.10.15 allows attackers to cause a denial of service
(double free) or possibly have unspecified other impact by leveraging use
of the accept system call.

CVE-2017-9074
The IPv6 fragmentation implementation in the Linux kernel through 4.11.1
does not consider that the nexthdr field may be associated with an invalid
option, which allows local users to cause a denial of service (out-of-bounds
read and BUG) or possibly have unspecified other impact via crafted socket
and send system calls.

CVE-2017-9075
The sctp_v6_create_accept_sk function in net/sctp/ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9076
The dccp_v6_request_recv_sock function in net/dccp/ipv6.c in the Linux
kernel through 4.11.1 mishandles inheritance, which allows local users to
cause a denial of service or possibly have unspecified other impact via
crafted system calls, a related issue to CVE-2017-8890.

CVE-2017-9077
The tcp_v6_syn_recv_sock function in net/ipv6/tcp_ipv6.c in the Linux kernel
through 4.11.1 mishandles inheritance, which allows local users to cause a
denial of service or possibly have unspecified other impact via crafted
system calls, a related issue to CVE-2017-8890.

CVE-2017-9242
The __ip6_append_data function in net/ipv6/ip6_output.c in the Linux kernel
through 4.11.3 is too late in checking whether an overwrite of an skb data
structure may occur, which allows local users to cause a denial of service
(system crash) via crafted system calls.

Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-8890
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9074
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9075
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9076
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9077
Ref: https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2017-9242
Ref: https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.9.31

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-06-08 01:03:39 +02:00
Sergey Ryazanov
68e7a2a0b7 kernel: disable CONFIG_SG_POOL by default
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 18:31:10 +02:00
Sven Roederer
9715beb04c ramips: add support for Ubiquiti EdgeRouter X-SFP
This patch adds support for the Ubiquiti EdgeRouter X-SFP and
improves support for the EdgeRouter X (PoE-passthrough).

Specification:
- SoC: MediaTek MT7621AT
- Flash: 256 MiB
- RAM: 265 MiB
- Ethernet: 5 x LAN (1000 Mbps)
- UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
- EdgeRouter X:
  - 1 x PoE-Passtrough (Eth4)
  - powered by Wallwart or passive PoE
- EdgeRouter X-SFP:
  - 5 x PoE-Out (24V, passive)
  - 1 x SFP (unknown status)
  - powered by Wallwart (24V)

Doesn't work:
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.

Installation

via vendor firmware:
- build an Initrd-image (> 3MiB) and upload the factory-image
- initrd can have luci-mod-failsafe
- flash final firmware via LuCI / sysupgrade on rebooted system

via TFTP:
- stop uboot into tftp-load into option "1"
- upload factory.bin image

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2017-06-07 06:33:33 +02:00
Daniel Golle
bfa2e945de ramips: enable PCIe on MT7688
Submitted upstream as well, see
patchwork https://patchwork.linux-mips.org/patch/16223/

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-06-03 20:45:38 +02:00
John Crispin
7f9143168f ramips: add jumbo frame support for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-06-01 12:30:17 +02:00
John Crispin
9bc9457b85 ramips: fixup nand support on v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-06-01 12:30:17 +02:00
Enrico Mioso
acd8649b18 ramips: let the "reserved" MTD partition be RO for R6220
The "reserved" partition should probably be read-only, just in case. Even
not knowing it's content, other devices have marked it as such, so it
seems a good idea to do so also for this device.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Mathias Kresin <dev@kresin.me>
CC: Hanqing Wong <hquu@outlook.com>
2017-05-31 08:45:02 +02:00
Matthias Schiffer
9ab81e63cd
ramips: sysupgrade: move nand_do_upgrade call to platform_do_upgrade
All targets with NAND support should gradually move their nand_do_upgrade
calls from platform_pre_upgrade to platform_do_upgrade.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-05-29 23:50:33 +02:00
Filip Moc
43e4e1f4a5 Move enablemodem from ramips to new package adb-enablemodem and make it used also by TL-MR6400
Signed-off-by: Filip Moc <lede@moc6.cz>
2017-05-27 07:54:40 +02:00
Russell Senior
b76248dd96 ramips: remove fictional LEDs from AsiaRF AWM00x device tree
Neither the AsiaRF AWM002 or AWM003 actually has an LED on the module
board.  The ld1 and ld2 do not represent actual LEDs.  These pins might
connect to LEDS on an eval board or other carrier board, but that is
outside the scope of this device tree file.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2017-05-27 07:01:39 +02:00
Hauke Mehrtens
0b17375931 kernel: update kernel 4.9 to 4.9.30
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-27 00:48:37 +02:00
Kyson Lok
abbfcc8525 ramips: add support for GL-inet GL-MT300N-V2
This patch adds supports for the GL-inet GL-MT300N-V2.

Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)

Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 08:04:15 +02:00
Giuseppe Lippolis
4ba2f4dc63 DWR-512: adding wwan support for the dwr-512 3G modem
This PR allow the 3G modem embedded in the DWR-512 to be managed
by the wwan-ncm scripts. The modem will use the usb-option and
usb-cdc-ether drivers.
The DWR-512 DT is updated accordingly.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-05-25 19:01:08 +02:00
Koen Vandeputte
e842e16f45 kernel: update kernel 4.9 to 4.9.29
- Refresh all patches
- Removed upstreamed
- Adapted 1

Compile tested on: bcm53xx, cns3xxx, imx6, lantiq
Run tested on: cns3xxx & imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[update from 4.9.28 to 4.9.29]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-21 21:51:22 +02:00
Kevin Darbyshire-Bryant
088e28772c kernel: update kernel 4.4 to version 4.4.69
Refresh patches. A number of patches have landed upstream & hence are no
longer required locally:

062-[1-6]-MIPS-* series
042-0004-mtd-bcm47xxpart-fix-parsing-first-block

Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup
as it was incorrectly included upstream thus dropped from LEDE.
As it has now been reverted upstream it needs to be included again for
LEDE.

Run tested ar71xx Archer C7 v2 and lantiq.

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[update from 4.4.68 to 4.4.69]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-05-21 21:48:16 +02:00
Michael Lee
eee09bfe01 ramips: support jumbo frame on mt7621 up to 2k
Signed-off-by: Michael Lee <igvtee@gmail.com>
2017-05-18 14:50:16 +02:00
Steffen Weinreich
e71b2dad94 ramips: add om-watchdog to rut5xx DEVICE_PACKAGES
Add om-watchdog as default package for rut5xx.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
2017-05-15 22:43:33 +02:00
Jo-Philipp Wich
8451b06023 ramips: fixup-mac-address: add missing include
Add missing include of ramips.sh in order to import the missing
ramips_board_name() procedure.

Fixes FS#774.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-05-11 00:52:03 +02:00
Ørjan Malde
5f932988c3 ramips: add support for Asus RT-AC51U
Specification:
 - SoC: MediaTek MT7620A (580 MHz)
 - RAM: 64 MiB (Winbond W9751G6JB-25)
 - Flash: 16 MiB (Spansion S25FL128SAIF00)
 - LAN: x4 100M
 - WAN: x1 100M
 - Others: USB 2.0, reset button, wps button and 9 LEDs

Issues:
 - 5 GHz band is not functional (missing driver support)

Installation:

Asus windows recovery tool:
 - install the Asus firmware restoration utility
 - unplug the router, hold the reset button while powering it on
 - release when the power LED flashes slowly
 - specify a static IP on your computer:
     IP address: 192.168.1.75;
     Subnet mask 255.255.255.0
 - Start the Asus firmware restoration utility, specify the sysupgrade
   image, and press upload

TFTP Recovery method:
 - set computer to a static ip, 192.168.1.75
 - connect computer to the LAN 1 port of the router
 - hold the reset button while powering on the router for a few seconds
 - send firmware image using a tftp client; i.e from linux:
 $ tftp
 tftp> binary
 tftp> connect 192.168.1.1
 tftp> put lede-ramips-mt7620-rt-ac51u-squashfs-sysupgrade.bin
 tftp> quit

Signed-off-by: Ørjan Malde <foxyred333@gmail.com>
2017-05-10 08:45:12 +02:00
Alexey Belyaev
a7cbf59e0e ramips: add new device ZyXEL Keenetic as kn
This device exactly same as NBG-419N but with USB port and USB Led.

Specification:

- SoC: Ralink RT3052 (MIPS24Kc) @384MHz
- RAM: 32 MiB
- Flash: 8 MiB
- WLAN: WiSoC 2T2R/300Mbps (2.4GHz)
- LAN: 4x100M
- WAN: 1x100M
- USB: 1x2.0

Installation via serial console (57600 8N1) from TFTP server
 - rename the firmware to something shorter, for example
   "sysupgrade.bin" (max. 32 chars)
 - copy firmware TFTP server's directory
 - when you power on device, and see U-Boot log, immediatly push "2"
   once.
 - You will see this message:
     2: System Load Linux Kernel then write to Flash via TFTP.
        Warning!! Erase Linux in Flash then burn new one. Are you sure?
 - Push "y", and enter: device IP, then TFTP server's IP, and then
   image firmware file name.

The firmware will be downloaded within ~30 seconds and flashed to the
device (It will take about 2 minutes).

