The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
SOC: BCM63168 (BMIPS4350 V8.0 @400MHz)
Flash size: 16 MiB
RAM size: 128 MiB
Heavily based on patch for OpenWRT Chaos Chalmer.
Original patch and more info can be found at:
https://openwrt.org/toh/sky/sr102
Known issues:
- Wireless and ADSL modem are not working.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" could very
well fix the freezes that have been reported on the forum by
@ticerex and @takimata.
<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/46>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The code has some remaining issues that cause ethernet hangs, so
disable it for now until we can get it fixed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The line that produces factory image was accidentally left by me while
testing before inital commit.
I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).
I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.
So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Extend the small_flash feature to disable swap, core dumps, and
kernel debug info, and change the squashfs block size to 1024KiB.
Also change squashfs fragment cache to 2 for small_flash to ease memory
usage.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Add a new config option to allow to select the default compile
optimization level for the kernel.
Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.
Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.
Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.
Exceptions to the above are:
- lantiq, where the optimization for size is only required for the
xway_legacy subtarget but was set for the whole target
- mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
plenty of space and an optimization for size doesn't make much sense
- rb532, which has 128MByte flash
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move boards to the tiny subtarget which break the build if the kernel is
set to "Optimize for performance".
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the latest version of u-boot (2018.05) there was a swith to
Hush shell for ARC AXS10x boards(arc770/archs38):
commit 9249d74781e1 ("ARC: AXS10x: Enable hush shell").
In Hush shell using "$()" to declare envitonment variables is forbidden,
instead of this "${}" need to be used.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
The changed applied to BananaPi R2 in upstream commit c0b0d540db1a,
which was backported to 4.14 in 4.14.53, is also required for the U7623.
Without updating the memory node, the board refuses to boot.
Fixes: d0839e020d ("kernel: bump 4.14 to 4.14.53")
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
- remove misaligned custom buffer allocation in the NAND driver
- remove broken bounce buffer implementation for 16-byte align
Let the MTD core take care of both
Fixes messages like these:
[ 102.820541] Data buffer not 16 bytes aligned: 87daf08c
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Newer kernels have a patch that implements compatible functionality
directly. Adjust the attribute of our own patch in preparation for
dropping it later
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rereshed all patches
Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Partition name is picked by a parser_trx_data_part_name(). It has to
get correct partition offset (taking care of bad blocks) to work
properly.
This fixes UBI support for devices that have kernel flashed on partition
with a bad block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit adds support for the OCEDO Raccoon
SOC: Atheros AR9344
RAM: 128MB
FLASH: 16MiB
WLAN1: AR9344 2.4 GHz 802.11bgn 2x2
WLAN2: AR9382 5 GHz 802.11an 2x2
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
NOTE: The U-Boot won't boot with the serial attached.
Boot the device without serial attached and attach it
after 3 seconds.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'raccoon-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'raccoon-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_USB_MTU3 is not visible for the mediatek target by default, but
only when CONFIG_USB_GADGET is set. This will config option will be
remove with when running "make kernel_oldconfig", move this option to
the generic config to prevent this.
This fixes the build of the mt7623 subtarget of the mediatek target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shrink the tiny kernel by moving all switch and ethernet phy drivers to
the generic kernel config instead of the target kernel config.
All boards in the tiny and nand target are either ar7240 or ar9331 based,
which don't support external xMII and therefore no external ethernet phy
can be connected. None of the boards uses a realtek switch either.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
Add a template for safeloader images and include it instead of
overwriting variables defined in the common tp-link build commands.
Split the existing tp-link templates to proper implement the safeloader
template.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop the LOADER_TYPE variables in case no loader is used at all or move
the variable to devices which are using a loader.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the provided image build variables to point the kernel-bin build
command to the kernel we are interested in.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the LOADER_TYPE variable to specify that we need the elf preloader
and append the loader via the corresponding build recipe. It allows to
enable initramfs images again for mikrotik NAND images, which caused a
build error before.
Add the minor header only to the kernel of the sysupgrade images, as it
is only required for the bootloader to find the kernel on flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
I-O DATA WN-AX1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Stock firmware:
In the stock firmware, WN-AX1167GR has two os images each composed of
Linux kernel and rootfs.
These images are stored in "Kernel" and "app" partition of the
following partitions, respectively.
(excerpt from dmesg):
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"
The flag for boot partition is stored in "Key" partition, and U-Boot
reads this and determines the partition to boot.
If the image that U-Boot first reads according to the flag is
"Bad Magic Number", U-Boot then tries to boot from the other image.
If the second image is correct, change the flag to the number
corresponding to that image and boot from that image.
(example):
## Booting image at bc800000 ...
Bad Magic Number,FFFFFFFF
Boot from KERNEL 1 !!
## Booting image at bc060000 ...
Image Name: MIPS OpenWrt Linux-4.14.50
Image Type: MIPS Linux kernel Image (lzma compressed)
Data Size: 1865917 Bytes = 1.8 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
raspi_erase_write: offs:f90000, count:34
.
.
Done!
Starting kernel ...
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AX1167GR
2. Connect power cable to WN-AX1167GR and turn on it
3. Access to "192.168.0.1" on the web browser and open firmware
update page ("ファームウェア")
4. Select the OpenWrt factory image and perform firmware update
5. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-AX1167GR
6. Wait ~180 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
USB storage support is however SCSI Disk block device support isn't
meaning that connected devices wont enumerate.
Enable CONFIG_BLK_DEV_SD by default to fix it.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
BusyBox's `tar` command does not support the `--directory` directive, which
is essentially `-C` in short-form option.
