This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)
Modified after cherry-pick:
obj in Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756
If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1
To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 8d924d43c0ea6839a3a33e54982e8da48b736001)
Modified after cherry-pick:
compatible attribute
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on ar71xx, brcm47xx, kirkwood.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
Thanks to leaving .pattern file we can easily insert extra step between
linksys-pattern-partition and trx-v2-with-loader, e.g. rootfs one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Fixes the same hctosys init issue as described in commit
5481ce9a11
The Gateworks Ventana family uses an emulated Dallas 1672
RTC device.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Support splitting WRGG images, found in some D-Link devices (e.g.
DAP-2695).
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO
For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f
For debugging serial console is easily visible on board, no soldering needed.
Signed-off-by: André Valentin <avalentin@marcant.net>
This bugfix enables FXS support on dabube based devices.
Changed "compatible" attribute from "vmmc" to "vmmc-xway".
The vmmc driver uses "vmmc-xway".
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.
Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
Remove redundant code: merge boards/cases that share
the same network configuration.
Also fix the alphabetical ordering of the cases.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
These boards do not have a switch, so they should have never been added
to this file in the first place.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space
after u-boot-env is used to store the boards Mac address. Sadly as this
was removed on any device already on OpenWRT/LEDE, moving forward a new,
64k partition named "mac" will be used to store the mac address for the
device (which is the minimum size). This allows users to properly set
the correct MAC, without editing the ART partition (which holds the same
MAC for all devices).
The reason the space is taken from kernel instead of rootfs is currently
kernels are only 1.3MB, so that way we can leave the current rootfs
space alone for users who fully utilize the available storage space.
Once this partition is added to a device, you can set your MAC doing the
following:
mtd erase mac
echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5
sync && reboot
Where 00:18:0a:33:44:55 is your MAC address.
This was tested, and confirmed working on both the MR12 and MR16.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This moves the Meraki MR12 and Meraki MR16 to the new generic target.
Tested and verified working on both devices.
Note that kernel/rootfs images are still generated. This is because they
are used for the inital flashing process due to the fun pace at which
UBoot erases/writes to SPI.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Otherwise if we use ds1307 as kernel module, hctosys fails as ds1307 is
being initialized later then hctosys:
[ 2.427349] hctosys: unable to open rtc device (rtc0)
[ 3.714263] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
[ 8.990061] rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Refresh patches for all targets supporting 3.18 and not marked broken.
Compile-tested on all targets using 3.18 and not marked broken.
Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Refresh patches for all targets supporting 4.1 and not marked broken.
Compile-tested on all targets using 4.1 and not marked broken.
Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.
Changes to generic/666-Add-support-for-MAP-E-FMRs-mesh-mode.patch based
on a90ee92337.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 4.4 was ready for brcm47xx for almost a year now but I kept
postponing the bump due to problems with Linksys WRT300N v1.0. OpenWrt
and LEDE with 4.4 were hanging at the booting with the:
> Starting program at 0x80001000
(the last CFE message).
This was a permanent state, "make distclean" wasn't helping, I spent
hours debugging this and I was reliably reproducing the issue every
time. I also reported it on linux-mips ML in the thread:
> BCM4704 stopped booting with 4.4 (due to vmlinux size?)
After ~month I started working on WRT300N again. I got hangs as expected
every time I switched from 4.1 to 4.4. I started experimenting with:
1) TRX content (I tried dropping rootfs partition)
2) BZ_TEXT_START of lzma-loader
3) Flashing other variants of image: lzma compressed kernel (without a
loader), gzip compressed one, uncompressed one.
At some point I got rootfs-less image booting and after that I couldn't
reproduce problem anymore, even with a complete firmware. It seems like
hardware was in some locked/unstable state that got magically fixed.
I have LEDE working now, tested it even with "make distclean", it seems
we can bump kernel now. I'll keep testing it on WRT300N for some time.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Linksys WRT300N V1 has pretty bugged CFE bootloader (it crashes in a lot
of situations) that doesn't accept .bin image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
