This automatically writes to the alternate firmware partition
(on Linksys's dual firmware layout) using code borrowed from
the WRT1900AC port.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47434
This is done with existing code from the WRT1900AC port.
It makes sure the "auto_recovery" bootloader option is set,
and resets the s_env boot counter after a successful boot.
This gives users without a serial console connection some
measure of safety.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47433
This is done with the new image generation system and board names.
It also generates a sysupgrade.tar image.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47432
This is imported verbatim from the mvebu WRT1900AC port.
It picks up the current boot partition from the kernel command line,
then renames that partition "ubi" so that it auto-mounts.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47431
- Use board engineering names rather than marketing names
- Linksys uses a dual firmware layout, where the bootloader
will switch to the other stored image when one fails to
boot three consecutive times.
In order to make this firmware compatible with the factory
images and the stock bootloader we must match this layout.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47429
Add a new config option "channels" for mac80211 wifi devices. It's only
valid if automatic channel selection is used and restricts the channel
selection to one of the given channels.
config wifi-device
list channels 1
list channels 6
list channels 11
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47427
as conntrack and conntrackd are completely independent programs,
serving a different purpose.
Also split by other distributions, as Debian and Ubuntu.
Signed-off-by: Ulrich Weber <uw@ocedo.com>
SVN-Revision: 47424
default configuration will fill up disk by
writing /var/log/conntrackd-stats.log
Introduced due init script auto start.
Signed-off-by: Ulrich Weber <uw@ocedo.com>
SVN-Revision: 47422
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
When running "make kernel_menuconfig" right after "make clean", we error
out with the following message:
Makefile:22: recipe for target '.../build_dir/target-arm_cortex-a7_musl-1.1.10_eabi/linux-.../linux-3.18.18/.quilt_checked' failed
make[2]: [.../build_dir/target-arm_cortex-a7_musl-1.1.10_eabi/linux-.../linux-3.18.18/.quilt_checked]
Error 127 (ignored)
The root cause of the problem is located in the OpenWrt specific quilt
patch, which sets the quilt install directory to $STAGING_DIR/../host.
However, on a clean environment (right after running "make clean"),
$STAGING_DIR doesn't exist. The "quilt" executable doesn't find its
different commands, errors out, and creates this message.
We're fixing it by using $STAGING_DIR_HOST rather than $STAGING_DIR,
which is absolute. It will work even if there is no target directory
yet.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47410
Certains host packages (like quilt) need to know the previously used
install location at run-time. They currently use $STAGING_DIR, which
causes issues on cleaned environment, where $STAGING_DIR doesn't exist
yet.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 47409
In order to set the multicast rate for mesh point interfaces the "mesh join"
was made explicit and moved to mac80211_setup_vif(), similar to how it is
done for IBSS interfaces.
Previously, the mesh join was made implicit in case authentication (i.e.
$key) was not used when creating the interface in mac80211_prepare_vif(),
while using authentication would create the interface first, then join
later in mac80211_setup_vif() by starting authsae.
Signed-off-by: Nils Schneider <nils@nilsschneider.net>
SVN-Revision: 47408
* remove references to non-existing kmod-usb3-mt7621
* ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 47407
The hardware of the v3 is identical to the v2.
Based-on-patch-by: Andreas Ziegler <github@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47406
Some devices require the kernel to be in a JFFS2 file system. Make the
support for this more generic so that it can be used by other devices.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
SVN-Revision: 47404
In case if we're interested in generation of non-binary images
(for example if we want images to be valid .elfs - and that's what we
want for ARC now) we have to instruct Device/Build/initramfs target to
use input file with some extension (in case of ARC it will be
essentially .elf).
Otherwise default binary vmlinux-initramfs (without extension) is used and
resulting images then are binaries instead of elfs.
Now having KERNEL_INITRAMFS_NAME variable it's possible to substitute
default $$(KERNEL_NAME)-initramfs with preferred option like
$$(KERNEL_NAME)-initramfs.elf.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
SVN-Revision: 47403
Update scons to 2.4.0.
Change mirror (as the previous one is missing the current version).
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47392