BusyBox's `tar` command supports `-C`.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
These options are handled by generic configuration
Targets that need these options should select KERNEL_DEVMEM
and/or KERNEL_DEVKMEM options on OpenWRT's config
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC. However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines. If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.
This commit overrides the incorrect dt node definition in the included
file.
See also:
- https://bugs.openwrt.org/index.php?do=details&task_id=1262
- https://community.nxp.com/thread/338432#comment-474107
Signed-off-by: Tim Small <tim@seoss.co.uk>
Add two patches submitted for upstream review that significantly improve
the dwc2 driver on openwrt from kernel stability and performance
perspectives.
Fixes: FS#1367
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
TP-Link Archer C7 v2 USB port LED and GPIO names are in incorrect order,
i.e. in order to match actual user visible labels, usb1 should be usb2,
and vice versa.
This patch swaps LED and GPIO power control node names.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Due do a missing KCONFIG isn't selectable nor enabled in the target
kernel config. Drop it for now and enable/add the driver at the time it
is required.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Specification:
- System-On-Chip: MediaTek MT7628NN
- CPU/Speed: 580 MHz
- Flash-Chip: ELM Technology GD25Q64
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7628N 2.4GHz 802.11bgn
Currently the only method to install openwrt for the first time is via
TFTP recovery. After first install you can use regular updates.
Flash instructions:
1) To flash the recovery image, start a TFTP server with IP address
192.168.0.66 and serve the recovery image named tp_recovery.bin.
2) Connect your device to the LAN port, then press the WPS and Reset
button and power it up. Keep pressing the WPS/Reset button for
10 seconds or until the lock LED is lighting up.
It will try to download the recovery image and flash it.
It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.
Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
Specification:
- System-On-Chip: MT7628N/N
- CPU/Speed: 580 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (57600 8n1)
- Wireless No1 (2T2R): SoC-integrated: MT7628N 2.4GHz 802.11bgn
- Wireless No2 (2T2R): On-board chip: MT7612EN 5GHz 802.11ac
- USB: Yes 1 x 2.0
- 4x LED, 3x button
The device supports dual boot mode. So we use only first half of flash.
Flash instruction:
The only way to flash OpenWrt image is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-zyxel_keenetic-extra-ii-squashfs-factory.bin"
to "kextra2_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
This commit adds support for the MikroTik RouterBOARD RBM11g.
=Hardware=
The RBM11g is a mt7621 based device featuring one GbE port and one
miniPCIe slot with a sim card socket and USB 2.0.
==Switch==
The single onboard Ethernet port is connected the CPU directly.
The internal switch of the mt7621 SoC is disabled.
==Flash==
The device has one spi nor flash chip. It is a 128 Mbit winbond 25Q128FVS
connected to CS0.
==PCIe==
The board features a single miniPCIe slot. It has a dedicated mini SIM
socket and a USB 2.0 port. Power to the miniPCIe slot is controlled via
GPIO9.
==USB==
There are no external USB ports.
==Power==
The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack (center-positive). The input voltage range is 11-32 V.
==Serial port==
The device does have an onboard UART on an unpopulated header next to the
flash chip:
GND: pin 2
TX: pin 7
RX: pin 6
Settings: 115200, 8N1
See below illustration for positioning of the header.
0 = screw hole
* = some pin
T = TX pin
R = RX pin
G = GND pin
Pinout:
+---------------
|O
| __
| / \
| \__/
|
|
|
| +---+
| |RAM|
| +--+ | |
| |**| <- unpopulated header with UART
| |*T| +---+
| |R*| +--------+
| |**| | |
| |G*| | CPU |
| +--+ | |
| +--+ | |
| | | +--------+
| +--+ <- flash chip
|O
| +-----+
| | |
|+--+ | |
|| | | |
+---------------------
=Installation=
To install an OpenWRT image to the device two components must be built:
1. A openwrt initramfs image
2. A openwrt sysupgrade image
===initramfs & sysupgrade image===
Select target devices "Mikrotik RBM11G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin" in the
output directory.
==Installing==
**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the
created license file.**
When rebooted the board will try booting via ethernet first. If your
board does not boot via ethernet automatically you will have to attach
to the serial port and set ethernet as boot device within RouterBOOT.
1. Set up a dhcp server that points the bootfile to tftp server serving
the "openwrt-ramips-mt7621-mikrotik_rbm11g-initramfs-kernel.bin"
initramfs image
2. Connect to ethernet port on board
3. Power on the board
4. Wait for OpenWrt to boot
Right now OpenWrt will be running with a SSH server listening. Now
OpenWrt must be flashed to the devices flash:
1. Copy "openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
to the device using scp.
2. Write openwrt to flash using "sysupgrade
openwrt-ramips-mt7621-mikrotik_rbm11g-squashfs-sysupgrade.bin"
Once the flashing completes the board will reboot. Disconnect from the
devices ethernet port or stop the DHCP/TFTP server to prevent the device
from booting via ethernet again.
The device should now boot straight to OpenWrt.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.
Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.
Available flash space for rootfs+overlay increases from 48MB to 124MB.
Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.
Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.
Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.
Signed-off-by: Michael Kuron <m.kuron@gmx.de>
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.
Fixes: FS#1620
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't mask bit 4 of the AT8022 phy id. If bit 4 of the AT8022 phy id
(0x004dd023) is masked, it will match the phy id of the AR8327 switch
(0x004dd033) as well.
It results in applied at803x driver settings/callbacks, which will at
least limit the AR8327 phys to 100MBit operation instead of the possible
1000MBit.
Signed-off-by: Mathias Kresin <dev@kresin.me>