Signed-off-by: Alexey Belyaev <spider@spider.vc>
[squash commits, compact commit message, fix compatible string, remove
superfluous pinmuxes]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-10 08:45:12 +02:00
Sven Roederer
4c3953ba29 ramips: use GPIO_ACTIVE macros in UBNT-ERX.dts
- reorder includes
- use GPIO_ACTIVE_LOW macro instead of hardcoded "1"

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2017-05-06 09:49:00 +02:00
Henryk Heisig
64f2efcdff ramips: strip padding from TP-Link sysupgrade images
This reduce size of sysupgrade firmware.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-05-05 20:02:19 +02:00
Henryk Heisig
cfdd3f260e ramips: add factory firmware for Tp-Link C20i/C50
TP-Link firmware doesn't accept sysupgrade.bin with metadata.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-05-05 20:01:28 +02:00
Daniel Golle
d17cb4a68a ramips: purge default packages on MT7621
In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.

Hopefully fixes FS#758

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-05-04 14:13:23 +02:00
Paul Spooren
414b65db85 ramips: enable ramdisk for mt7621
Fixes #758

Signed-off-by: Paul Spooren <paul@spooren.de>
2017-05-04 00:51:05 +02:00
Jo-Philipp Wich
a45cde9118 ramips: ZTE-Q7: fix switch driver initialization in DTS (FS#716)
Add the changes suggested by FS#716 to fix the switch driver initialization
on the ZTE Q7.

Also remove the `pinctrl-names` field obsoleted by the changes.

Reported-by: Harry Lau <harrylwc@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-04-27 10:44:28 +02:00
Mathias Kresin
3a2cc2c8ad ramips: fix syntax error in board.d/01_leds
Fixes the following error:

  syntax error: unexpected newline (expecting ")")

Fixes: FS#739

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-27 09:39:34 +02:00
Mathias Kresin
bd2727fb25 ramips: ZBT-WE826: include the correct dtsi
Fix a copy/paste error and include the ZBT-WE826 dtsi instead of the
ZBT-WG3526 one.

Fix the syntax error in the ZBT-WE826 dtsi to prevent an compile error.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-27 09:39:34 +02:00
Mathias Kresin
725238f698 ramips: use the ZBT-WE826 power LED for status indication
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
2ddaf96a77 ramips: add ZBT-WE826 32MB variant
The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the
device tree source file, rename the currently supported 16 MByte
version and add the 32 MByte variant.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
3cfc909c54 ramips: rename Digineo AC1200 Pro to ZBT-WG3526 32MB
The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with
unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and
add the sdhci kernel module to use it for multiple clones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Mathias Kresin
619d68bfc9 ramips: prepare ZBT-WG3526 for hardware variants
The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the
current supported 16MByte version to indicate which flash size variant
is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-25 19:29:59 +02:00
Jiawei Wang
ff258effd5 ramips: add support for ZBT-WE1326
Specification:
- SoC: MT7621AT, MT7603EN and MT7612EN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 512 MiB (EM6GE16EWXD-12H)
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Others: USB 2.0, micro SD slot, reset button and 8 x LEDs

Issues:
- Two LEDs for 2.4 GHz and 5 GHz Wi-Fi do not work, can't find GPIOs.
- The pwr LED is not GPIO controllable

How to install:
- The original firmware is OpenWrt, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Signed-off-by: Jiawei Wang <buaawjw@gmail.com>
2017-04-25 19:29:59 +02:00
Alexey Belyaev
187624f759 ramips: fix ZyXEL Keenetic Omni/Omni II GPIOs
Each GPIO bank has only 24 gpios. Use and enable the correct banks for
GPIOs > 24.

Signed-off-by: Alexey Belyaev <spider@spider.vc>
2017-04-25 19:29:59 +02:00
Alexey Belyaev
3549bad814 ramips: fix ZyXEL Keenetic Omni switch config
The wan port is connected to switch port 0. Fix the mediatek,portmap as
well as the default switch config.

Signed-off-by: Alexey Belyaev <spider@spider.vc>
2017-04-25 19:29:59 +02:00
Matthias Schiffer
411c1b64f0
ramips: update DEVICE_PACKAGES for Ubiquiti EdgeRouter X
Fixes removal of unneeded kernel modules with per-device rootfs.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-04-22 18:55:22 +02:00
Daniel Golle
f66e7cb30b ramips: add former board names to PSG1218 variants
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-04-21 14:52:46 +02:00
Mathias Kresin
18618695ae ramips: dont replace the board name
Use fixed led names and add each board variant instead of manipulating
the board name.

It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-21 07:47:59 +02:00
Mathias Kresin
9e468f7829 ramips: add former used board names to metadata
We need to keep the former used (unmodified) boardname in the metadata.
Otherwise an upgrade from an board using the old boardname will be
refused.

Fixes: a75ce960ac ("ramips: use different board names for variants")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-04-21 07:47:59 +02:00