KumiSystems/openwrtv4
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv4/target/linux/kirkwood/image/Makefile
Ademar Arvati Filho 27b2f0fc0f kirkwood: add support for Iomega Storcenter ix2-200 
Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
 Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
 flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC

Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console

Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    setenv serverip 192.168.1.1
    setenv ipaddr 192.168.1.13
    tftpboot 0x00800000 factory.bin
    nand erase 0x100000 $(filesize)
    nand write 0x00800000 0x100000 $(filesize)
    run bootcmd
    ```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
    ```
    mkfs.ext2 -L ext2 /dev/sdh1
    mount -t ext2 /dev/sdh1 /mnt
    cp initramfs-uImage /mnt/initramfs.bin
    umount /mnt
    ```
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
    ```
3. log into openwrt and sysupgrade to install into flash
    ```
    sysupgrade -n /tmp/sysupgrade.bin
    ```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-30 15:21:00 +02:00

155 lines
4.3 KiB
Makefile
Raw Blame History

#
# Copyright (C) 2009-2013 OpenWrt.org
#
# This is free software, licensed under the GNU General Public License v2.
# See /LICENSE for more information.
#
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
KERNEL_LOADADDR:=0x8000
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL := kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
KERNEL_SUFFIX := -uImage
KERNEL_IN_UBI := 1
PAGESIZE := 2048
SUBPAGESIZE := 512
BLOCKSIZE := 128k
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-ubi
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
endef
define Device/cisco_on100
DEVICE_TITLE := Cisco Systems ON100
DEVICE_DTS := kirkwood-on100
DEVICE_PACKAGES := kmod-i2c-mv64xxx
KERNEL_SIZE := 5376k
KERNEL_IN_UBI := 0
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
BOARD_NAME := on100
endef
TARGET_DEVICES += cisco_on100
define Device/cloudengines_pogoe02
DEVICE_TITLE := Cloud Engines Pogoplug E02
DEVICE_DTS := kirkwood-pogo_e02
BOARD_NAME := pogo_e02
SUPPORTED_DEVICES += pogo_e02
endef
TARGET_DEVICES += cloudengines_pogoe02
define Device/cloudengines_pogoplugv4
DEVICE_TITLE := Cloud Engines Pogoplug V4
DEVICE_DTS := kirkwood-pogoplug-series-4
DEVICE_PACKAGES := kmod-usb3
endef
TARGET_DEVICES += cloudengines_pogoplugv4
define Device/iom_iconnect-1.1
DEVICE_TITLE := Iomega Iconnect
DEVICE_DTS := kirkwood-iconnect
BOARD_NAME := iconnect
SUPPORTED_DEVICES += iconnect
endef
TARGET_DEVICES += iom_iconnect-1.1
define Device/iom_ix2_200
DEVICE_TITLE := Iomega StorCenter ix2-200
DEVICE_DTS := kirkwood-iomega_ix2_200
DEVICE_PACKAGES += kmod-gpio-button-hotplug kmod-i2c-mv64xxx kmod-hwmon-lm63
DEVICE_TYPE:=nas
PAGESIZE := 512
SUBPAGESIZE := 256
BLOCKSIZE := 16KiB
KERNEL_SIZE := 3072k
KERNEL_IN_UBI := 0
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 32505856
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | check-size $$$$(IMAGE_SIZE)
endef
TARGET_DEVICES += iom_ix2_200
define Device/linksys_audi
DEVICE_TITLE := Linksys EA3500 (Audi)
DEVICE_PACKAGES := kmod-mwl8k swconfig wpad-mini kmod-gpio-button-hotplug
DEVICE_DTS := kirkwood-linksys-audi
KERNEL_SIZE := 2624k
KERNEL_IN_UBI := 0
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
BOARD_NAME := linksys-audi
SUPPORTED_DEVICES += linksys-audi
endef
TARGET_DEVICES += linksys_audi
define Device/linksys_viper
DEVICE_TITLE := Linksys E4200v2 / EA4500 (Viper)
DEVICE_PACKAGES := kmod-mwl8k swconfig wpad-mini kmod-gpio-button-hotplug
DEVICE_DTS := kirkwood-linksys-viper
KERNEL_SIZE := 2688k
KERNEL_IN_UBI := 0
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
BOARD_NAME := linksys-viper
SUPPORTED_DEVICES += linksys-viper
endef
TARGET_DEVICES += linksys_viper
define Device/raidsonic_ib-nas62x0
DEVICE_TITLE := RaidSonic ICY BOX IB-NAS62x0
DEVICE_DTS := kirkwood-ib62x0
BOARD_NAME := ib62x0
SUPPORTED_DEVICES += ib62x0
endef
TARGET_DEVICES += raidsonic_ib-nas62x0
define Device/seagate_dockstar
DEVICE_DTS := kirkwood-dockstar
DEVICE_TITLE := Seagate FreeAgent Dockstar
BOARD_NAME := dockstar
SUPPORTED_DEVICES += dockstar
endef
TARGET_DEVICES += seagate_dockstar
define Device/seagate_goflexnet
DEVICE_TITLE := Seagate GoFlexNet
DEVICE_DTS := kirkwood-goflexnet
BOARD_NAME := goflexnet
SUPPORTED_DEVICES += goflexnet
endef
TARGET_DEVICES += seagate_goflexnet
define Device/seagate_goflexhome
DEVICE_TITLE := Seagate GoFlexHome
DEVICE_DTS := kirkwood-goflexhome
BOARD_NAME := goflexhome
SUPPORTED_DEVICES += goflexhome
endef
TARGET_DEVICES += seagate_goflexhome
define Device/zyxel_nsa310b
DEVICE_TITLE := ZyXEL NSA310b
DEVICE_DTS := kirkwood-nsa310b
DEVICE_PACKAGES := kmod-r8169 kmod-gpio-button-hotplug kmod-hwmon-lm85
BOARD_NAME := nsa310b
endef
TARGET_DEVICES += zyxel_nsa310b
define Device/zyxel_nsa325
DEVICE_TITLE := ZyXEL NSA325 (v1 and v2)
DEVICE_DTS := kirkwood-nsa325
DEVICE_PACKAGES := kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
BOARD_NAME := nsa325
endef
TARGET_DEVICES += zyxel_nsa325
$(eval $(call BuildImage))
Reference in a new issue View git blame Copy permalink