1447784a8c
Add patches for 4.14, undoing upstream changes for Linksys devices regarding DSA. Instead, the switchdev driver marvell,88e6171 is used. Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> Tested-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
121 lines
2 KiB
Diff
121 lines
2 KiB
Diff
--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
|
|
+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
|
|
@@ -69,9 +69,18 @@
|
|
};
|
|
};
|
|
|
|
- dsa {
|
|
- status = "disabled";
|
|
+ mvsw61xx {
|
|
+ compatible = "marvell,88e6171";
|
|
+ status = "okay";
|
|
+ reg = <0x10>;
|
|
+
|
|
+ mii-bus = <&mdio>;
|
|
+ cpu-port-0 = <5>;
|
|
+ cpu-port-1 = <6>;
|
|
+ is-indirect;
|
|
+ };
|
|
|
|
+ dsa {
|
|
compatible = "marvell,dsa";
|
|
#address-cells = <2>;
|
|
#size-cells = <0>;
|
|
@@ -163,22 +172,22 @@
|
|
};
|
|
|
|
partition@200000 {
|
|
- label = "kernel";
|
|
+ label = "kernel1";
|
|
reg = <0x200000 0x2A0000>;
|
|
};
|
|
|
|
partition@4A0000 {
|
|
- label = "rootfs";
|
|
+ label = "rootfs1";
|
|
reg = <0x4A0000 0x1760000>;
|
|
};
|
|
|
|
partition@1C00000 {
|
|
- label = "alt_kernel";
|
|
+ label = "kernel2";
|
|
reg = <0x1C00000 0x2A0000>;
|
|
};
|
|
|
|
partition@1EA0000 {
|
|
- label = "alt_rootfs";
|
|
+ label = "rootfs2";
|
|
reg = <0x1EA0000 0x1760000>;
|
|
};
|
|
|
|
@@ -209,53 +218,6 @@
|
|
|
|
&mdio {
|
|
status = "okay";
|
|
-
|
|
- switch@10 {
|
|
- compatible = "marvell,mv88e6085";
|
|
- #address-cells = <1>;
|
|
- #size-cells = <0>;
|
|
- reg = <16>;
|
|
-
|
|
- ports {
|
|
- #address-cells = <1>;
|
|
- #size-cells = <0>;
|
|
-
|
|
- port@0 {
|
|
- reg = <0>;
|
|
- label = "ethernet1";
|
|
- };
|
|
-
|
|
- port@1 {
|
|
- reg = <1>;
|
|
- label = "ethernet2";
|
|
- };
|
|
-
|
|
- port@2 {
|
|
- reg = <2>;
|
|
- label = "ethernet3";
|
|
- };
|
|
-
|
|
- port@3 {
|
|
- reg = <3>;
|
|
- label = "ethernet4";
|
|
- };
|
|
-
|
|
- port@4 {
|
|
- reg = <4>;
|
|
- label = "internet";
|
|
- };
|
|
-
|
|
- port@5 {
|
|
- reg = <5>;
|
|
- label = "cpu";
|
|
- ethernet = <ð0port>;
|
|
- fixed-link {
|
|
- speed = <1000>;
|
|
- full-duplex;
|
|
- };
|
|
- };
|
|
- };
|
|
- };
|
|
};
|
|
|
|
&uart0 {
|
|
@@ -274,10 +236,14 @@
|
|
};
|
|
|
|
/* eth1 is connected to the switch at port 6. However DSA only supports a
|
|
- * single CPU port. So leave this port disabled to avoid confusion.
|
|
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
|
|
*/
|
|
ð1 {
|
|
- status = "disabled";
|
|
+ status = "okay";
|
|
+ ethernet1-port@0 {
|
|
+ speed = <1000>;
|
|
+ duplex = <1>;
|
|
+ };
|
|
};
|
|
|
|
/* There is no battery on the board, so the RTC does not keep
|