[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36580
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36579
Here is corrected version (only thing not working are wifi LEDs).
[juhosg: this has been created from the following patch:
http://patchwork.openwrt.org/patch/3620/ ]
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36578
These devices are actually built around the 8devices Carambola dev board.
ARC FreeStation, Flex mARC, iFlex, and SplitStation devices are
supported with this image, see "ARCFlex Firmware Downloads":
http://www.antennas.com/wiki/index.php?title=ARC-OS_Firmware_Downloads_and_Revision_History
Funnily enough if present the external USB wlan ends up being wlan-0, with the
SoC device being wlan-1.
- Invert port map so special handling of vlan config can be removed.
- Add LED config similar to original ArcOS firmware.
- Add GPIO export for enabling PoE passthrough from ethernet port 0 to port 1
- Get MACs from factory partition.
- Update description to list supported devices.
- Carambola uses RT3050 (not RT3052), though my Carambola CPU
actually reports itself as being an RT3350 while still having
RT3050F markings.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 36564
And while at it, also include a define check for BCM6328, thanks to
Gabor for spotting this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 36506
Update the numbering of kernel patch for supporting
Netgear WNR2000v3 from 617 to 618.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36498
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.
The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 36482
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36459
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36456
Only difference between Generic and P1020 is that P1020
enables SMP with two CPUs in the kernel config.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36454
This upgrades the AT91 target to 3.8.7, and migrates to device tree.
This allows a single kernel to be built for most at91 variants which
simplifies things quite a bit. The immediate result is that all
subtargets are nuked, and any boards without dts files are no longer
supported, though the target now includes more boards than before. The
adc driver was also nuked as 3.8.7 includes a new one under the IIO
subsystem.
Signed-off-by: Adam Porter <porter.adam@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36452
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports':
drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36442
Now that ALL5002 and ALL5003 each got their own DTS and board names, remove
the now no longer needed user-space part which previously differentiated between
ALL5002 and ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3558/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36436
Prior to the switch to 3.8, ALL5002 and ALL5003 boards shared mach-all5002.c.
With the change to DTS, this is no longer accurate, as ALL5002 is based on
Rt3352 SoC while ALL5003 is based on Rt5350 SoC, therefore the corresponding
rt5350.dtsi need to be included for ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3557/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36435
This board uses a TrendChip SOC with its own RAM/Flash for ADSL support.
We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN.
There are two versions (Chile 8MB and Spain 16MB).
Wiki: http://wiki.openwrt.org/toh/alpha/asl26555
Signed-off-by: Esteban Benito <estebanjbs@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3571/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36433
Fixes the following warning:
CC [M] net/ipv6/addrconf.o
net/ipv6/addrconf.c: In function 'addrconf_init':
net/ipv6/addrconf.c:4944:2: warning: assignment from incompatible pointer type [enabled by default]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36364
prepare_generic_squashfs was called twice on the generated images breaking mount_root
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36349