openwrtv4/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7320.dts
Hauke Mehrtens 6eaf8b3d89 lantiq: kernel 4.14: update dts files
Updated the devicetree source files to make use of the following
upstreamed drivers:

 - xrx200 ethernet phy
 - reset controller unit
 - dwc2
 - fpi

Use our custom xrx200 ethernet phy compatible to support boards, which
have switched the vr9 revision during lifetime, with a single devicetree
source file.

By switching to the dwc2 driver + usb phy framework, we don't need to used
our custom gpio power patch and can use a fixed regulator instead.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00

163 lines
2.8 KiB
Text

/dts-v1/;
#include "ar9.dtsi"
#include <dt-bindings/input/input.h>
/ {
compatible = "avm,fritz7320", "lantiq,xway", "lantiq,ar9";
model = "1&1 HomeServer";
chosen {
bootargs = "console=ttyLTQ0,115200";
};
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-internet = &info_green;
led-dsl = &power;
led-wifi = &wlan;
};
memory@0 {
reg = <0x0 0x4000000>;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
#address-cells = <1>;
#size-cells = <0>;
poll-interval = <100>;
rfkill {
label = "rfkill";
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
dect {
label = "dect";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_PHONE>;
};
};
gpio-leds {
compatible = "gpio-leds";
power: power {
label = "fritz7320:green:power";
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
voice {
label = "fritz7320:green:fon";
gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
};
dect {
label = "fritz7320:green:dect";
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
};
wlan: wlan {
label = "fritz7320:green:wlan";
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
};
info_green: info_green {
label = "fritz7320:green:info";
gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
};
info_red {
label = "fritz7320:red:info";
gpios = <&gpio 45 GPIO_ACTIVE_LOW>;
};
};
};
&gpio {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
pci {
lantiq,groups = "gnt1", "req1", "req2", "req3", "req4", "gnt2", "gnt3", "gnt4";
lantiq,function = "pci";
};
pci-in {
lantiq,groups = "req1", "req2", "req3", "req4";
lantiq,output = <0>;
lantiq,open-drain = <1>;
lantiq,pull = <2>;
};
pci-out {
lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4";
lantiq,output = <1>;
lantiq,pull = <0>;
};
};
};
&gsw {
phy-mode = "mii";
mtd-mac-address = <&ath9k_cal 0xa91>;
mtd-mac-address-increment = <(-2)>;
};
&localbus {
nor@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x1000000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
ath9k_cal: partition@0 {
label = "urlader";
reg = <0x00000 0x20000>;
read-only;
};
partition@20000 {
label = "firmware";
reg = <0x20000 0xf60000>;
};
partition@f80000 {
label = "tffs (1)";
reg = <0xf80000 0x40000>;
read-only;
};
partition@fc0000 {
label = "tffs (2)";
reg = <0xfc0000 0x40000>;
read-only;
};
};
};
};
&pci0 {
status = "okay";
req-mask = <0xf>;
gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
wifi@0,0 {
compatible = "pci0,0";
reg = <0x7000 0 0 0 0>;
qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
};
};
&usb_phy0 {
status = "okay";
};
&usb0 {
status = "okay";
};